The Playlist: ua-cam.com/play/PLoPtpxJIxgnYkYJeuY8U7AsOHmNRiesi2.html --Video Transmitters MMCX Great Antennas: bit.ly/2Sk5d6D Premium VTX: bit.ly/2Vvx4AH Budget VTX: bit.ly/2W2axMq Mid Range VTX: bit.ly/2ONep5a The Screen I used: bit.ly/2YYApuL
I'm trying to keep my hawk pro light,diamond vtx dvr I have laying around ,but cam connects directly vtx,omnibus cam connects to fc ,would I use vid out from vtx to fc ,no vid in?
Thanks for this. Your video tutorials are very helpful. But i have a problem i hope you could help me. I'm trying to connect my VTx (GEPRC Stable VTX v1.3) to my FC AIO (JHEMCU F411 Pro AIO). The VTx has 3wires has 8wires all-in, 3wires from the fpv camera (5v, grnd, video in one connector wire to the fpv camera), and another set of 5wires (5v, grnd, Vin, Vout, TXD). The last 3wires is what i have a hard time figuring out where they goes (Vi, Vout, TXD). The FC-AIO has 4pads open i can possibly solder the wires into. These are: Tx1, Rx1, VTx, and Camera signal. Can you please help me where i should solder the 3 VTx wires (Vin, Vout, TXD) into the FC-AIO pads (Tx1, Rx1, VTx, Camera signal)? Thank you again so much. And i hope you can help me.
I know this is an old video but that was amazing. Just getting into fpv myself and It can be very confusing at times. Videos like this are sooo helpful so thank you, it cleared up a lot!
If you are going to connect the VTX to the power input from the battery, you should solder a 1000 micro farad capacitor across the positive and negative terminals. This will serve to limit noise on the video stream. Also a good practice solder it on, to save sensitive electronics from voltage spikes.
Thank you ever so much for an easy to follow and most understandable tutorial!!! You have a gift for teaching this stuff and I sincerely hope you will continue to educate us new FPV pilots and builders of quadcopters. You have one more subscriber! 👍👍
Awesome video and great detail please do more of this videos they are very helpful to beginners. Do a tutorial video of how to wire different recivers like tbs nano and micro reciver . Thank you for providing the links to the items you use.
Please make a video about wiring an external microphone into smartaudio line incl. all the needed caps & resistors. I can't find this topic on YT. It would help many of us, cause the majority of VTXes do not come with an integrated mic on the board and it's kinda like being handicaped while flying, because you loose a very important piece of your senses... The community would surely be very thankful to you. Keep up that great work, you are one of the most important persons in FPV in the world! :)
I wish I had watched this and understood it back in 2019! Great video. I now already know most of this stuff (but learning the painful way), but I still picked up on a cool tip; and that's powering your flight controller with alligator clips before any solder ever hits the board! EXCELLENT! 👌
Dude, ty so much for this nice tutorial and for explaining it for absolute noobs like me, you literally answered me all my cuestions, absolutely nice video. 👏
Waiting for the part 2 of building FPV drone, the video ended with a heads up for part 2. Planning a build based on this bro. Thank you for all the support :)
The Drone Flew Amazing However the caddx tarsier was dead on arrival if you want to see how it flew check my runcam split 3 video it was that build that was flying but was flying very chill to capture the footage. So in i think 5 days I will receive the replacement. Also if you plan to build it do it because I will also release my pids for it.
If there's new guys watching these like I was. Definitely don't put a full batt vtx (7-25) on 5v. On another note I think 2023 (year) plus you may not need a S/A wire and can still access the betaflight settings. I have 2 builds that can, a 16x16 vtx that survived a fire and a hm850 from flywoo/RDQ.
We need a video on how to wire a vtx like that fx 2 ultimate. Directly to the tx housing / silver case. I wanna go around the plug. I think it has a short, or the harness.
I want ask a question about connection if a buy a camera and vtx module. The vtx module has 3wire so where should i connect the which wire in flight controler for drone or in receiver for rc plane
Great video man! You should go even deeper and let us know how to connect those wires in order to avoid things like failsafes or electrical noise, cause this is a very important and ugly part in fpv 😤🧐 thank you for your work and keep it up!
