This is the most awesome video for laser box making!! Your explanation of the kerf is invaluable. Your idea of making the fingers longer and sanding them, make these boxes look much better and more professional than the average laser cut box. The average box with the burns showing just look cheap and slapped together. I truly enjoyed your sense of humor and your soundtrack was amazing. Thank you so much for making this video!
Long time woodworker, but I just ordered my first laser cutter and am watching lots of videos to see how to translate from one technology to the next. This was a very good one and demonstrated that only the tools have changed. Thanks
It's fascinating watching the workflow of other people using the same tech as you. Like, because of the cutters I use, I don't take the kerf into account as much, because it's so small. It means that I can cut all four sides of a box in one line, sharing the finger joints, which (if done in a way that compliments the overall design aesthetic of the build) can look very pleasing without the sanding step. You just have to make sure that they feel solid. I think that's where a lot of beginners (and a lot of people on the internet too) go wrong, and make the fingers really wide, so the boxes don't ever fit together properly and feel really flimsy. That's the worst kind of laser cutting.
Every time I have seen a video about making boxes using finger joints the person always directs you to some box generator on the internet. Where is the fun in that? Especially when it is so easy to design your own in LightBurn. The first box I made turned out perfect. I didn't even have to glue it together. By far, the best box making video I have seen.
I think this is one of the most satisfying videos to watch! 😊 If you're a little ocd, (like me) I like everything packed in a nice case in my workshop. Alas, not everything is available is a box, but with my new cnc router and newly added laser, I see some box making in my future... Nice video!
Besides the kerf, there is also the defocusing effect which, especially on thicker wood, can make the joint taper from top to bottom. This can be partially remedied by refocusing the beam and moving slightly closer to the wood surface until you find the sweet spot with minimal deflection.
Excellent video, thank you. I usually apply the 2 in. yellow frog tape across the burn area especially the engraving portion. It greatly reduces the burn flare and is easy (but tedious) to remove.
Interesting tips...I've made some but I left the charred edges on the fingers. I think I'm going to try making some like you did here where it looks more like it was cut on another machine. The graphics/animations were great!
FYI, if you up the pressure of your air assist on your laser you'll get minimal or no residue and less burn. Get the air above 20 PSI. Thanks for the great videos.
It highly depends on what plywood (or wood) you're using though. This specific plywood is dirty as hell, I have another 3mm plywood that lasers super cleanly, with no soot and the edges are nice and brown, not black and burnt. Would've used that but 3mm is slightly on the thin side for a box.
Thanks for this! I really appreciate the information on accounting for kerf on the laser.. I'm trying to make some puzzles, and keef is definitely causing problems!
4:35 “You need to offset by the width of your kerf”. As the laser tracks along the cut line, it removes half of the kerf width on either side of the cut. To compensate for this, you should move the cut line away from your part by HALF of your kerf width, not the entire kerf width.
Yes, I missed a word. In reality it’s a little more complex than that though as exactly half the kerf may still be too loose, or too tight, and you’ll have to adjust it a fraction in one way or another. Hence the need to cut test pieces. But please continue beating the dead horse rather than reading the comments about it already made.
Thanks for this. I started some laser finger joint box goodies a couple days ago. Wait, is google reading my mind? Whatever, great video. Now I need to get my belt sander up and running...
Except it’s plywood and it’s dimensionally stable. What you say would’ve hold true if this was solid wood but plywood doesn’t have the issues you speak of and glueing in is just fine.
This will be very useful. I'm currently looking into using laser cut sheets of the following chipboard, laserboard, Basswood or MDF for building HO scale brick structures. I've been playing around with off sets in the CAD model to get reasonably tight fitting joints that don't go together too tight. Of course part of the problem is I'm using a 15 watt diode laser cutter. Chip board and Basswood cut just fine. In the end I'll probably stick with 1mm or .045" chipboard as the bricks scale out at 1.7mm/.046" from the centerline of the mortar joints. This way when joining wall sections in a row or at 90°s the courses of brick line up. Off course on CNC machines depending on direction you can just specify the offset amount via the tool directory with G41 and G42 for left or right hand compensation.
