Це відео не доступне.
Перепрошуємо.
Peugeot 407 2.0 Hdi Cambelt/Timing belt replacement ( Detailed Version)
Вставка
- Опубліковано 27 січ 2021
- Hello my guys and girls i have made a video for you of my own experience replacing cambelt, water pump, idler pulley and tension pulley on Peugeot 407 2.0 hdi. I have tried my absolute best to make a video witch would explain everything in a detail hence the length of the video is nearly 2 hours. I hope some of you will find this video use full. Also just to mention please tension your tention pulley anti clock wise only it should be an arrow drawing on a pulley showing which way it should be tensioned.
More room than a 2010 308 2.0HDI very good video , with the handy tip of marking the belt with three marks for lining up pre tension..Now to do mine.
It doesn’t matter which way the belt goes on I wouldn’t have counted the teeth. As long as the cam and flywheel is locked your good to go
Brilliant thanks, I just changed the cambelt on my Citroen C5 with this engine. It was a little harder because the coolant tank is the exact same on the C5 but you cant move it easily because the BHI unit for the Hydractive suspension is in the way! Mostly it is identical to this though and my flywheel had a simple 8mm hole for the timing unlike your 407. Fun job, One trick I do to make fitting the new belt easier is to mark the teeth with paint like you do and fitting on the cam sprocket you can use 2 tie wraps to hold it while you work below to fit the belt to the crank pulley and the rest. Thanks for your videos and keep up the good work!
Thank you mate I am glad you enjoy it.
What a guy!!! Such a good video, in details! Well done mate! Thanks a lot! Ačiu!
Nera uz ka. Aciu uz gera komentara.
Well what a brilliant video that was, so well explained watched the whole video straight through, would love to be able to do a similar job on my Citroen C5 X7 2008 with 58k miles however although I’m a retired marine engineer I’m now 73 years old and the aches and pains and rheumatoid arthritis is getting the best of me, that said I’ve now subscribed to your brilliant channel and look forward with interest to more videos, many thanks Mad4FrenchCars, Karl
Thank you very much for a nice comment mate. I will be making a ton of videos this year, hope you will find it Interasting. I like Citroen C5 they are nice cars. Thank you for subscribing.
Great videos. Have watched a few and your very detailed in your description. Just bought one and I'm getting air in the fuel and a leak on the inlet side of the filter. And mine is like yours with no details for the cambelt so this will be a perfect video for me to replace my belt. And also anyone who does thos should do the water pump at same time and external belts while you got them off
Thankyoumate comments like this makes my day. I in process of making few good vids for next week. If any questions then ask i am always here
Thanks for taking the time to do this. I need to do the crankshaft oil seal so will need to do the timing belt to get to it. The belt, pulleys and water pump are recent so just going to clean up and replace the belt if contaminated with oil. I appreciate your style of working in the back yard with basic tools, although I have ordered the flywheel locking tool!
Thankyou for a good comment mate. I 100% support professional locking tool is good thing to have and use. I think if I would do a cambelt now on any car I would do crankshaft seal and camshaft seal just to be on a safe side as its good to have it done and forget about it. And also they are not that expensive and then just other crankshaft seal then you do clutch.
I’ve got the same engine in my Ford Kuga and have a leaking crankshaft oil seal too. How did the job go? Mine also had cambelt done only two years / 8,000 miles ago. Sadly.
@@davidmbell Job went OK thanks. Used the old seal along with the sprocket to push the new one in - 1mm at a time with constant checking so as not to deform it or push it in too far! Did the camshaft seal too but very tricky - needs a variety of washers and round things. Flywheel locking tool essential for torquing up the crank pulley to avoid damage to the timing socket on the flywheel. Belt fairly easy to replace, tippex marks help a lot with this. Good luck.
Thank you, great video very detailed explanation easy to follow 👍👏🏆
Thank you.
The best video I've seen, great work, you made easy a difficult task for me. Very good explained and recorded. Congratulations.
Thank you I really appreciate it.
Just about to change the cam belt on 2006 2.0 JTD diesel turbo Fiat Scudo. Long time since I have done a cambelt on similar engine. Excellent lesson/ refresher.
I admire your patience to produce such a detailed video. Thank you. Excellent.
Thankyou so much mate i am glad you find it usefull
Did you have to undo the engine mount on the scudo?
@@CB19087 Top engine mount above belts. Yes. Just support engine first with jack under sump. Straightforward.
