Maytag Centennial Washer Error Codes and Reset - How to Find & Fix Maytag Centennial Washer Problems
Вставка
- Опубліковано 1 жов 2024
- This Maytag Centennial Washer Won't Spin - or so a customer said. When we get any of these style washing machines in our store, the first thing we do is plug it in and check for Maytag Centennial Washer error codes to see what is exactly wrong with the machine. This helps us quickly figure out what components could be causing the issues, then fix them.
In this video, we're going to tackle a few issues through diagnostics, and you'll also get the entire Maytag Washer Error Code list, too.
Parts Links for Major Failure Points:
Shift Actuator (F7E1, F7E5): bens-appliance...
Washplate Hub: bens-appliance...
Lid Lock (Maroon-Colored): bens-appliance...
Other Less Common Parts: bens-appliance...
Some things tackled in this video are:
Maytag centennial washer problems
Maytag centennial washer manual
Maytag centennial commercial technology washer
Maytag Centennial Washer reset
Maytag centennial washer not spinning
Maytag centennial washer error codes
Maytag centennial washer won't spin
Maytag centennial washer won't start
Maytag centennial washer won't drain
Maytag centennial washer won't spin
Maytag centennial washer won't start
If we missed something in this video, let us know in the comments, and I'd be happy to try to help you out!
Tools I use in all videos can be found at my Amazon Idea Page: www.amazon.com...
Did this video help you out? Send me a tip, and help me make more Appliance Repair videos for people to watch for free!
PayPal: paypal.me/Bens...
CashApp: $BenjaminSchlichter
Affiliate Disclosure Form: bit.ly/3oXeu3B
** Links to external websites and parts may result in me receiving a commission on sales
Having had a 32 year career as technology teacher I appreciate the clarity with which you presented a complex system and allowed time and opportunity to observe and absorb. Thank you for helping so many. Keep up the good work.
Thanks! I have watched numerous videos to determine what is wrong with my Maytag and how to fix it myself. While I appreciate all who have shared their knowledge, your videos are by far the most useful in my opinion. Your explanation, screens, and pace are all fantastic. I want to thank you and show some support. Sharing your knowledge and experience is a tremendous help to those of us on our own.
TY
I recalibrated many times & wouldn't start. I can't pull Washer out bc I just had surgery.
This morning I prayed and recalibrate and it's washing
TY and I pray for you 😊
Washers and dryers should not have error codes. Removing the unnecessary electronics being used will fix that problem for good. Go back to the reliable and simple electrical systems, get many years service and reduce the cost!!! All experienced electricians and electronics techs ALREADY KNOW THAT!!!!
Wonderful video !!! Originally I got ripped off by the appliance repair guy from Sears who came over to check the washer . He ran a two minute self disagnoses and said it would cost over $600 for a new control board to repair so it wouldn't be worth fixing and gave me a 10% off coupon to buy a new one at Sears and charged me the $79 diagnoses fee . After watching a few of these videos I found out it was the actuator so I bought a new one for $25 and now the machine works perfect. Sears pulled a total rip off scam to get you to buy a new one. I complained to consumer affairs but they said it's legal to scam and cheat consumers and they really don't so anything down there but collect their government pay.
This is what I like is someone who explains even the little things. I didn't even know the manual was inside the washer, kind of silly place to have it. I had already downloaded it and now with this video I hope I can diagnose the problem and fix mine.
I had already unscrewed the latch and noticed mine is spinning and starts fast then stops and the high agitator speed doesn't seem to be working. Not sure if it's the capacitor or something else. Sounds like the agitator at 1st also isn't in place or off if that makes sense and I checked the screw and it is in tight real tight and its hard to even unscrew so I can't check to see if spindle is worn if that's even the wording.
Thanks again for the tutorial and wish we could nominate videos for awards because this and all of yours deserves one for content.
My sensing light stays on and the lid lock light blinks.. that’s not under your codes ? :(
Mine too!! Cant find an answer for this 😢
Did either of you find a solution?