Amazing video! The editing on this was excellent, and I enjoyed all the visual puns and gags. I never got proficient enough in Paintbrush to find the 3D CAD features, but maybe that's unlocked by the paid professional license. It's nice to see you back! I was checking your channel a few days ago to see if there were any signs of life that I missed notifications on.
There is life, but creatively there's not all that much going on. Best place to check in what's happening is instagram. I'm in between workshops right now, so I don't know when the next video will come. Hopefully not too long.
You totally can cut circuit boards on a laser cutter! Well, you apply a layer of something like spray paint as an etching resist, burn off the paint in the inverse of the pattern you want using the laser cutter, then etch away the exposed copper with ferric chloride. Might make an interesting video actually
you can reduce or even eliminate soot and tar markings on wood by putting a layer of masking tape overtop of the wood. you can eliminate checks from where the laser cuts through the wood and encounters the blades or honeycomb table underneath by putting the wood on a sacrificial layer of non synthetic cloth. i use muslin since i have tons of it.
Don’t like the masking tape method myself, especially on a little rougher surfaces it tends to pull up grain and not seal properly leaving a gummy edge that still needs to be cleaned up anyway. If I’m going to sand the surface anyway (which I am) it’s really not a big deal to remove the soot at the same time. You can also eliminate those bottom marks by elevating your piece a little using shims, but that does require a pretty flat piece to begin with. Since mine was warped I had to weigh it down to keep it flat.
That's a nice box and a lovely box joint! I had no idea you could carve such deep and good grooves with a laser. Cool! Now pardon me while I go howl your name at the moon. Hope it's okay that it's summer, not winter here at the moment.
Tip for glue up: add masking tape to the areas where there will be glue squeeze out, this will make cleanup a lot easier and faster. When the glue squeezes out and is starting to get gummy you can remove the tape and it should leave clean edges.
Yes, there's a reason I didn't do this. The plywood was crap quality, and masking tape pulled out wood fibers out of the surface when removed. I'm honestly not all that worried about glue squeezeout, especially if the joints will get more work done, or if they're in a place where it won't be seen or affect the end result.
Funny, when I lived in Stockholm years ago I made wooden cases for all the Abene and Bahco machinists tools I’d acquired. Still going strong 30 years on.
100%! I can't believe it's been over a year already! This year has been mostly kind of a blur. I was really looking forward to Maker's Central at least, but who knows when that will take place. Events like that are so important to all of us creators who only really see each other online otherwise.
didn’t know you could accurately cut slots like that with the lasercutter, nice! you could have used that to cut a recessed thumb slot into the lid for easy opening : )
I had the same question. If your laser cuts exactly on the line then it should burn away the same amount on each side so the amount that needs to be adjusted should be half of the total kerf. I guess with material like wood it could be fine because it is somewhat flexible but acrylic on the other hand would possible struggle if you don’t get it exact and even 0.5mm could make a big difference. Especially, if you have many small finger then the excess material could easily amount to a few mm.
Yes it should be half of the kerf or close to that. Wood is quite flexible so you might want to make it tighter on purpose for a snug fit, but more rigid materials would benefit from being offset to something closet to the kerf/2
If I could offer some suggestions. Sand your whole blank before cutting. I like to use painters tape. Saves a lot of time cleaning up that nasty carbon. Or a little alcohol on a rag works great to remove the carbon, however, I've been experimenting with Clorox bleach and works better than alcohol but wear gloves because you won't get that smell off your fingers. Use rubber bands to help with the glue-up.
Don’t like sanding the whole board before cutting because that ultimately just leads to resanding stuff away anyway. The painters tape can help, but I find depending on the wood it can pull out grain from the surface, so I tend to avoid it. It doesn’t really take much time to clean up the soot anyway.
I just stumbled across this video. Very well done! I have seen people use transfer tape on both sides of the wood to eliminate the soot and need to sand the pieces. Before I purchase a roll and try what are your experiences?
I am just starting out with a laser cutter. I will definitely look for the online box template. When you draw in Paint, how do you get the drawing over to the cutter? I am using Lightburn.