@@paulaspinall919 just had a look at it, would be much easier with that big mount out of the way. Thank you 🙏
I don’t know what you do for a living, however, if you ask me, I suggest you being a qualified mechanic because both your mindset and skill set are mechanic’s in nature. You are top notch bro. I love your work ethics!
Your comment touched my hart mate. God bless you and i wish you all the best in your future repairs
Just like to say a big thank you sir,Your video tutorials are awesome very clear precise and tobthe point with perfect step by step assistance . I have many french cars which I adore and often working on with much needed help and guidance from your videos . Today I done the Speedo colour change with the help of your video . Thank you so much sir awesome 5 star . Looking forward to seeing some new videos from you .
Thankyou for inspiring and really nice comment. Many more videos are comming very soon im preparing one 407 for this years Peugeot festival in 🇬🇧 and have tons of work to be done to it as i want to represent this channel with something special. I have loads of modifications for a rear and front lights comming up also i will rebuild a whole suspension so tons of more videos to come i am glad you find a videos use full. Nothing makes me more happy then people who apreaciate what i do.
Thankyou for finding the patience to prepare and complete this comprehensive video help, well thought out..
Thankyou mate i am really happy you found it usefull. I hope it helps many more people. My filming skills is not 100% but i do try my best to cover everything. I am currently working on a few new videos and hopefully soon they will be out. Please subscribe and you will be notified
Done x @@Mad4FrenchCars
Thankyou so much for this video, it has helped alot though my problem was the cam belt snapped, fractured 8 valve rockers, but I have replaced all 16. Need to set crank & cam timing, but this has shown me how to do that, many thanks for your time & patience in making this video 😊
I have been in your position then cambelt snap and I had to take a head cover off and replace all the rocker arms. That's why I like these engines is becouse they don't bend valves and worse comes to worse you get to replace a rockers I am gonna make a video on how to replace a chain tensioner and also rocker arms and hidraulic tappets in a future, unfortunately I have done rocker arms job long time ago and that time I didn't record . I am glad that my video helped. Make sure you stay around I am making a glow plug replacement video as we speak.
@@Mad4FrenchCars the rocker arms & tappets are easy old ones just lift out then drop new ones in, will valve clearances need to be done ?, nothing shown in the manual. Once again, many thanks
@@No-timeforimbeciles Hydraulic tappets so self-adjusting
Awesome video in fact the best well explained and brilliantly detailed video on UA-cam.
Thank you so so much for sharing this wonderful video full of info and very important advice. GOD Bless you 👍👍👍👏👏👏❤
Thank you, means a lot to me.
35:03 Great detail video mate Just a quick tip if you get a heat gun on the Bolt and heated up it comes off a lot easier and also what can happen sometimes is you can damage the threads inside the crank when you heated up this will not happen and it will come off a lot easier
Thankyou for a tip mate. I just recently used a blow torch first time on injector sleeve which came out with injector and I must admit it does miracles
@@Mad4FrenchCars It's amazing what a Bit of heat does the best thing about using the heat gun Is there is no open flame this way you cannot damage anything
@@bodgitandleggitgarage gonna try next time I do cambelt I think I have 2 cars to do in a next month
@@Mad4FrenchCars You only need to do it if they have threadlock on them
Following all your videos..
No words to praise you...
Thankyou mate i really apreaciate that.
Just one doubt..
What is the piece or sensor the car has on the top of the reservoir? Mine as only a small plug...
@@filipecosta7952 my one has sensor there but there is no connector going to it so i wouldnt worry to much. You mean coolant expansion tank right?
@@Mad4FrenchCars yes. 👍
Thanks for responding
What a brilliant video!
I've just been quoted £450 for the work so thinking I could try doing it myself.
I have citroen DS5 with same engine.
I do a lot of them myself my advice is check gsf car parts they had some decent cambelt kits for like 60 £ with discount. I have done 1.6 hdi 3008, 1.6hdi 508 and 1.6 Ehdi Ds4 in 2 days
Yes I've seen some kits for around £100
I'm giving this car all the love right now,
Just changed the whole front suspension on it but thought doing the cambelt is a bit risky and too big of a job to do on a drive.
Where are you located if you don't mind me asking
Excelente video amigo, asi de claro y detallado deberian de ser todos los tutoriales
Glad I found your channel mate, I just acquired a 2l HDI vitara so I'm scouring for tips! :)
I am glad you found it aswell. It's nice to be use full.
