i have encountered similar problem, but there is small difference, and may problem was when ever i switch on the controller dse8610 immediately it say fail to stop and i didnt start the genset just power on the controller and generator is similar the one u did the video. any suggestion about where fault came? thanks benz.
Fail to stop did you try to change config or no if now thin check your oil sw its having wrong comfig or if you have deepsea configurat connext to the module go to digital input and chnge it yo close to active and safety on delay
@benzblogsVlogs no I did not change, although may oil pressure sensor is a single pole sensor it does not have switch. But I will check configuration and get u back.
my dse7310 control module fail to change module modes, according to the manual. "if a digital input configured to Panel Lock is active, changing module modes is not possible. what should I do to deactivate the digital input. thank u
Good day sir,bakit po yung dse 6110 nmin sir pag crank ko start xa tapos pag off nag starter sumasabay din ang sa fuel solenoid kaya ayaw tumuloy ng andar.. salamat po.sir sa tugon..
Yes sir ganun nga po pag cut ng starter sumasabay din ang fuel..tapos crank rest 5 seconds,then crank ulit nag on din ang fuel sol. Subasabay sa pag cut ng starter..
Iba ka talaga idol ang husay mo .thumbs up idol ingat jan
This is my Best chanel l learned
Thank you sir bless you
Boss u make WhatsApp group where we can share our problem & discussion best channel for learning... Thanks
I have only facebook group i dont have whatup but u can message me
i have encountered similar problem, but there is small difference, and may problem was when ever i switch on the controller dse8610 immediately it say fail to stop and i didnt start the genset just power on the controller and generator is similar the one u did the video.
any suggestion about where fault came? thanks benz.
Fail to stop did you try to change config or no if now thin check your oil sw its having wrong comfig or if you have deepsea configurat connext to the module go to digital input and chnge it yo close to active and safety on delay
@benzblogsVlogs no I did not change, although may oil pressure sensor is a single pole sensor it does not have switch.
But I will check configuration and get u back.
@@abdiazizmuse567 send me pictures too
hi i got more knowledge from you, after that can you please give us one lesson about meccalte uvr/avr
Ok sir no problem
Thank you dear
Welcome
Sir may VLOG ka po ba ng mga location ng sensor sa Diesel generator???at Kung paano ito I inspection at i troubleshoot?
Meron sir sa shorts ved
my dse7310 control module fail to change module modes, according to the manual. "if a digital input configured to Panel Lock is active, changing module modes is not possible. what should I do to deactivate the digital input. thank u
Yes becuase it is lock de activate forst the configuration in the module ao you change the mode
@@benzblogsVlogs thank you sir, and how do I deactivate the digital input. thank you very much.
can I message you in messenger?
Yes sir noprob
Q1 two wire of stop solenoid +&_
Contunio like this video sir
Thank you
One of my questions is will you have generator business worldwide.reply me
Yes
I tried to pull out the positive of the battery then the unit is shutoff is it normal?
Yes its normal
Mostly to the digital controller
Ok n master monitized k n...
Solinoid po vah ang sira sir ..or adjust lang delay.?
If not start the generator and you get the voltage from the soleniod connection thin soleniod is defective
Ok sir... E try nku og test tom.. thank kaayo sir?..
Watching master monitized k n may add k n.
Bless u master
@@benzblogsVlogs salamat master
@@HowtobyKuryentecianTV salamt sin sayo sir
Good day sir,bakit po yung dse 6110 nmin sir pag crank ko start xa tapos pag off nag starter sumasabay din ang sa fuel solenoid kaya ayaw tumuloy ng andar.. salamat po.sir sa tugon..
Ganito gawin mo check mo mona from module kong ang fuel ay ng cut and supply pag ng cut din ang starter doon mismo sa module output from digitalnout
Yes sir ganun nga po pag cut ng starter sumasabay din ang fuel..tapos crank rest 5 seconds,then crank ulit nag on din ang fuel sol. Subasabay sa pag cut ng starter..
@@reidtubechannel kong pwedi mo matignan ang config or program check mo ang number sa module para mkita mo anong naka config baka start hindi fuel on
Ok sir thank you so much..
Ok
Hi idol, how about yung hindi maka-start yung generator engine at "failed to stop" yung alarm. anu kaya possible trouble? thanks Idol
Pag fail to start lodi pweding battery issue, pweding fuel intake issue, pwedi g walang supply ang ecu or fuel soleniod
Sir gud day..pwedi mangutan..failed to stop .alarm sa among generator sir ..peru wala na ga andar.
Kong di namatay sir yong engine pasabot lang na wala moagi og relay ang suply sa fuel soleniod
Or kaha na rectahan ang soleniod ng suply wala maputol pag time nga imo nang ipastop ang generator
Maong dili mamamtay
Ok sir.. tan awon nku ugma.. thank you kaau sit
Chekupa ang imong soleniod bc stackup lamg sa kadugay
Boss Anu kya issue Ng ds510 controller ayaw mag stop
Pag ayaw mg stop dalawa lang yan ither oil sensor or sw and my problima sir check mo
Boos ano problema sa deepsea module nawala ang screen display
Sir pag nawala ang sxreen display pweding lcd ang sira or marumi lang ang rebon sa loob pwedi mong tangalin at linisan
@@benzblogsVlogs ok boos salamat
@@benzblogsVlogs boos nag alarm yon bago nawala ang display..msc data error alarm
Sir kong msc lang ang alrm di dapat mawala ang display magshutdowm lang yun dapat communication yun ng ecm mo at module
@@benzblogsVlogs boos pano troubleshoot ang msc data alarm
Anong trouble bakit failed to stop?
Did you watc the vedio till end