@@RoamingAdhocrat oh, 1-bit animations have been around since that time too for sure. You had even quite action filled games, racing games like Grand Prix Circuit, which was fully 1-bit and full screen moving gameplay, back in the 80s. Or of course my favorite from the era: Shufflepuck Cafe.
I'm sure that I'm missing something, but why do you offset all the box joint surfaces by the width of the kerf? My (often unreliable) intuition suggests it should be half the kerf.
My stepson and I have lasers. Very good video. Did you do the editing and FX too? How did you get that great accent? Where are good 3.4mm, 4mm wood sources in USA? Thanks.
Your video helped me a lot, thank you so much mate. I'm planning to start my on small business in beekeeping and I would like very much to have your recommendation on which is the best laser cutting machine would be suitable for me to make Langstroth Beehive boxes made of 20mm thick Pinewood and Cedar Wood with finger joints shape. Thanking you for your kind feedback in advance and best regards...
the bamboo wood I'm using has some flex to it (it doesn't lay flat), any tips on how to clamp them so they hold well? I'm creating a L-shaped divider for my partner's box
It’s inconsequential. As long as you weigh the board down so it lays flat when cutting any little twist still remaining in the small pieces will easily be corrected when gluing the box together.
@@SwitchAndLever ...until you cut something that has a long side, which bends out of the flatly clamped-down stock as soon as you cut it, and your laser optics promptly crashes into it at high speed first time it tries to fly over it.
@@SwitchAndLeverYou just did so yourself, and tried to shrug it off as no big deal - except that's exactly the point: bent stock IS a big deal, even if you can clamp it down flat. You can't have it both ways. "It's inconsequential" until the first piece rises way up after being cut.
Another great and thought provoking video - thanks. I have neither the patience nor the laser cutter to make such strong joints and the "beauty of the joint" doesn't interest me so much, so the question for me is - how do you figure out the minimum number of interlocks to make so that the strength of the joint matches the strength of the material being used?
I am not a material's engineer, though I find using a finger size that matches the thickness of the material is a good starting point. The glue joint will be stronger than the surrounding wood for sure. If you're using other ways of cutting your joint, like with a table saw, you could even use the width of the saw blade as the width of your joint, as it will make things significantly easier. If you use huge fingers the joint won't be much stronger than a butt joint, just easier to assemble, if you use a massive amount of tiny fingers the joint becomes difficult to assemble and glue.
shouldn't you offset by half the kurf? I mean the laser follows your dimensions and cuts both ways but I'd assume you'd only care for the part that cuts into your work piece.
This is the most awesome video for laser box making!! Your explanation of the kerf is invaluable.
Your idea of making the fingers longer and sanding them, make these boxes look much better and more professional than the average laser cut box. The average box with the burns showing just look cheap and slapped together.
I truly enjoyed your sense of humor and your soundtrack was amazing.
Thank you so much for making this video!
Long time woodworker, but I just ordered my first laser cutter and am watching lots of videos to see how to translate from one technology to the next. This was a very good one and demonstrated that only the tools have changed. Thanks
How much did it cost
Love the graphics on this one!
Thank you, glad you like it! They were lots of fun to make 🙂
I love the graphics, humor, and his accent!! Just got yourself a new subscriber!! 😁
Love the graphics well done. IT 30 years and took me back (Windows 3.1)
@@SwitchAndLever 2:55 how did you make this one?!
I'd like to click an extra like button for the 3D Paint features and the sweet, soothing soundtrack!
I just got my Ortur Laser 2 (7w), This is a fantastic video. It is well produced and very entertaining as well as informative. Well done!
Fantastiskt bra video! Mycket underhållande redigering från början till slut. Lärorikt dessutom. 10/10 poäng
Nä minst 12/10
Tackar 🙂
It's fascinating watching the workflow of other people using the same tech as you. Like, because of the cutters I use, I don't take the kerf into account as much, because it's so small. It means that I can cut all four sides of a box in one line, sharing the finger joints, which (if done in a way that compliments the overall design aesthetic of the build) can look very pleasing without the sanding step. You just have to make sure that they feel solid. I think that's where a lot of beginners (and a lot of people on the internet too) go wrong, and make the fingers really wide, so the boxes don't ever fit together properly and feel really flimsy. That's the worst kind of laser cutting.