@@Mad4FrenchCars you realise your engine is mounted 90 degrees out? ;) ;) cheers for all the info!
56:26 That pulley can move by about 1 tooth. Peugeot use a "centraliser tool", it's U shape piece of metal rod, 1.4mm in diameter :) If you want to get it perfect without relying on something else!
It's half a tooth however, the author has marked the belt and locked the timing. Therefore the geometry stays the same. This is evidenced by the video of the key way being central once the belt has been correctly tensioned. (if it wasn't the adjustment would not be right).
The best Video I have ever seen. Top! Best Man!
Thank you.
Was lot of work mate ,but you're the best one, congratulations from Romania !You working like as ! All the best!
Thankyou mate i really apreaciate your nice comment.
To unscrew crank shaft bolt, why not using / block the brake pedal with gear in?
Good evening, is the distribution the same for the Volvo V50 with the 2L diesel engine? Is it the same engine? Thanks!
Hello Marian yes i believe Volvo V50 its exactly same engine.
hello I have a question. then when it locks the camshaft and crankshaft etc ... I install a new belt. Does the wedge have to be flush before installing the belt? my English is poor.thanks
Hi mate what do you mean by the wedge have to be flush before installing?
Watch the video till the end. Nice job man. Keep it going.
Thankyou very much for a such a nice comment i am working on a few new videos at the momment will be out soon.
Good work🏆 Explained very well for All to understand 👍
Thankyou so much mate i hope it will help someone to do the job i have tried my best to explain in every detail. ( sometimes a foreign accent gets in a way a bit but i do try my best). I apreaciate your comment it keeps me motivated for a future videos
@@Mad4FrenchCars It was the best Explained For the PSA 2.0 engine👌 I'm a amateur mechanic and feel confident i could now do my Cambelt and waterpump..Shame you ain't done a fuel filter video with priming and then cranking over as these engines can be troublesome
@@richiekaye1103 i will make a fuel filter replacment video in a very near future i am familiar with the issues. Like you said if there is an air lock somethere in a fuel system these engines simply wouldnt start but you just have to prime it while undoing a different bits all the way down to injectors and then it gets rid of the air locks i will deffinatelly make a video about it once i get hold of a new fuel filter for it.
@@Mad4FrenchCars Brilliant 👍 Look forward to it
@@richiekaye1103 i have made a Fuel filter replacement video mate i hope you gonna find it usefull.
Evening, me again, sorry, managed to get the tensioner in, did bolt up finger tight then tried to use hex key to tension belt, it is like tensioner is working in reverse,I turn the hex key & if anything it seems to be giving more slack on the belt, what am I doing wrong, wish I could show pictures to show what I mean, I am stumped
Hi mate is difficult to advise but use some phone camera or something make sure once again that tensioner is placed in a place correct as it needs to be finger tight 13 mm bolt as you did already but also one metal bit have to hug another little metal bit on a head. Tension itself is also weird as if you over spin a hex key then you loose a tension again I am not sure how to explain it properly.
Thanks for your video.. And about time belt and v-ribbed belt for citroen c5 2011.. Please
Awesome video champ!
Btw, I found a car at the wreckers that is the same as mine and has this engine and was wondering what you thought are the best parts to take from it. Most expensive to replace, I was thinking a high pressure fuel pump, ecu’s perhaps. What are your thoughts?
Injectors, high presure fuel pump if its a same fuel system as yours as there is a few different fuel systems. Turbo would be good but hard to get to.
@@Mad4FrenchCars great thanks champ, those Injectors are not cheap eh might get those first, the high pressure fuel pump looks extremely difficult to get to. Thanks for helping out. 👍
Hi, love your work! I tried to change the cambelt on my 2.0 HDI Volvo v50, but I messed up something because now, the crankshaft and the flywheel won't turn at all! I move the flywheel a little bit and after half turn it stopped. What could be the reason? Could bad positioning of cambelt cause the crankshaft to block?
Hi mate I think you need to do it again you should feel a hesitation then turning crank as the compression is there but it shouldn't stop totally
@@Mad4FrenchCars Thanks, I Appreciate the answear! The problem is, I removed the blocking pins, now the holes don’t match and I can’t turn the crankshaft to match them again. So How to do it again If I can’t block crankshaft?
