Speedybee F405 Wing Mini ZOHD Drift FPV Build
Вставка
- Опубліковано 3 сер 2024
- #zohd #fpvbuild #fpv #speedybee #speedybeef405wingmini #inav #elrs #walksnail
Plane of choice for the Speedybee F405 Wing Mini is the ZOHD Drift.
Setup quickly with INAV 7.0 firmware in the previous video, we are now ready to install and setup the flight controller with GPS and an ELRS receiver and do all the appropriate INAV configurations needed to install all electronics into this tight build.
Chapters
0:00 Intro
0:33 ZOHD Drift First Look - Build Possibilities - Quick Build
4:40 The Build Plan
7:12 BN220 GPS INAV 7 Setup and Install
11:37 Happymodel ELRS ES900 Reciever Install
13:19 INAV 7 Board Alignment and Double Checking Setup
16:30 Double Checking Hardware Before Install
17:47 Checking and Fixing Motor Rotation
19:49 Testing Servos and Final INAV check Before Install
22:01 Checking The Control Surface Throw Rates
23:46 Installing The Electronics Into The Craft
24:48 Post Install and Setup Thoughts and Suggestions
26:31 Confirming Control Surfaces Are Correct and Correcting
28:25 ESC Calibration
28:55 Post Build Thoughts and Suggestions
Airport Lounge - Disco Ultralounge by Kevin MacLeod is licensed under a Creative Commons Attribution 4.0 license. creativecommons.org/licenses/...
Source: incompetech.com/music/royalty-...
Artist: incompetech.com/
![☀ Полный фарш до 250 грамм. Самолёт на каждый день. [ZOHD Drift Dark Breeze]](http://i.ytimg.com/vi/3iItGAI4dhs/mqdefault.jpg)
![☀ Полный фарш до 250 грамм. Самолёт на каждый день. [ZOHD Drift Dark Breeze]](/img/tr.png)
![☀ Достойное сердце для серьезной птички [Speedybee F405 Wing Mini]](http://i.ytimg.com/vi/Ku9Na3thOuw/mqdefault.jpg)
Nice job, I noticed you still have the ESC BEC lead connected to the FC. It's suggested to remove the red ESC BEC wire from the FC due to conflicting voltages which can cause problems for the regulator. Otherwise, good luck on your maiden and happy flying!
Yes thanks for picking that up I did in the end.
If the esc has a built in bec I unhook it but if it's a esc wo bec I don't bother
Hi, as I’m still trying to learn from you kind experts could I please ask why the BEC would have use for that red wire if it causes voltage conflicts? Would it be used in a different way in another setup?
@@Double-D_291 The red ESC BEC wire is used in traditional RC airplane setups for powering your RX and servos when not using an FC.
@@Double-D_291 yes disconnecting it when using a flight controller is recommended as it can be used to power rx and servos in older non FC setups. Exactly as madsloper said above
Geeze, that's tight, just had the thought until I watched your video, might just stick with the Kopilot. Well done, Nice job.
@@QuadographyAustralia1965 it's tight but works well. Thanks for watching ,👍
The Kopilot just fits, works as advertised.
BNF version inc camera is good 'My First Wing'
Many thanks for sharing this detailed video! 👍 Already ordered my ZOHD Drift.
Thank no problem, enjoy the drift ride!
Look forward to your flight video 👍
Hopefully next week weather here is starting to improve
Excellent job 👍👍👍
Thank you
Most reports indicate the CG nubbins are too far back, by about 3 to 5 mm. A little nose down helps penetration, especially if using small battery.
@@PiDsPagePrototypes I have heard this too although when I check the CG it definitely flies best a little nose heavy indeed.
hello! How can fix the video transmitter and camera (which port?)
This plane is very light and should Only be flown in light wind. It's like a glider with a motor, beautiful glide but hard to land in a breeze.
Totally nice plane to fly slow, I did the maiden with fullload including walksnail had setup and on 2s battery and it had no problem taking off and flying. Maiden video coming soon.
I found that the CG factory marks are Wrong. I used the servo wires as the CG and it works perfectly. Others had the same problem.
Ok thanks interesting I did maiden with 2s using the CG marks under the wings and takeoff was faultless. I did make an attempt to make it slightly nose heavy though.