@@demielizabeth18 The best code I could make out was a basket fault. I changed out the shift actuator and was able to wash 2 loads. Then it did it again. I ordered a new cam replacement. When I put it down to replace it I realized the belt has frayed and come off, was also very loose to begin with. So I ordered a belt. After testing the actuator with an ohm meter it reads good. Sigh May have only initially needed a belt. While I was at it I removed the wash plate and cleaned. Inspected the tension rods because I have the jet engine sound when spinning. No rocking and moving across the floor. Just LOUD. The new belt has produced a sporadic squeaky sound in addition to water underneath. I have been confident that the bearings were shot to begin with. When I initially texted a repair shop with my symptoms, they said they didnt think that was the issue and I would have to bring my washer to Them! Did I mention that Im a stubborn, 4’ nothing, 65 yr old blonde? 😂 Tomorrow Im expecting a transmission casing. I relate this to Johnny Cash and his one piece at a time Cadillac song 🎵. Except its more than a dime. $285.00 to be precise. Haha Trial & Error, process of elimination.
@@demielizabeth18 Being the REAL ZIGGY that anything that can go wrong will, I should always go with the worst of the 5 codes that are listed. The Smart machines arent very smart or there wouldnt be 5 to 20 possible fixes!! 🤬 Needless to say my Maytag Centennial and I have been spending a lot of quality time together! I vaguely remember the elaborate space and workings of a wringer washer in action but oh how I yearn for the simplicity and reliability.
@@demielizabeth18 replaced the transmission and its working like a Boss now!!
Fixed! My washer apparently was stuck in sensing mode, because when I cleared everything back to factory default, presto, it works as it should. I had an appt scheduled for this Monday for a repairman. $95 trip charge, $25 per quarter hour labor, plus part. I was looking at roughly a $175 repair bill. Not anymore thanks to you. Much respect.
You do a Great job with this video! I was able to fix our washer with your shared Knowledge. The only problem I had was getting it out of the "calibration/demo mode" I ended up unplugging the washer and held the on/off button in for a minute, plugged it back in and it worked. With your code diagnostics and viewing a few other videos I was able to make a semi-educated guess at what the problem was. It did turn out to be the actuator. I had thought I received the wrong part through "Sears Parts Direct" and brought the new part to an appliance parts store because it didn't match the part on my washer. I was told the part had been replaced with the black plastic version even though they did not look similar. It was true, and the part I had received did fit and worked.
Hope this may help others too.
Hey man this was very well done thank you so much! Honestly I had no idea a washer was so complex. I've used bits, bytes and nibbles to diagnose giant crazy expensive machines but never knew it was how I was going to get trouble codes from my washer. I know this video will help lots of people and we all thank you for making it. Hope you're staying safe and thanks again!
These style machines have some EXTENSIVE features that let you basically test everything and know what's going on to fix them 90% of the time before you actually take a single component apart. Its a little bit.... Complex... To get down, but we deal with these machines at my used appliance shop so much, we just plug them in with electric anymore, and do a pre-screen diagnosis so we can figure out exactly what it needs before it moves down the line for refurbishment, because that 5min test can work out junk that could take a solid hour to figure out by just running the unit.
jjjjjkjkjjjkjjjjjjjjjjkjjjjjjkjjjjjjjjjkjjjjkjjjjk
0⁹0nly o90999999999999999999999999999⁹
Well done! It's heartening to see young people who know their stuff. Keep up the good work!
WOW! I work in industrial repairs and have watched so many videos of all kinds. This is definitely the best! Your details and information are so well presented, great camera work and SOUND (so many videos have horrible sound!)!!! I feel very confident that I can now address whatever is wrong with my Centennial (the very same model as yours). Thank you so much, and if you found this video and have a bad washer, watch and learn!
Excellent!!!
Thank you so much. We call Maytag repair and we're told there was no reset. You saved us $1k ( which we did not have!) You are my hero today!
Very good video, was a life saver, I ran the codes, couldn't quite figure them out, ran them again, no codes, is spinning like it should! Wife was hoping for a new washer! Not now!