@@robertszpua7884 hi mate really hard to advise without seeing it. I think that your timming is off so either a Tensioning or something went wrong. Check Tensioning pulley again to see where it sits an arrow should be in a middle of that U bit. If you remove a pins you should be able to turn the cranck back a bit to line the pin hole and if a camshaft hole is off then you can turn a camshaft with spanner a bit to line it up once a cranck pin is lined and cambelt off. It a sticky situation as you don't want to brake the rockers if you remove a cambelt and turn things individually. Should try to line cranck and then camshaft. Holes should line up every 2 engine revolutions
You're the best mate.
Thank you mate.
Hi, great video!!
What is the procedure if cam belt slipped 1 tooth and there is no refference to bring it back in place?
Thanks
Good question. If you have a cambelt slipped 1 tooth you should be able to stick 8mm lock pin to a flywheel and the camshaft pin hole would be off just by a millimeters so if you take of a cambelt and then put 17mm spanner on a camshaft bolt you should be able to turn camshaft by hand tiny bit until a 8mm hole perfectly lined up. Once lined up 8mm pin should be installed in to a locking hole. Then installing a new cambelt you would have to make sure cambelt pull is tensioned properly and a floating crank pulley sits right in a middle. I am sorry if that doesn't make it clear Its not easy to explain it without showing it
@@Mad4FrenchCars Thanks for your reply!
It does make sens to me .
I did comment on your video because so far I see there is an explination for every detail so that make it easy for people to understand procedures .
For example in my case I got a 2005 307 XSI 2.0 HDI 136bhp RHR ,I had problem with starting or it just stop by itself while driving, I had checked and change fuel filter and fuel lines,new battery , alternator and starter in good condition.
No problem with BSI as well .
I have no lights showing on dashboard.
So there is the point where I was getting confused and I asked some friends mechanichs ,they told me that the cam sensor or crank sensor are not reading well, I changed sensors ,the same story.
So I arrived at the conclusiton that timing is not lined up properly (does have symptoms of slipped tooth) but sensors wont be able to give a fault or check engine will not show in this case .
So I decided to change the timing rather than line it up as car has over 106k miles and I have no records that timing was ever changed. The problem now its that I dont have any markings for the previous position on the belt so I could find out from the tensioner ,and belt tension that was slipped so its the first case where I dont have any refference of belt position.
Thank you
@@cristiannitu5129 ya I fully understand mate
I noticed the crankshaft sprocket is loose around the crankshaft. The notch is 3 mm wider than the spline. See at 1:07:50 the sprocket is moved back and forth. Can this not cause a problem if not put back the same way?
Mate is called a flowting pulley. Watch a whole video i explain i believe before i put belt on a video
great video!
But how to lock the automatic gearbox? what gear to put?
I haven't done automatic mate so I wouldn't know. I know semi automatic also have a pin hole on a flywheel but if it's a fully auto with torque converter then I haven't come across one yet
Hi, it's me again, hope your cold is getting better. Are you able to confirm under the metal cam cover there is no actual gasket ? Is it just gasket sealant on the surfaces ? I have new gasket set for the plastic cover, but nothing came for the metal cover, I have bought a special grey sealant as I am inclined to think that is what they have used as there were no gasket under metal cover when I removed it ?
I am not gonna a lie I can't confirm but I can tell you from my own experience. So I know that sometimes there is a gasket going around injector holes around a middle. However I think if you properly seal it with sealant gasket you should be absolutely fine. Then I have done rockers replacement job on 2.0hdi I haven't used any extra gasket only a sealant and it was absolutely fine just need to make sure you seal it all up with sealant properly.
@@Mad4FrenchCars thank you once again, there was no gasket around injector holes, so I will just go with the sealant gasket, camshaft oil seal arrived today, but I made mistake when removing metal valve cover, I did not take out high pressure fuel pump, so now I have to do that to get cover back on, give me motorcycle engines everytime, much easier to work on
Sorry, do you know the torque settings for the camshaft pulley bolt, crankshaft bolt & the timing belt tensioner ? Thankyou
Crankshaft bolt it's 70Nm + 62°
Camshaft pulley bolt 20Nm + 50°
Tensioning pulley 21-23Nm
And that normal pulley under the engine mount is 56Nm.