I already knew most of this stuff but I stayed for the charming animations and great cinematography. Subbed!
Thank you! Very informative and helpful, it its supportive for my decision to acquire a Laser Machine now. Thanks !
Great info, and the graphics were entertaining. Thanks!
Loved the “Don’t go ham on your sanding comment” awesome video and that box with the retro graphics turned out amazing.
Every time I have seen a video about making boxes using finger joints the person always directs you to some box generator on the internet. Where is the fun in that? Especially when it is so easy to design your own in LightBurn. The first box I made turned out perfect. I didn't even have to glue it together. By far, the best box making video I have seen.
Because they're useful tools. Even if it's just to get started and then you can modify it. Time is $, and any minute saved is worth it.
I think this is one of the most satisfying videos to watch! 😊 If you're a little ocd, (like me) I like everything packed in a nice case in my workshop. Alas, not everything is available is a box, but with my new cnc router and newly added laser, I see some box making in my future... Nice video!
thanks. I'm a Starrett fan as well, I'm going to do the same for some of my older tools that don't have boxes anymore :)
So, so well made... the video as well as the box. The Paintbrush reference, EGA style editing, etc ... fantastic.
Not EGA, not even CGA, it's just good ol fashioned 1-bit color. Thank you! Glad you liked it 🙂
I've been waiting for a video like this for 8 years, time to upgrade my boxes
Besides the kerf, there is also the defocusing effect which, especially on thicker wood, can make the joint taper from top to bottom. This can be partially remedied by refocusing the beam and moving slightly closer to the wood surface until you find the sweet spot with minimal deflection.
Super nice box! Great tip on extending the fingers/ sand flush. Gives a really clean appearance.
Excellent video, thank you. I usually apply the 2 in. yellow frog tape across the burn area especially the engraving portion. It greatly reduces the burn flare and is easy (but tedious) to remove.
Haha, i wish i had found this Video when i Was struggling through that phase.. thank you ❤
Thank you so much for the tutorial, this is exactly what I’ve been looking for
Interesting tips...I've made some but I left the charred edges on the fingers. I think I'm going to try making some like you did here where it looks more like it was cut on another machine. The graphics/animations were great!
Box looks great, I really like how you too the extra time to make it nice. Excellent laser tips as well!
Thank you for posting this! Very clear cut information!
FYI, if you up the pressure of your air assist on your laser you'll get minimal or no residue and less burn. Get the air above 20 PSI. Thanks for the great videos.
It highly depends on what plywood (or wood) you're using though. This specific plywood is dirty as hell, I have another 3mm plywood that lasers super cleanly, with no soot and the edges are nice and brown, not black and burnt. Would've used that but 3mm is slightly on the thin side for a box.
@@SwitchAndLever True, a lot seems to depend on what glue and how much glue is used in making the plywood too.
Welcome back, you've been missed. Cool box, look forward to hopefully seeing the level again and some of the recent flea market acquisitions.
Yes, I have restoration videos planned for the future, but I'm in between workshops again so who knows how long it will take to start doing.
onf of the best video for absolutely beginners :) Thank you!!!!
Thanks for this! I really appreciate the information on accounting for kerf on the laser.. I'm trying to make some puzzles, and keef is definitely causing problems!
Very well presented. Precise and instructive. Well done.
I just wanna say how much awsome you re...great tutorial, best so far I watch !!!
4:35 “You need to offset by the width of your kerf”.
As the laser tracks along the cut line, it removes half of the kerf width on either side of the cut. To compensate for this, you should move the cut line away from your part by HALF of your kerf width, not the entire kerf width.
Yes, I missed a word. In reality it’s a little more complex than that though as exactly half the kerf may still be too loose, or too tight, and you’ll have to adjust it a fraction in one way or another. Hence the need to cut test pieces.
But please continue beating the dead horse rather than reading the comments about it already made.
@@SwitchAndLever Hey S&L, don't let internet comments get to you, focus on the positives? Glad to see another of your videos, very magic looking box!
This was brilliant. Exactly what I was looking for, thank you!