Great videos! Do you also have tbs crossfire setups? I have a multiple nano’s. I wired one of my quads in a similar way once, and I was able to control my vtx though my tbs module behind my taranis once and adjust my rates. by the way any videos on rate adjustments? I enjoy watching your videos also my baby niece loves your into song by the way 🤙 and thanks for recommending the dalrc f722 with 50 amp esc’s, flies gtreat on my marmotte, wish it had a barometer, was thinking of the matek f7, but really don’t need memory card adapter. keep up the great videos!
matek f411 wse connect fpv transmiter eachine nano vtx first atach -connect antena in transmiter..left to right side wires.. yellow soldering to vtx in matek,red soldering to vbt,black to G.I think so I have smog not working?????help please
Great video easy to follow. Unfortunately I still need some help.my smart audio is working but the table for power is wrong. I understand that if the mw value is wrong the vtx olny outputs 25 mw. Values of rdq. Vtx are 25,200,600 & 1000. Can I just enter a command in cli to change this, or do I have to flash 4.1 and import the tables. Then change table to correct values?
Thanks for this. Your video tutorials are very helpful. But i have a problem i hope you could help me. I'm trying to connect my VTx (GEPRC Stable VTX v1.3) to my FC AIO (JHEMCU F411 Pro AIO). The VTx has 3wires has 8wires all-in, 3wires from the fpv camera (5v, grnd, video in one connector wire to the fpv camera), and another set of 5wires (5v, grnd, Vin, Vout, TXD). The last 3wires is what i have a hard time figuring out where they goes (Vi, Vout, TXD). The FC-AIO has 4pads open i can possibly solder the wires into. These are: Tx1, Rx1, VTx, and Camera signal. Can you please help me where i should solder the 3 VTx wires (Vin, Vout, TXD) into the FC-AIO pads (Tx1, Rx1, VTx, Camera signal)? Thank you again so much. And i hope you can help me.
So I have a question, maybe is a dumb one, but I'm really noob at this. So I have a blue bugs 3 (it's a made drone kit for kids) and I always used just a budget camera with a 1s lipo, but as expected, the signal is very bad, so I was wondering if I could get one vtx and use it just with camera connected to the vtx and battery to power the vtx, without connect it to flight controller, because I don't have pads for that, or it's impossible to do that? Thanks so much for the help
Great tutorial I completely understand , but does connecting the vtx power directly to bat voltage degrade the image ? Sometimes I get a grainy looking image, no lines just grainy. Thank you
thanks for this video! sooo the current documentation for Eachine nano V2 VTX shows 5V IN, GND, "RX", 5V OUT, GND, and 5V OUT; I would assume the RX printed in this case should be a ""TX""? or does the RX in my case indicate receiving data from the FC's TX pad which is where I will solder to TX3?
IS it better to power the Cam from the VTX or the FC? I currently have a Rush Tiny Tank with the Cam power coming from the VTX but I'm getting interference.
So if I used a for instance,a diamond dvr 200mw vtx on a omnibus f4 fc ,mini mag stack,if cam goes directly to vtx on the diamond,would I keep cam in to fc as it's meant for,run vid out and not vid in on vtx?
after wiring all the connections and configuring it on beta flight, why did you not show how to load the lua script in beta flight? and where to download the lua script?
Is there any VTX power limit using SA 2.0 settings. I am using Eachine TX806 VTX that has 5 power levels 25,200,400,800 and 1000. It can be set to 1000mW using VTX control button but Smart Audio (by OSD or LUA Script) is able to set only to power level 4 (800mW). When I am trying to set to lvl 5 (1000mW) Smart Audio settings stops to respond until FC and VTX is power up again. Does anyone had similar issues?
Just out of curiosity, does the display ever pop up in the middle of a flight or is the command to boot it so out of the way its never popped up unintentionally?
Thanks for the video! What does it mean when inside VTX SA it says “statx” previously the menu was like shown in your video and I could change the settings. But after I crashed I’m having this issue. Sometimes I don’t even get an image. I’m struggling to find the problem :p
Man Its TOO bad your over seas from the US . Theres a market for Hey mr tech guy is this 4 in 1 ESC beyond help, or hey mr tech guy is this flight controller completely dead. Granted its nickle and dime and probablly stress, but there is assuredly a market for it. I've seen your videos on testing FETs . but I wouldn't do it myself .