@@Mad4FrenchCars thank you, though why they give the torque setting & then the ° setting I do not understand, why not just give the full torque setting ?. Metal cam cover is back on & torqued down, injectors back in, new fuel return pipe in place, tomorrow high pressure fuel pump to go back on along with the cam brake, then the timing belt & tensioner, & then just check I have re-connected all the electrical connectors, then turn the engine a few times on the crank bolt, dreading to actually turn the key, i do not want to do that lol
Hi mate. Great video. Really helpful. Can you tell me how many miles can we run with a need cambelt please? I bought one and they replaced the cambelt 48000 miles ago. Thank you
Hello the cambelt is good for anything between 60k - 100k miles or 10years for original cambelt and 4-6years for after market cambelt as even original cambelt after 10years starts to crack. Also it depends who replaced it also a brand of a cambelt. Normally i replace every 100k miles but i do 100k miles in around 18 months.
Saved me 400 pound 😊😊
I am not looking forward to the tensioner bit, I have phone with camera, but will have to look at instruction to get the view like you did, I am not good with hi tech gadgets, weather has hindered me alot last few days, lots of snow & sub zero temperatures, only possible to work 2-3 hours before fingers & toes freeze, warm up & go out again
I know the feeling mate. Tensioner bit is not as complicated as it looks in my video, you will be Ok mate.
Thank you for this great video, two questions, i noticed the bottom crankshaft sprocket moves on the the keyway as if the gap sitting over the keyway is too big, even with the flywheel and camshaft locket the sprocket still moves on the keyway how did u over come this issue.
And finally does the fuel pump need to be marked up for timing?.
Kind regards Jay
Hi Jay please try watch video again I have explained why crank pulley is moving the way it does, it's becouse its a flowting crankshaft pulley hdi engines have that to help with a cambelt instalation, then you put a new cambelt on you pull crankshaft pulley to one side so then you tighten a cambelt it goes right in a middle and little pin has a free play indicating you done it right.
@@Mad4FrenchCars Thank you i shall watch again, does the fuel pump need to be timed?
Kind regards Jay
@@jaykent6645 no Jay fuel pump is sinned by one of the 2 camshafts it basicly spins more then you rev more therefore provides more fuel presure
@@Mad4FrenchCars i didnt get your name, but just want to say thank you so much for all your kind help and hard work in bringing this video to us all.
Kindest regards Jay🤗
@@jaykent6645 my name is Arthur. Pleasure is all mine. I am glad it's helpfull.
Someone asked how to line both pin holes but i cant find a comment anymore. So the holes lines up every 2 evolutions of the engine just keep spining your engine clockwise using a bolt on a crank and while watching a camshaft hole. Once camshaft hole ends up in a correct place then flywheel pinhole should be in a correct place to
Camshaft spins 2x for every revolution of the crank, it's why the timing pins only fit in once every two revolutions.
@@khalidacosta7133 100%
can i make just one sujestion sir , oh great viseo by the way , BUT , i see people do this all the time when undoing a bolt , they tend to pull up on the bolt , expending a lot of energy doing so , had you took the socket and breaking bar to the other side , and push down to release the bolt , it is much easier to push down that to pull up , example , you would never pull up to release a wheel nut , you put a breaker bar on it and stand on it using body weight to release it , same thing applies to all bolts , push rather than pull .
Thenks ameizing work
At 1.24 hours, that little thing that looks like Woodruff key on the crank is tight, it does not move at all, I have not fitted tensioner yet, will it free up once tensioner is fitted ? Also I am having problems lining up the three holes for the bolts that hold the top engine mount
Yes that little pin on a cranck should go to the middle of that little space once you tension a tensioner. I wouldnt worry about a engine mount holes until you done your cambelt
@@Mad4FrenchCars many thanks 👍
@@No-timeforimbeciles my pleasure mate
@@Mad4FrenchCars camshaft oilseal arrived today, opened it up.........it is the wrong one, double checked the one I ordered from eBay, I ordered correctly, the have sent wrong one, have messaged seller & tell them I want correct one by express post, possible another two days waiting ☹️
@@No-timeforimbeciles sorry to hear that mate hopefully it comes quick
Молодец ,хороший метод👍
Thank you mate.
When you got the left over piece of the crankshaft pulley out, did you replace with an after market pulley, as the new one you showed very quickly was not same as the original ? Did you use the original crankshaft pulley ?
I can't remember but I think I used same one
I think I did use a same one I took off but I am not sure I might have used one from another engine but then I would off been used one aswell.
@@Mad4FrenchCars so it does not matter it was two pieces ?