Thanks for this. I started some laser finger joint box goodies a couple days ago. Wait, is google reading my mind? Whatever, great video. Now I need to get my belt sander up and running...
Well explained, to the point video. I am looking forward to make my own box 👏
Wonderful!! Just what I was looking for! Thank-you for your excellent video. 👍🏻🤗
Great video thanks for sharing, had fun watching and learned something to boot.
Good stuff --- A little preparation with mask goes a long ways to final product cleanliness
One thing I would change is not glueing in the bottom. Wood swells and shrinks and a floating bottom would prevent the box from warping over time.
Except it’s plywood and it’s dimensionally stable. What you say would’ve hold true if this was solid wood but plywood doesn’t have the issues you speak of and glueing in is just fine.
This will be very useful. I'm currently looking into using laser cut sheets of the following chipboard, laserboard, Basswood or MDF for building HO scale brick structures. I've been playing around with off sets in the CAD model to get reasonably tight fitting joints that don't go together too tight. Of course part of the problem is I'm using a 15 watt diode laser cutter. Chip board and Basswood cut just fine. In the end I'll probably stick with 1mm or .045" chipboard as the bricks scale out at 1.7mm/.046" from the centerline of the mortar joints. This way when joining wall sections in a row or at 90°s the courses of brick line up.
Off course on CNC machines depending on direction you can just specify the offset amount via the tool directory with G41 and G42 for left or right hand compensation.
Very helpful and now subscribed because you have a great presentation style. 👍
Brilliant video, so informative and really funny 😄
For these things I pay my internet. Thank you so much
Amazing video! The editing on this was excellent, and I enjoyed all the visual puns and gags. I never got proficient enough in Paintbrush to find the 3D CAD features, but maybe that's unlocked by the paid professional license.
It's nice to see you back! I was checking your channel a few days ago to see if there were any signs of life that I missed notifications on.
There is life, but creatively there's not all that much going on. Best place to check in what's happening is instagram. I'm in between workshops right now, so I don't know when the next video will come. Hopefully not too long.
Super cool build.You make me want a laser cutter now...
Do it! Even a K40 is a good start if you don’t have much money to spend, but have a tinkering mind.
Nice thanks. I like th etip about long fingers, and sanding off the burned edges. Cheers
You totally can cut circuit boards on a laser cutter! Well, you apply a layer of something like spray paint as an etching resist, burn off the paint in the inverse of the pattern you want using the laser cutter, then etch away the exposed copper with ferric chloride.
Might make an interesting video actually
If only...I already made a video about etching brass plaques that can be used, pretty much verbatim, as a template when etching circuit boards 😉
@@SwitchAndLever Oh wow. Yeah, exactly that process!
Great video! Just what I was looking for.
Could you throw a little paste wax in the lid groove for smoother operation?
you can reduce or even eliminate soot and tar markings on wood by putting a layer of masking tape overtop of the wood. you can eliminate checks from where the laser cuts through the wood and encounters the blades or honeycomb table underneath by putting the wood on a sacrificial layer of non synthetic cloth. i use muslin since i have tons of it.
Don’t like the masking tape method myself, especially on a little rougher surfaces it tends to pull up grain and not seal properly leaving a gummy edge that still needs to be cleaned up anyway. If I’m going to sand the surface anyway (which I am) it’s really not a big deal to remove the soot at the same time.
You can also eliminate those bottom marks by elevating your piece a little using shims, but that does require a pretty flat piece to begin with. Since mine was warped I had to weigh it down to keep it flat.
Nice video, cool box and tool but more importantly, good to have you back on the tubes.
At least for now, I'm hoping I'll be able to make new videos more regularly soon again. 🙂
@@SwitchAndLever Can't wait to see more😊
Real cool video, I liked the butt joke. You explained the little things that a lot of people forget. I have now subscribed to your channel.
That's a nice box and a lovely box joint! I had no idea you could carve such deep and good grooves with a laser. Cool! Now pardon me while I go howl your name at the moon. Hope it's okay that it's summer, not winter here at the moment.
Unacceptable! At least throw some flour in the air to simulate snowfall! 😬
@@SwitchAndLever I don't want to waste the flour but I could definitely throw some sawdust!!