Hey, great video mate. I'm trying to do the exact same assembly but I'm having issues with motor, just keeps beeping and does nothing else. Servos do work but the motor just doesn't, tried other motors and is the same, slow beep and if I change the esc from port it goes faster. Any ideas?
Thanks a lot.😅
Thanks for the comment much appreciated.
Sounds odd have you calibrated the esc? Sounds like the motor is fine as you have tried other motors problem may be with the esc. Just to note in this video i did have the 5v cable on the esc bec connected by mistake should only have signal and neg wire only as it can cause issues. Other than that it seems unusual but i would try look at changing esc to see if it helps.
Have exactly same issues
Motor and servo dont works !
CRSF bind, esc beep constantly :(
What port did you allocate for your elrs receiver?
Theres no info anywhere that shows the uart locations.
Wish youd have shown that vital initial part of the setup, its useless without transmitter and receiver communication.
It's setup in uart1. I have previous videos on the speedybee f405 wing mini and a fairly detailed review on it which should help with setup.
I have the SpeedyBee F405 WING APP. Just working through connections issues.
SpeedyBee App on my phone doesn’t connect. I’m wondering what you did to make it work?
Also, I have a freshly formated, MS-DOS (FAT-32) 8GB in the slot. However, on the Blackbox tab, at the bottom, still shows RED Fatal error Reboot to retry. Should that change color?
Thanks!
Regarding connection to the app the usb extender light should flash green. The 3 modes can be changed by holding the button down for 6seconds. Off the top of my head I believe green is what you want and there is purple and white and off (no light). If it’s green you should be able to connect your phone to it through the settings in the phone. And also the formatted sd card should work fine once installed into the flight controller it should be automatically pickup up maybe you need to toggle the black box switch in config.
Thanks for your reply. I’ve gone through that process a number of times, following the instructions included with my SpeedBee F405 WING. I’m unable to get a wireless connection. Pressing the boot button for six seconds…
Green slow flashing: BLE not connecting!
Pressing the boot button for six seconds…
White slow flashing: Wi-Fi not connecting!
Pressing the boot button for six seconds…
Blue slow flashing: Classic Bluetooth SPP not connecting!
Pressing the boot button for six seconds…
RGB LED off: Wireless module turned off.
I’m watching other UA-camrs do what you’re doing, looks like magic. But for me, it’s not working.
@@AcadJim sorry to hear sounds frustrating and I take it you have connected from the phone wifi setting to recognise the speedybee on the app too? Other than that you may have a possible bad module, try contacting speedybee for support they have helped me out a few times with issues.
@@stonesrcchannel I’m now working with SpeedyBee tech support for help. They’re on it! Thanks and have a great FPV flight 👍🏼
@@AcadJim thanks I hope you sort it out.
I have both the black one and the white 1.The black one is made out of a different foam and is not nearly as strong as the white 1, but in my original, I run an F405WTE and in the black 1 I run the f405WMN... I'm running a dual camera analog system on the white one.And a walksnail on my black one..
1407/2800kv on black. 1408/4000kv on white one. Running 2200mah 3s Stock motors burned out very fast
I will keep mine running 2s since this video I have maidened it with hd fpv system and flew very well although not fast which is ok. I will have a video coming with the maiden soon.
@@stonesrcchannelyeah I've had mine over 60mph....
I tried 2s but it wasn't enough. I changed to these motors 1408 4000kv due to stock one being hot and then smoking and I had them do I used them. I love them I since bought the 1407 2800kv I didn't like them at first ...
My drifts have over 300 miles on each and now that inav 7.1 has the odometer now to keep track...
I fly my drifts as "warm up" they go on every outing and fly first. My main plane thinking of getting an baby a.r pro as well as the penguin
@@devilsreject78 nice idea they seem good as a tune up plane before flying something more challenging. I also love the odometer too wish it was out earlier to keep track of mileage in the rest of my fleet.
Penguin is also on my list as well as dolphin and swordfish.
@@stonesrcchannel I have both the dolphin and the swordfish in my favorite between all of them is definitely the swordfish it's like so amazingly smooth the dolphin awesome flies very very good but the swordfish definitely takes the cake