Sorry to bother you so much,
@@No-timeforimbeciles in the bigining I thought that it was broken becouse it was 2 pieces but I have install 2 pieces and it was OK.
Awesome bid man
Could you please give the parts numbers you replaced I've found it hard to do a match with my engine since mines us a DW10TED4 RHR and most parts I've found are for DW10BTED4 RHR and don't know if they are the same or why or what is the diference having same problem with headgasquet and thermostat housing I blew my headgasquet and want to replace all at same time
Hello and thankyou for your comment let me try to understand something. You need to have a look again as i couldnt find no info on DW10TED4 RHR as it should be DW10 then it should be one letter and then TED4 RHR. However DW10BTED4 RHR is a common engine with a common rail, turbo,16 valve and catalyst converters. The best way to always do is then you order parts use your registration to get a correct parts. But i will try to get you a part numbers. Cambelt kit came as a set.
@@Mad4FrenchCars i would appreciate that information as I am having problems obtaining the ''right'' parts if it helps you my chassis number is VF36DRHRG6L000879 and I'm looking for the headgasquet, thermostat and waterpump kit
dziękuję za film
pomógł mi
I am glad to hear that.
Hellow,it is this engine the same la volvo v50 2.0 diesel?anyone can help me with this doubt?thanks.
Hi mate from what year is a car ?
Yes i have just checked and looks like volvo v50 atleast from 2005 -2010 deffinatelly used a same engine like in this video.
2008 and thanks for answer.
Good morning again, I think I have a major issue with the crank, I can turn it with the old crankshaft bolt I have put in, but there is no free play on the crank timing pulley & the Woodruff key will not move at all, any ideas ? Please
So you have put a cambelt on and then you try to turn engine by hand clockwise the cranck woodruff key wouldn't go towards a middle where it suppose to be? Have you tension it properly? Have you done any marking on a belt to make sure you put it in exact same place as a old one before doing it? Maybe it's out by one tooth or something can you make 2 full evolutions of engine with cambelt on?
Where are you located are you in UK?
@@Mad4FrenchCars I am afraid I am located in southern France. Yes I put the new belt on, the two dots on the camshaft sprockets were in correct position discoloured links on the chain were in correct place, cam pulley was pinned, flywheel was pinned, took out locking pins & turned the crank on the bolt 4 times, tried to put locking pins back in, they would not go in, I think I have made mistake again, I did not put on chain tensioner, now when the camshaft is locked in place the camshaft sprocket marks are not aligned, chain must have slipped, so I have to take metal cam cover off again & do it all again. But even so, the crank timing
Pulley is solid no play in it at all, I saw yours moved quite freely without belt on it
@@No-timeforimbeciles you deffinatelly want to have a chain tensioner installed before even trying to turn engine by hand. So now you will have to line everything up again unfortunately. Then you line everything up I mean cam and cranck then install a pins back in and remove a cambelt again. Sometimes you need to pull cranck pulley off and check that little pin as it's sometimes can be just a bit stuck in place it should be loose
@@Mad4FrenchCars yes I know, at least I had not torqued down the injectors, had left them finger tight, & rather than take all 4 fuel leak off pipes out, I have just disconnected the one supply line & taken injectors out with leak off pipe attached, but I have all those 8mm bolts to undo that hold the metal cam cover & I threadlocked them ☹️ Should the crank timing pulley be easy enough to get off, is it held by anything ?
Thanks man
Getting that crank bolt out, was not half as easy as you made it look, & the piece left behind the crank pulley was not easy to get out either, I have to get a new crank ring sensor as I stupidly tried prising it off with a large screwdriver & a piece of the outer edge snapped, but purely my mistake
We all do mistakes mate cranck bolt is always gonna be a pain to get out becouse it's a big bolt and they put that cement thing on it so that it wouldn't come out. We all make mistakes I fought I am gonna snap a glow plug today my hands was shaking. Not always things go to plan I try my best to show a process as it is but sometimes I have to film a scene like 5 times couse I said something which I didn't mean to say. So some bolts I have already undone before few times as I repeated a scene but most of it is raw and natural.
@@Mad4FrenchCars I looked it up, that "cement" is close to superglue which activates on tightening. Peugeot reccomend heating the bolt up to ensure it doesn't snap!
@@khalidacosta7133 ya the cement is quite a strong stuff. I would try to do a bit of forward and backwards action. Turn it tiny bit anticlockwise and then back clockwise. As you could see I didn't heat it up and it came out fine but I wouldn't be able to say 100 % that it's gonna work for everyone.