Typically you should add half the kerf width as both pieces will be increased by half to make the full width
Good to see you back and well!
Good to see a video from you again. Great as always.
Tip for glue up: add masking tape to the areas where there will be glue squeeze out, this will make cleanup a lot easier and faster. When the glue squeezes out and is starting to get gummy you can remove the tape and it should leave clean edges.
Yes, there's a reason I didn't do this. The plywood was crap quality, and masking tape pulled out wood fibers out of the surface when removed. I'm honestly not all that worried about glue squeezeout, especially if the joints will get more work done, or if they're in a place where it won't be seen or affect the end result.
Funny, when I lived in Stockholm years ago I made wooden cases for all the Abene and Bahco machinists tools I’d acquired. Still going strong 30 years on.
I for one appreciate the additional effort you put in to the motion graphics! *slow claps* This year wasn't the same without meeting up at MFBA :(
100%! I can't believe it's been over a year already! This year has been mostly kind of a blur. I was really looking forward to Maker's Central at least, but who knows when that will take place. Events like that are so important to all of us creators who only really see each other online otherwise.
@@SwitchAndLever A blur is a depressing yet accurate way to put it. Feels like it is being defragged/deleted as it progresses in a weird way. 😆🤷♂️
I loved all the small graphical puns
Good job! Thanks for sharing the knowledge!
The one and only... Great video as always, sir!
Loved your instructional and very informative video. Nice job!! I can't wait to try to make one of these!
Thanks for the helpful video man!
Happy to be of help! Does this mean a laser cutter is in your future? Jackman shoots lasers? Looking forward to it already!
@@SwitchAndLever just got one!! Only made a couple of test projects on it so far. Haven’t used it on a Jackman build yet!
@@JackmanWorks sweet! If you have any questions hit me up! Lasers are awesome, as long as you don't try to cut kevlar, never cut kevlar!
boxes are awesome!
Amazing video! Very useful tricks that can surely help a lot of people! ;)
Great video btw. That finished box was superb 👌
didn’t know you could accurately cut slots like that with the lasercutter, nice! you could have used that to cut a recessed thumb slot into the lid for easy opening : )
Yeah, I thought of it, but I wanted the top to look clean. It slides open easily enough anyway 🙂
Thanks for a great video! I'd love more videos on laser cutters!
If the curf is .2 why u adding .2 to both and not .1 ?
I had the same question. If your laser cuts exactly on the line then it should burn away the same amount on each side so the amount that needs to be adjusted should be half of the total kerf. I guess with material like wood it could be fine because it is somewhat flexible but acrylic on the other hand would possible struggle if you don’t get it exact and even 0.5mm could make a big difference. Especially, if you have many small finger then the excess material could easily amount to a few mm.
Yes it should be half of the kerf or close to that. Wood is quite flexible so you might want to make it tighter on purpose for a snug fit, but more rigid materials would benefit from being offset to something closet to the kerf/2
Very instructive. Thanks !
Great video!
I love how easy you made it all look.
I especially loved the retro styled graphics.
Thanks for sharing your time and effort :)
Awesome work Daniel! 😃👍🏻👊🏻
Cheers! 🙂
If I could offer some suggestions. Sand your whole blank before cutting. I like to use painters tape. Saves a lot of time cleaning up that nasty carbon. Or a little alcohol on a rag works great to remove the carbon, however, I've been experimenting with Clorox bleach and works better than alcohol but wear gloves because you won't get that smell off your fingers. Use rubber bands to help with the glue-up.
Don’t like sanding the whole board before cutting because that ultimately just leads to resanding stuff away anyway. The painters tape can help, but I find depending on the wood it can pull out grain from the surface, so I tend to avoid it. It doesn’t really take much time to clean up the soot anyway.
"...howl my name at the moon..." !! :-D Great video, thank you!
Bonne idée des sur épaisseurs !!! Merci !
Great video.
Can you tell me what type of varnish was used?
(Composition and brand.)
Cool video and great tips!