Gotta say this video was extremely helpful in getting my neighbors washing machine up and running tonight as he just picked it up earlier as a used unit that was supposed to work but wouldn't do anything when he got it home. Running through the diagnostics and the reset got her back up and running despite my lacking an entire understanding, but if a fumble wins the game I'll take it.. 😉 thanks for this one
These videos are extremely helpful. Thank you for taking the time to do them. They are so easy to follow and understand.
Wow this is honestly the best, and most helpful video I’ve ever seen!! Awesome job!
?? My 9 month old Maytag is not agitating the drum moves but the center won’t move anyone know why?? I removed the Basket Driven Hub it looks good I called manufacturer they won’t have someone out here till November
Much appreciated! Didn't know if my Maytag had a diagnostic mode...but it did. I was able to decipher the error codes and have a mode shifter fault. It's stuck in spin mode and will not agitate. Thanks for the video! You saved me a lot of $$.
What if your lights flash orange-yellow not green? Drop kick it out the door and never buy another Maytag?
omg i hate washing machines like this 😂 ours won’t wash like it doesn’t complete the cycle so i’ll try to help my uncles with it! but oof i hate technology. i just don’t have enough patience for them. this info hurts my brain tho 🤯😅🤦🏻♀️ but thank you for the video! i just wish my uncle didn’t buy this version because so many people having problems with this one oof 😓
Thank you for your tutorial, Ben! It's a couple days before Christmas (2020!) and I'm having trouble with my washer. Its timing couldn't be better! Sheesh!
Hope this helps!
@@bensappliancesandjunk can you help me with my washer?
Well played. I know this video took you a long time to make. I’ve considered making this video but you have done a much better job than I could have ever done. I bet you are going to see this video take off over the next few months.
I did a video similar to this back in January and its my #1 video so far. But it doesn't include all the extras between the manual/auto tests and recalibration... I figured that now, 9 months later, I've learned enough to do a better, more complete video on this, so I took another crack at it. There's still more I can do better at on this, but the views/watch time is better than the last one, so I'll take it.
I did the video mainly because I really liked Sears' video on the Kenmore VMW, but it just has how to get it into diagnostic mode, nothing about what all options you have, or the error codes themselves.
@@bensappliancesandjunk do you have a way I can contact you? I have some serious questions about mine!!! I have a similar model, just no agitator inside.
@@byronvontreal7046 should be on my profile for email
@@bensappliancesandjunk This is Maytag MVWC415EW.
Hands down the best, most descriptive how to video on washing machines. Thank you sir.
Thank you for this video! You saved me about 1000$ !
Excellent video homie !! it made it really easy for me to fix my washer 👍🏼👍🏼
I have this Maytag washer and normally when washing a load the lid locks , senses the load , spins a few times , then starts to fill with water to begin the wash cycle. Now the lid does not lock and is stuck in the sensing mode. I was having trouble getting in to the diagnostic mode but will keep trying and would appreciate any help on why the lid does not lock and why it is stuck in the sensing mode.
Hi, I am having the same problem with mine. Did you solve it?
I will appreciate your help. Thanks.
Sorry. No I didn’t resolve the problems. The family didn’t want to wait and just bought a new washer from the navy exchange at at discounted price
I used the access to the fault codes and was able to restore the washer to functioning properly. I didn't have to replace anything, just clear out the Fault codes. We were almost ready to buy a new washer. Thanks
This helped me so much the only thing different is my buttons are yellow and I have an extra cycle. But this saved me a washer service call thanks. 👍
Best utube illustration video I've evere seen👌bravo!
Not sure if I'll ever have a chance to use this, but it was fascinating to watch.