Thanks
My pleasure mate
I tried for two hours to get the tensioner even in place, you must have smaller hands than me, could not even get it close, not being able to see I think is main problem, will try again tomorrow, did you get a child to fit it lol
You can try to put a belt on crank and camshaft and idle pulley and then put tensioner in place. I actually have a big hands but I managed access was horrible.
@@Mad4FrenchCars will try that, as you say access is horrendous, all I want to initially do is to turn the engine on the crank a few times before I try the key, thanks once again
@@No-timeforimbeciles ya you deffinatelly want turn it over by hand before you start it.
Don't need to remove the starter you a hole right above the hole you showed that is on the engine wheel.. You can block your engine like that without removing everything
U Made that look so easy 👍🏻👍🏻🤣
It wasnt as hard as people may thing but i am not gonna lie it is quite a job to do if you havent done it before. It does take most of the day
You better dont use a screwdriver to lock the flywheel. It is always better to lock the crankshaft with the 2 pieces of special tools to avoid big problems.I have seen many times broken pieces falling down. ( Tip of the screwdriver enz...) Some guys using the thoot blocker only en then complaining that its breaking. Of course its gonna breake because it is to small to do hold the force alone. The 8mm pin and the thootholder togetter will do the job without problems
Good video. But what’s the point of marking on the gears ⚙️ & old belt when there’s locking pegs 😂😂😂?
Good point we'll its just a little reassurance to know for yourself that you didn't skip a tooth then tensioning and that everything is exactly same place like it was.
Even with locking pegs some people still manage to put a cambelt in a way that they miss one tooth becouse of flowting pulley on a crankshaft in place there is still a tiny play where you can miss a tooth then doing a cambelt up. Don't get me wrong I don't really know how but there is a people I know who have managed it. So it kind of give a extra safety option to mark the belts and teeth up. Some people think they done it all right but they actually missed a tooth and it will run just not as good and belt is not gonna last as long. And if the belt goes before its time then rockers will all snap in half in a best case scenario and then it will become head cover off job.
@@Mad4FrenchCars I agree, it's an excellent visual confirmation everything is in the right place.
@@DA-oy7zp thankyou mate good to know I have like minded people. I think then doing a job like that there cant be to much of a reassurance.
hi.my friend.i have a car same as you.i got a code P1351.Do you know what is going on?thanks!
Hello my friend. Fault P1351 is a pre/post heating relay circuit. Which basicly means your glow plugs or glow plug relay is gone. In UK 90% of 407s have that fault but it doesn't really affect anyone as there is no real winter here so no preheating needed. But in a cold country it would cause a problem with starting. To get rid of your fault you need to replace glow plugs and if that doesn't fix a problem then need to replace a little glow plug loom too.
Hi mate which engine code it is your engine
Спасибо !!!
Do you know the engine code?
Yes mate the engine code in this video is DW10BTED4/RHR very common engine in loads of pugs and citroens i think they even used it in few older volvos
@@Mad4FrenchCars thank you
@@erikgaler2778 My pleasure mate
And which year is your car?
My engine code is AH03
DO YOU THINK THAT IS THE SAME ENGINE.
IT IS A 16 VALVES, 2.0, 4 CYLINDERS, 130CV.
YEAR 2017
Thanks for your video
This video is done with 2005 Peugeot 407 2.0hdi
Engine code is DW10
Procedure on a AH03 would be very similar as the engine is very similar, unfortunatelly can't advice as I haven't worked on one yet
What a detailed video! Great job. Just wondering why you need to mark the belt against the pulleys? I think as long as you lock the crank shalft and flying wheel, it does not matter how you put on the timing belt later. Do I miss something?
Yes mate its still possible to skip a tooth on a belt if you put it without marking its just a extra precaution to make sure 100% that you put it on exactly same as it was. If you skip 1 tooth then a work of engine will be different and cause problems.
@@Mad4FrenchCars Ah, that makes sense. Extra warranty of intactness. Thank you.
Another question: in the case the cogs slip during the process, how can we restore the correct position?
Hello !! fantactic video , can you tell me the funcion of this ? www.jjherrero.es/chaveta.jpg ,
Is it dangerous if I turn the crankshaft sprocket by hand? I see this tab scroll right left , Thanks very much !!!