Just purchased a set of these and are about to install them on my wife's 2019 5th Gen RAM1500 Bighorn 4x4................thing is, do you sell Mud Flaps that go with these Flares??
Was wondering exactly the same … so watched the vid as slow as I could and it looks like the tires are a 285/55R20? The rims are the Black Rhino Barstow’s which (for 20’s) are a 20x9.5, and can only assume they are the +12 offset as the 0 offset ones would probably stick out further? Would be good to get this confirmed though … 🤷♂️
UPDATE: GAP ALERT - GAP ALERT - GAP ALERT.......These Flares that AMERICANTRUCKS sent me did "NOT" fit my 5th Gen 2019 RAM 15000 4x4, not even close!!!!..........There was a 3/8-1/2" gap between the flare and the exterior sheet metal.
If I had known what a hassle these were to install, and that you had to remove all the lower trim, I would not have purchased these. It took me two attempts and 2 days to complete
I installed the red rock fender flares on my 2020 RAM don’t like the 3M tape doesn’t stick on the ends of the flare I thought I was getting one like this in the video now I’m gonna have to get another one got disappointed with my flares.
I bought these and had many problems with the Tape not sticking, Lining the holes, closing the gaps, and setting the ends. These Chinese products are awful. Looking at the video, I also noticed that your video had many cuts during the installation. When Installing the tapes, lining the holes, etc., to make it look easy. I threw mine away and bought Booshwaker, made in the USA. And it fit just like it was made for my Ram. I installed all four within an hour, and they look factory-installed. Awesome. But I enjoyed watching your video as well. Thanks
I’ve begun installing some on my 2021 Ram 2500. The front went on fine. The back I’m have trouble with the inside plastic guard moving and I can’t get the fender flare and the inside guard to line up. Any suggestions?
Shop these RedRock 4x4 OEM Fender Flares! : amtrucks.at/3oemEak
You had me at rubber gasket.
Just purchased a set of these and are about to install them on my wife's 2019 5th Gen RAM1500 Bighorn 4x4................thing is, do you sell Mud Flaps that go with these Flares??
What is the wheel and tire setup on that truck. Is that a 33/12.50 with 18's maybe? Offset and width of rims would be helpful to know too. Thanks!
Was wondering exactly the same … so watched the vid as slow as I could and it looks like the tires are a 285/55R20? The rims are the Black Rhino Barstow’s which (for 20’s) are a 20x9.5, and can only assume they are the +12 offset as the 0 offset ones would probably stick out further? Would be good to get this confirmed though … 🤷♂️
UPDATE: GAP ALERT - GAP ALERT - GAP ALERT.......These Flares that AMERICANTRUCKS sent me did "NOT" fit my 5th Gen 2019 RAM 15000 4x4, not even close!!!!..........There was a 3/8-1/2" gap between the flare and the exterior sheet metal.
Anyone else have issues with some gapping for the front flares? Mine don’t sit flush in a few spots.
same issue with mine I tried to slip some 2 sided tape between the fender and flares which helped a little
If I had known what a hassle these were to install, and that you had to remove all the lower trim, I would not have purchased these. It took me two attempts and 2 days to complete
😂😂😂 no way, 2 days??
If you would have hit it with your purse it would been faster
2 days? Did you use your fingers to loosen and tighten all the bolts?
I installed the red rock fender flares on my 2020 RAM don’t like the 3M tape doesn’t stick on the ends of the flare I thought I was getting one like this in the video now I’m gonna have to get another one got disappointed with my flares.
I bought these and had many problems with the Tape not sticking, Lining the holes, closing the gaps, and setting the ends. These Chinese products are awful. Looking at the video, I also noticed that your video had many cuts during the installation. When Installing the tapes, lining the holes, etc., to make it look easy. I threw mine away and bought Booshwaker, made in the USA. And it fit just like it was made for my Ram. I installed all four within an hour, and they look factory-installed. Awesome. But I enjoyed watching your video as well. Thanks
I’ve begun installing some on my 2021 Ram 2500. The front went on fine. The back I’m have trouble with the inside plastic guard moving and I can’t get the fender flare and the inside guard to line up. Any suggestions?
I don’t have the rubber vinyl to protect my truck paint. Would you guys mind selling me just the rubber for the 4?
QUESTION!!! are these textured or smooth I can't tell?
Looks smooth to me
I’d like to know the answer to this as well. I want to paint them
GREAT VID!
Thanks for watching! -Zach
First!!!