Same
I have this same washer. My washer will not work automatically. You have to manually set the knob on what ever setting you desire for it to perform the desired setting. It will not continue to perform a complete wash
Your videos are the best, clearest, and most complete repair videos I have found. Really excellent. Only one thing, I have my Maytag drying now as I pulled tub, hub, and cleaned everything before I put in the new hub and put it back together. What I haven't found are any mentions of grease, silicone, etc when putting the tub back over the shaft. Do you recommend any lubricant/seal grease when putting things back together? PS Your video on the recalcitrant agitator was so REAL! This is my 3rd hub replacement and it was rough getting the agitator out. Hammer, dowel, hard steel hooked probes and a WD40 soak finally worked but my wife was already pricing a new machine. (Maytag Bravos - MVWX655DW1, 8 years old. (3 hubs, 1 actuator so far)
Using this video to diagnose the problem AND run the recalibration, I fixed my washer! THANK YOU!
At first I thought it wasn't spinning. I came to UA-cam and found you "washer not spinning" video. I went into the error codes and found a code that was not in the video. Then I found this video and it was the drain error. I ran the auto test, then the manual test, and the washer spun but did not drain. I found the part on Amazon for $25! It came next day, I installed it, ran the recalibration cycle, and IT WORKS! Thank you so much!
Great job explaining this, as it’s NOT an easy thing to do for most homeowners; and even us Techs, can have some “troubles” IMO, as diff companies have diff steps for diag mode, and some still; haven’t updated the codes listing for older/current machines.....making things a bit “annoying” (which means ur in the iPhone with The Company’s Tech Support, &/or you are Googling the diag code number and seeing if get a bit on some site; heck, may even be lucky and the manufacturer has the code in their site😉).
So, again, IMO, did a fantastic job explaining diag modes/codes so that most ppl can follow along and understand if you are not a service repair tech👍🏻👍🏻
Cheers✌🏻
You lost me at how to read codes with the flash lights , list a longer time, or just a video on that is needed.
The codes are found in the technician manual.
You can also read the transcript 😊
@@marilynkamakea9323 didn't load
Thank you for this!!! I have a lot of error codes, most scary though is the motor fault. I’m no handy woman but I’ll see what I can do on my own 😰
Motor fault means the motor won't run properly. There are two main things it can be:
1) The motor is bad, or the electricity isn't getting to it. Check the connectors, and test the motor w/ a multimeter.
2) The capacitor that is underneath, near the motor is bad and its not jolting the motor w/ electricity when it needs to, to help it start. Look for physical defects (like something popped on the inside), and test w/ a multimeter.
There can be other things, but we had #2 happen on a Motor Fault at my shop a week ago. Stumped my tech and I told him "Just check the cap real fast". 5 minutes later, the machine was running fine because we replaced the $20 capacitor.
I finally found and stopped at a diagnostic video that is complete. All the others were very vague, incomplete and the narration resembled that of an auctioneer!
Thank you! 🤠👍
I have the same washer. It has begun to sound like an airplane taking off in the spin cycle. Bearings?
Bearings likely but I'd check underneath the unit where the plastic wheel is. Sometimes that will rub on the bottom of plastic protective housing and cause awful noises too
@@bensappliancesandjunk mine sounds the same, except i have the impeller type . . can it still be bearings too ???
Hi. I have a Maytag Centennial Washing Machine. I watched your video and ran my washer through the diagnostic. I am getting error codes: E1, E2, E3, E4, E5, E6, E7, E8, E9, E10, E11, E12, E13. What does this mean. There were no "F"-based error codes.
Then you are reading it wrong or it's not a centennial like this machine and has a totally different error code system.
My washer has been having issues draining. I was able to get it to drain and do multiple loads and it happend again. Now I cannot get it to drain and get to the diagnostics. Any help ???
Drain it by hand with some plastic containers and I bet you'll be ok to get into dx mode.
@Shari T thank you. I got it to go yesterday. It's been a few times now where I've had to unplug it for awhile and Mayne even a few times just to get it to drain but once it starts it drains and is in its way. Only had errors for slow drain and unbalanced load. I emptied it and did a calibration and erased the codes. Here's hoping 🙏
@@NewfieVortex Hope it behaves for you
! i changed my shift actuator [washer wasn't agitating; but would spin; that seemed to be the consensus for the fix] and now i've got error codes for the motor also! Ugh!
may end up calling an actual appliance guy...which is what I should have done in the first place...