Awesome film. Nice animation, must have taken a long time using Paintbrush. : ) Great instructions, nice box. Mahalo for sharing! : )
Why do you think it's been such a long time since the last video? Those pixels ain't gonna animate themselves! 😅
Should the offset be 1/2 of the kerf? Greet video!
I just stumbled across this video. Very well done! I have seen people use transfer tape on both sides of the wood to eliminate the soot and need to sand the pieces. Before I purchase a roll and try what are your experiences?
Great video. I miss your vids.
Good practical advice!
Great video, Thank you.
I am just starting out with a laser cutter. I will definitely look for the online box template. When you draw in Paint, how do you get the drawing over to the cutter? I am using Lightburn.
i almost spit out my beer when i saw Windows 3.1, Paint do the box animation!
Really nice video!
Very much liking the animations. Very Return Of The Obra Dinn.
Well it's 1-bit graphics, commonplace in the 80s and early 90s, which is what Lucas Pope was inspired by when he made Return of the Obra Dinn. 🙂
@@SwitchAndLever were those graphics animated though…? I thought that was a new thing
@@RoamingAdhocrat oh, 1-bit animations have been around since that time too for sure. You had even quite action filled games, racing games like Grand Prix Circuit, which was fully 1-bit and full screen moving gameplay, back in the 80s. Or of course my favorite from the era: Shufflepuck Cafe.
I'm sure that I'm missing something, but why do you offset all the box joint surfaces by the width of the kerf? My (often unreliable) intuition suggests it should be half the kerf.
Hello, nice video! What is the program that you are using at @5:40 ?
My stepson and I have lasers. Very good video. Did you do the editing and FX too? How did you get that great accent? Where are good 3.4mm, 4mm wood sources in USA? Thanks.
You might check Michael's Craft Shops, they have an extensive array of different crafts
Had to change my shorts after that animation at the beginning 😂
Your video helped me a lot, thank you so much mate.
I'm planning to start my on small business in beekeeping and I would like very much to have your recommendation on which is the best laser cutting machine would be suitable for me to make Langstroth Beehive boxes made of 20mm thick Pinewood and Cedar Wood with finger joints shape.
Thanking you for your kind feedback in advance and best regards...
the bamboo wood I'm using has some flex to it (it doesn't lay flat), any tips on how to clamp them so they hold well? I'm creating a L-shaped divider for my partner's box
Fantastic. You rock!
Not even going to mention the massive twist in that plywood.
It was pretty massive, but that’s why it’s good to be cut down into small pieces, because it virtually disappears
It’s inconsequential. As long as you weigh the board down so it lays flat when cutting any little twist still remaining in the small pieces will easily be corrected when gluing the box together.
@@SwitchAndLever ...until you cut something that has a long side, which bends out of the flatly clamped-down stock as soon as you cut it, and your laser optics promptly crashes into it at high speed first time it tries to fly over it.
@@AttilaAsztalos so? Don't do that then, easy fix. 🤷♂
@@SwitchAndLeverYou just did so yourself, and tried to shrug it off as no big deal - except that's exactly the point: bent stock IS a big deal, even if you can clamp it down flat. You can't have it both ways. "It's inconsequential" until the first piece rises way up after being cut.
Another great and thought provoking video - thanks. I have neither the patience nor the laser cutter to make such strong joints and the "beauty of the joint" doesn't interest me so much, so the question for me is - how do you figure out the minimum number of interlocks to make so that the strength of the joint matches the strength of the material being used?
I am not a material's engineer, though I find using a finger size that matches the thickness of the material is a good starting point. The glue joint will be stronger than the surrounding wood for sure. If you're using other ways of cutting your joint, like with a table saw, you could even use the width of the saw blade as the width of your joint, as it will make things significantly easier. If you use huge fingers the joint won't be much stronger than a butt joint, just easier to assemble, if you use a massive amount of tiny fingers the joint becomes difficult to assemble and glue.
I have missed your videos! :) And howling at the moon makes no difference... Don't ask me how I know! :D
Great info!
Nice find on that vintage machinist's level.
Amazing. Thank you!!
shouldn't you offset by half the kurf? I mean the laser follows your dimensions and cuts both ways but I'd assume you'd only care for the part that cuts into your work piece.