Відео

When I connect my pc with device using usb cable, It is not showing anything. It says Com4 inaccessible. I tried manytimes but cant connect to device with usb cable.Any solution?

Watching friend, good evening, nice sharing

Sir how are you, I want to ask you one question about generator, I connect the cable from generator to low voltage switch board for auto pourpose but after that the generator is not starting and it's saying ECU data fail and ECU override sir please could you tell me the reason why my generator is saying like that

I have a Honda EV6010 generator Max Output 6.0KVA, Rated Voltage 120V, 50A, 60Hz, Single Phase. My controller is dead and I have been through two replacement controllers one used and one (supposed) new?. No new controllers are available. So I bought off Amazon HQM611OU 0.5-70V. Will this Smartgen work with my existing Automatic Voltage Regulator? Will it send the DC voltage that my AVR needs to keep up with AC load?

Good job lodi

Ang laki nyan lodi

Atos lodi dami nyan

Nice one lodi❤❤❤

Loss of Mag- PU what does it mean?

Watching kabayan, good evening

Iba ka talaga lodi Ikaw na❤❤❤❤❤

Hi, my dse7320 mkii keeps restarting, I turn it on and after 30-60 seconds it restarts. I'm afraid to update it because there's a possibility it will restart during the process. What do you advise me to do? Thanks

Great subject, But you need to show the part when you're talking about it. Also where is the program you're talking about???

Please i have an issue on my Perkins 4000 series Heinzmann Actuator, when on the ignition instead of Actuator to move anti clockwise as oppen it will move to clockwise as in off, the spindle will be very strong in off position. But when off it from battery supply it will be free, and move both directions. So could be the problem?

Watching w/ ads kabayan, nice sharing, sending support

Hi, tnks for u video, i have a question ple answer me🙏, in my 4012 one of the governors dose not work, mechanic say ecm has problem, what can i do?

Can you please explain why 3 pole breakers are use for synchronization applications insted of 4 Pole. In my country they use 4 pole breakers. (When a generator in off status, it fully isolated from the live bus including N)

If not get resistance is faulty ??

Ikaw na talaga lodi..❤❤❤❤

Hello my boss thank you for the video we appreciate...can you please one do a video of how to test a generator using a megger tester?

Hello boss i have this EPG electricaliy powered governor and it not controlling the engine

Good job lods

Cool!!!

That's a great information

❤❤❤

Thanks

Nice lods morning

What are s2,3 and ScE in motorized wiring and where to connect the aux in dse module and its programming

Ok yan lods ah

Great job thank you brother.... Correct password... Big thanks from Algeria....

Hi Chief engineer, I have a 20kVA generator controlled by a Smart Gen controller and I'm not familiar with this controller, and I want to convert the 3-phase output to a single phase. Can the controller be reconfigured to handle the winding setup using the front panel buttons? I don't have the software program. If possible, please guide me through the process.

Daming generator sir Benjie,maymikaniko Rin Po ba kayo Jan?

Mine is a deepsea 702k and it's starting the gen set in auto mode when power is on and it does nMine is a deepsea 702k and it's starting the gen set in auto mode when power is on and it does not go off. What might be the problem? 7:43 ot go off. What might be the problem?

Mine is a deepsea 702k and it's starting the gen set in auto mode when power is on and it does not go off. What might be the problem?

I used to monitor my generator fuel on dse controller that is. Engine>>fuel level and get like 70% or 20% but yesterday when checking level the dse was showing xxx what could be the problem please update

Hello sir I enjoy you videos here in Kenya but I have a question . If the fuel level was showing on the date scree. But it failed to shoe like in the last 3 days what could be the problem

Hello boss...away from this please...i have an easy gen 1500 woodward ...every time i try crank it displays "crank protect"on the screen nd it will not even crank even once...how can we solve this please?

mr. i need sofware deeo sea 6810 email mr

mr. deep sea 8610 calling aplication solution mr

Hello dear sir. I need help .. how can start generator. Everything okay. But im change new penal.Auto start controller 7210.. please i need help

Good tutorial lods Ang galing mo talaga pag dating Jan salute sayo lods Ikaw na talaga

mr. unit model code8610mk11 model varian0. harderware varian 5 firware file is modelcode8610 mk11model variant 0hardware varian 0 version cek please mr solusion

mr deep sea 6810 mk 11 sofware

just watching how to set up fuel volume sender. is there a pressure sensor that can doe this , my tank is 1.2m high but just 300 ceiling clearance in acoustic container. Or a distance sensor suitable for deep sea?

mr. flasing deep sea 7320

Good day po Sir, may I ask what is the cause of the powerwizard controller with a model: EMCP 4.1 of our genset has no display?

Hello , Where do I download the software from? It's not on the site ! can you send it to me ?

Say Generator one more time please!

Lods gandang gabi

❤thank you