I went through this step by step no lights come on. And machine still humming
Same 😢
Mines won't go into diagnostic mode whatsoever. Stuck on sensing. Very frustrating
Thanks for the video, but these washers suck. I had my previous one for over 10 years until it gave out, this one is only a couple years old and already on the fritz
Right? The fact that we need to pull codes from a washing machine tells me “there’s too much tech here.” Wish I at least had the one that has an agitator. That came out literally months after I finally bought washer and dryer for home.
Amazing video man. Thank you for sharing your knowledge!
MY WASHER SOUNDED LIKE A JET PLANE YESTERDAY TO DAY IT SOUNDS LIKE GRINDING WHEN SUPPOSED TO BE DRAIN AND SPIN MODER HELP
I want to thank you for your helpful videos, but I'm afraid my Maytag (MVWC465HW2) must be possessed. When it went down, one of your videos led me to a bad shift actuator. Ordered a new one (from you), cleared codes and recalibrated, and it started shifting between modes. But during the spin cycle, it would make a loud whirring sound, then give up trying to spin. I took the clutch assembly apart, and there was nearly no grease. I cleaned, re-greased and reassembled. Cleared codes and ran the calibration mode. Everything worked in calibration and it threw no new codes. Tried to run a load through it and it went back to making that noise and giving up on spin. Through every repair effort, the code has been F0 E5. Rods are good, unit is level, and the load was small and balanced. It always calibrates fine without throwing a code, but fails when you try to wash normally. I'm about to toss this POS out in the yard.
I'm slow/so.this series 100HE stopped with water full.
After trying to scoop it empty.
I checked/removed/straight wired/tested for cap.correct value ea.of these.The pump motor,the shifter thing/allready mentioned, the run cap.
And,the lid switch/ which I busted disassemble rather than sliding it off.
All I probably need was the knowledge of how to RESET?
I bought a new lid switch/ installed it and it locked shut!
Flashing lid light.I forgot,at the beginning of trouble I had a display of Fill light on.
Anyway I busted the new switch/ gently trying to pry it open with a small screw driver.
The washer thinks it's still spinning/ filling I'm guessing.
I didn't understand how to clear all codes/or reset this thing.
Got another lid switch coming.
Mean time/I'm using old faithful/my ol Kenmore HEAVY DUTY SERIES 70 WASHER.
Rufffffff get the 2 in and out by myself but?
Thanks!
I'll watch again but ,with my disability.It was beginning to look like WHEEL OF FORTUNE to my mind.
It was near the end of the video that you stated something I had never heard nor consider- after changing a part that effects the electrical system, recalibrate/reset the CB. Fantastic. Thank you.
Its extremely overlooked. The computer board doesn't magically *know* what situation a new component is in. Was the shift actuator in agitate or spin prior to replacement? The lid lock? What wash cycle? So many small things that the system assumes is true/false and it won't be able to conjure the situation until you force the machine to reset.
Phi u[ou ioo stew
Thank you for a wonderful video with excellent explanation and not talking to fast. Very well done.
Thank you, still having problems but did manage to reset. You give very clear instructions.
I have a Bravo model of Maytag and it would spin out of balance. I just changed the suspension rods and that solved the problem for about 5 washes. Now it's out of balance again. I did the re-calibration and the Spin light stayed on and blinking. Any advice?
Hello, ok. i have this washer on your video. I replaced the door latch switch, and now I'm getting NO POWER as if the washer is unplugged all together, only the green light behind the control board is on. Any solutions? Thanks......
My machine goes straight from sensing skips wash and goes to rinse.
