Це відео не доступне.
Перепрошуємо.
How to Make a VU Meter Without IC and Transistor | Reactive Lights Circuit
Вставка
- Опубліковано 9 тра 2021
- How to Make a VU Meter Without IC and Transistor | Reactive Lights Circuit
A volume unit (VU) meter is a device displaying a representation of the signal level in audio equipment. Especially in speaker's output.
Materials Needed:
- 10pcs 5mm LED lights
- 10pcs 1k ohm Resistor
- 10pcs IN4007 Diode
- 2pcs 16V 2200uf Capacitor
- copperwire 0.2mm
- wires
- Speaker
Subscribe to my channel and click the bell button to be updated on my next video. Thank you for watching♥️Enjoy and have a great day.
Subscribe to this channel: / javiersdiy
Related DIY videos:
DIY RC Car from Cardboard:
• How to Make RC Car Fro...
DIY 12v Power Supply:
• How to Make 12v Power ...
DIY 13000 mAh Powerbank:
• How to Make a 13000 mA...
DIY Sander Disk from Old DVD/CD player:
• How to Make a Mini San...
3 in 1 Power Supply:
• How to Make a 3 in 1 P...
DIY VU Meter:
• How to Make a VU Meter...
DIY Face shield:
• How to Make DIY Face S...
DIY Tester:
• How to Make Test Light...
DIY Flashlight:
• How to Make Emergency ...
DIY RC Car:
• How to Make RC Car Fro...
DIY Generator:
• How to Make Generator ...
DIY Air Cooler:
• How to Make a Powerful...
DIY Water Pump:
• How to Make Powerful W...
DIY Air Pump:
• How to Make an Air Pum...
#VuMeter
#VUMETERCIRCUIT
#DIYVuMeter
I'll try ... Ty
Thanks for sharing this video watching from dubai
Thank maam. Keep watching po
This is cool, thanks for sharing 💕
Thank you sir. Keep watching
Tutorial yang sangat bermanfaat sekali lanjut berkarya mas Joss👍
for better understanding please use the universal language
Hello , I liked the project , I built one and it was excellent ; I put a 10k potentiometer on the signal input to regulate the brightness of the leds, it was really worth it. thanks .
Yes sir. Thank you also
how to install the potentiometer?
Circuit diagram please
Keep it upd congrats kasi nabalik na yan
Salamat sayo boss.
Bom muito bom
Dear Sir,
You have a discrepancy between the video setup of the vumeter , and the circuit diagram. In the video you have 4 diodes on the left, and 4 on the right- hand side. On the circuit diagram instead, there are 5 diodes on the left, and 4 on the right -hand side. Which one is the correct circuit ?
Thanks and regards,
Paul
Nice bro
Thank you bro
Watching from Ormoc City
Thank you sir
@@JaviersDIY welcome
good job
Thank you sir.
What is the range in watts of speaker you used? If ever I want to connect it in 150W-200W speaker should I used also the same component just like in the video or just change the value of capacitor?
yes sir you can connection it directly with that output power of the speaker
Good👍👍👍👍👍🤗🇮🇩🇮🇩🇮🇩
I like it
Thank your sir
Gostei muito do projeto e quero copiar um para mim. Dúvida: quantos watts está alimentando o circuito?
for better understanding please use the universal language. Thank you
@@JaviersDIY i did the project and It turned out amazing
Hola! Lo hice y quedó muy bien. Una pregunta. Porqué solo me prenden 2 luces? Será Porqué coloqué capacitor de 100 omhs?
For better understanding please use the universal language
Brother can we use it in high rms power amplifier as 600 watt amplifier board
Yes sir. You can use. This one
Mantab
For better understanding please use the universal language
Tem como ligar um lado em cada canal do amplificador estéreo?
For better understanding please use the universal language
Does the audio shown there go through an amplifier or just the cell phone?
Amplifier sir. As you can see it doesn't need an supply voltage to run where as it is directly connected to speaker or the amplifier
Whit 10led left - right is good?
Yes sir
If i will connect this to a 300 watts amplifier,do i have to change the value of capacitor?
Yes sir. You need to change it.
@@JaviersDIY thank you sir..
Watts value of capacitor change
input subwoofer or full range?
Full range sir
Can i use 8404 amplifire module for this ?❤
no sir.
@@JaviersDIY ples make for 5v amplifier module❤
Por que tenho que usar um diodo para cada lâmpada?
For better understanding please use the universal language
En ningun momento aclara la POLARIDAD del diodo donde pone las resistencias, como si todos lo supieramos
For better understanding please use the universal language
@@JaviersDIY ????...Well, then ask UA-cam that your videos ONLY BE SEEN in countries that use the "universal language" Please.... !!FOOL!!
Circuit diagram please
In the video sir
😎🇵🇭👍🏻🍻
Kalau pake 20 led ba gak bos?
For better understanding please use the universal language
Bhai iahse amplifier to karab nahi ho jayega
for better understanding please use the universal language
Input diode problem
I am not clear on the polarity of the capacitors. Nor where is it soldered or connected to the amplifier. A diagram would have been a thousand times better.
Pengen beli
For bettery understanding please use the universal language
where's the min, Mr.?
Kalau pake untuk tape bisa tdk ?
For better understanding please use the universal language
@@JaviersDIY can i use that one for the tape radio ? ... I wanna to make that one for my tape...
@@satryaadiputra yes sir
Input
Não é legal! Os leds piscam praticamente iguais! O interessante é ter um funcionamento escalar!
For better understanding please use the universal language
@@JaviersDIY Is not cool! The LEDs blink practically the same! The interesting thing is to have a scalar operation!
Diagram problem undo
Input diode problem
The diagram I make sir is correct, maybe you have wrong connection in your project, just check it sir
Diagram plz...
In the video sir.
Where the + and -
did you view the the video sir?
@@JaviersDIYwatched it, but I didn't find the positive and negative poles
You can determine thr every side of the components
See a capicitor - and diod is +
Kurang jelas
For better understanding please use the universal language