F7 E6 Motor Fault 🤬
I know those are expensive as it's the heart of the machine. I'm just buying a new budget mechanical washer. They have Maytags on sale for memorial day for $550.
i leave my lid lock like that permanently..got tired of having to wait for the machine to unlock the lid so i could throw in that last pair of underwear i forgot about when i started the load
Thx. My Whirlpool WTW4816FW2 top load washer stops during wash and gets stuck in sensing mode=blinking sensing light. I have not been able to reset and or enter diagnostics with water in the machine. If I MT the water it appears to allow me to enter reset and possibly diagnostics. Question is do I have to MT the water again to enter diagnostics? Does this indicate a specific bad part? Thx
What does it mean when the spin and lid locked light stays on constantly. I just unplugged the washer for over 10 minutes but when it's plugged back in the spin and lid locked lights turn on without any other input Also, I think it gives a F7E5 code but the the other lights being on make it confusing
Worst washing machine I have ever owned and the last one I will own! Complete garbage design! If I knew now what I do now I would have rebuilt my old Whirlpool that lasted for over 20 years without one issue. Repair man came and could not get into diagnostic mode. Board issue. You see a Maytag aka Whirlpool pass on it!!!!
What if code shows just F on and off? Does that mean no codes?
Yeah my washer is doing the same thing when I test it for error codes the sensing light flashes but nothing else. And it will only run water and hold the water, but wont do anything else.
I've got the same washer,, 3yr old already rusting around the inside lid,, looked online and complaints of same thing ,, used cheap paint ,, not baked on like old style ... Cheaper is not better ,, thanks Lowe's and China...
According to your explanation, it should be F2 and F3
According to your lights showing .
What is showing and what is being said look like two different things so I am confused
Completed diagnostics on my Maytag Centennial and got the F7E5 code. Which is the Mode Shifter Fault. Should I replace that Shift Actuator?
Maytag SUCKS!!! They used to produce quality products that would last decades! Now they SUCK!!!!
I try to go into the manual test but then nothing happens when I select the code for heavy agitation. To clarify, I am selecting the manual mode as seen, then pressing start, then moving the dial until the "Wash" and "Rinse" lights are on, then pressing start. All of my lights aside from the locked light, flash green then nothing happens. Anyone know whats up?
My lid does not lock. I have a Maytag electric washer I bought from Lowe’s. I had a power outage and it suddenly stopped working but I’ve only had this washer for two years
You said E and F ,
there are no other letters, so how would you add the other letters up to get your code?
There are six slots, so there are six lights ,
ABCDEFG ????
What numbers or being added? ??
This makes no sense
This washer is a pain in the butt with the load balance,constantly have to balance the load to keep the washer from shaking out of control ! Does anybody else have this issue? Otherwise great washer. However I have been able to get past the lock, by using drummer tool to cut plastic away on lock switch on base part of the switch! Because of having to open washer to hand balance load , don’t have to wait or fight getting door to unlock.
your Sensor light blinks, then two lights blinks , then two lights blink again ,but your code says 4,2,1, so it doesn’t make any sense
What am I missing here?
Don't bother with repairs, you'll frustrate yourself as this garbage continues to break down. Better yet, throw it off a cliff. Worst pile of shit washer along with Samsung.
I have a maytag commercial technology top load washer. It fills during thr sensing mode then drains all the water out. Then it does nothing. I replaced the shift actuator and the pressure tube seems to be ok. Can you point me in the right direction?
If you could get 5 years out of any new washing machine anymore, you're lucky. They're all junk with too much electronics. That goes for water heaters too.
You don’t turn counter clockwise all the way around you just do left right right right left right
I always show going counterclockwise so it starts from the 12-o-clock position, so mapping everything out is vastly easier to show others.
Yup worked thanks
I’ve been repairing appliances for close to 40 years … those Whirlpool/maytags are a a waste of time just even driving out the customers home !!!
Unable to get into diagnostics. Unplug washing machine, then after plugging it back in the spin indicator light comes on. I press and hold start button to cancel, light goes out but performing the steps to enter diagnostics is unsuccessful. Any tips?
The sensing light flashes yellow/orange and wont spin/drain at all on mine. Tried to put into diagnosis mode but doesnt work. Lid does lock and unlock as normal.
Hi..i got this centennial from a storage...no error codes...when i run a cycle it does a few minutes of sensing ...then agitates a bit then goes into wash mode...lid unlocks...and does nothing...its been in wash (wash green light on) mode lid locked light off for 20min not doing anything..not agitating....no sounds at alll...like its in idle mode...any ideas?
So what fixed the machine...cuz it's showing E7E6....just like mines....
Hi , i have combo Maytag washer and dryer .When i press start botten the solenoid opening water in the second i take my finger away from start botten it's stop working please advise Thanks.
Completely useless to me. Successfully entered diagnostics mode but then nothing but the sensing light flashing on and off-nothing else. I have no idea what this means.
I have a Maytag century with a basket speed sensor fault. When I ran the speed sensor test and spun the basket the other lights flashed while the basket turned. Can I assume the speed sensor is good. Any other ideas. Thanks on advance
I have this washer and its 5yrs old. The unit is beginning to make a screeching sound that gets louder as the rinse/spin cycle winds down in speed until it stops. Just after it stops i reach in and turn drum and it screeches a bit while its still hot but after an hour i reach in and it dosent screech and turns fine by hand. I suspect something worn between the drum/tub and shaft. I cant find a drawing that shows the parts that might be causing this, any ideas?
I want to go back to the 70s and the 80s when my mom had the same washer as when I was born until I moved out in my twenties..... Crap is garbage now
Video was very helpful. Easy and clear instructions. Thanks for all the time you put into this.
Can someone please tell the synchronous motor and the plastic pieces inside to stop breaking?
I'm getting real tired of this little piece breaking
I have checked all the codes cleared all the codes, the washer fills up goes into a wash cycle and then when it comes time drain nothing happens, doesn't seem like there's anything sending a signal to the pump to turn on the hose is not clogged will drain on its own with gravity
So mine was different. The lid lock was flashing and it was humming/grinding sound. Then it shut off
the one your at right there talking with is actually mine is commerical, and it is smelling and i did all the cleaning solutions etc. does mine have a filter and where is it? please help me i think mine is 2018 washer machine
Hey Ben, I don't have a machine problem at this time. The main reason for my comment is to tell you your videos are great and I hope you have continued success. I just bought a new machine and was trying to research it. Anyway it looks a lot like this one. I'm guessing it's probably the same with a different name. Conservator vaw3584gw. I'm 67 yrs old and give up on finding an old style built to last machine. This one cost me 799.00 delivered. I hope I can make it last. We have laundry for 2 people. Emanuel County GA
I'm back a year later. I didn't remember making that comment. Anyway the machine works well but I needed to recalibrate it. Why does it get out of calibration?
mine shows f7 e1 ..... it will do everything but spin when it tries to spin it moves a little bit then kicks off then lid lock light starts flashing
Every time I try and start my washer the lid lock light flashes and won't do anything else
Usually that means the lid lock is shot, or the striker that goes into the lid.
But the lid is locked
It's starts to sense the load then it stops and the lid lock flashes
@@lonfilipovich65mines kinda does the same. And I can't get it into diagnostic mode either
I don't know what I'm doing wrong. When I finish turning the dial, I hear a click but nothing happens.
I used the heck out of this video. I have the exact same one and this was very helpful, especially with all the codes listings etc
Glad it helped!
Mine show's me no error code and the problem I have even if I put it on deep water or sensing it always put 2 or 3 inches of water
My centennial fills with water, then the fill light flashes and it does nothing. If I wait a certain amount of time, the lights will go out and it will drain the water again.
When I checked error code, only the fill light flashes.
When I set it to automatic checks, the lid doesn't lock, and the basket doesn't spin. It fills with hot and cold and I believe I hear the agitator moving, but no spin. Idk what to do.
From what position on the selector wheel do you start when you put the machine in self diagnostic mode?
(backwards maytag logo on video) GATYAM
what if after I unplugged and plug it back in before I do the combination the sensing fill light is blinking
I have the same machine, it's stuck on rinse. it fills back up after draining all the water.
Junk i HATE this POS.Didnt fix mine. All mine does is click and hum.
Washer won’t spin on wash cycle but when knobs on drain and spin it spins clothes any idea what’s the problem thanks
Do you have anything on lock mode mine is blinking on locked. Won't do nothing. Won't even open I had clothes in side