The Playlist: ua-cam.com/play/PLoPtpxJIxgnYkYJeuY8U7AsOHmNRiesi2.html
--Video Transmitters
MMCX Great Antennas: bit.ly/2Sk5d6D
Premium VTX: bit.ly/2Vvx4AH
Budget VTX: bit.ly/2W2axMq
Mid Range VTX: bit.ly/2ONep5a
The Screen I used: bit.ly/2YYApuL
I really enjoy posts like this!!! One day i hope 2 build my quads and i will definitely watch this channel a lot lol!!!!!! Great post!!!
I'm trying to keep my hawk pro light,diamond vtx dvr I have laying around ,but cam connects directly vtx,omnibus cam connects to fc ,would I use vid out from vtx to fc ,no vid in?
Thanks for this. Your video tutorials are very helpful.
But i have a problem i hope you could help me.
I'm trying to connect my VTx (GEPRC Stable VTX v1.3) to my FC AIO (JHEMCU F411 Pro AIO). The VTx has 3wires has 8wires all-in, 3wires from the fpv camera (5v, grnd, video in one connector wire to the fpv camera), and another set of 5wires (5v, grnd, Vin, Vout, TXD). The last 3wires is what i have a hard time figuring out where they goes (Vi, Vout, TXD).
The FC-AIO has 4pads open i can possibly solder the wires into. These are: Tx1, Rx1, VTx, and Camera signal.
Can you please help me where i should solder the 3 VTx wires (Vin, Vout, TXD) into the FC-AIO pads (Tx1, Rx1, VTx, Camera signal)?
Thank you again so much. And i hope you can help me.
I know this is an old video but that was amazing. Just getting into fpv myself and It can be very confusing at times. Videos like this are sooo helpful so thank you, it cleared up a lot!
If you are going to connect the VTX to the power input from the battery, you should solder a 1000 micro farad capacitor across the positive and negative terminals. This will serve to limit noise on the video stream. Also a good practice solder it on, to save sensitive electronics from voltage spikes.
This helped out so much. Broke my vtx on my hornet and installing one for the first time. Thanks man.
By far the best fpv UA-camr 🙌
Another great tutorial, dude! Thanks a lot! 😃
"THANK YOU!!" for posting this! I just watched it for the third time and finally understand how to hook up the vxt! First time 5 inch build on my own.
Amazing video Best drone content on UA-cam
BEST CHANNEL EVER
Thank you ever so much for an easy to follow and most understandable tutorial!!! You have a gift for teaching this stuff and I sincerely hope you will continue to educate us new FPV pilots and builders of quadcopters. You have one more subscriber! 👍👍
Awesome video and great detail please do more of this videos they are very helpful to beginners. Do a tutorial video of how to wire different recivers like tbs nano and micro reciver . Thank you for providing the links to the items you use.
Please make a video about wiring an external microphone into smartaudio line incl. all the needed caps & resistors. I can't find this topic on YT. It would help many of us, cause the majority of VTXes do not come with an integrated mic on the board and it's kinda like being handicaped while flying, because you loose a very important piece of your senses... The community would surely be very thankful to you. Keep up that great work, you are one of the most important persons in FPV in the world! :)
I learned alot in you 2 videos aboute vtx's Thanks alote man !
I wish I had watched this and understood it back in 2019! Great video. I now already know most of this stuff (but learning the painful way), but I still picked up on a cool tip; and that's powering your flight controller with alligator clips before any solder ever hits the board! EXCELLENT! 👌
Hi thankyou for the best and informative vidio I have watched very clear and precise.
Thankyou so much it’s so informative for me. Greeting from Indonesia 🇮🇩
Thanks for posting, I haven't build a drone yet but want to and this helps a lot.
These videos are a great help. Keep up the good work!!
Finally learning to build from scratch. I needed this video. Good presentation and all that too thanks man
Super video , great information that I really needed. Thank you, Looking forward to part 3 . Peace !!
Dude, ty so much for this nice tutorial and for explaining it for absolute noobs like me, you literally answered me all my cuestions, absolutely nice video. 👏
Super helpful, very thorough. Lots of great information, thank you.
love your vids..do have a actual video on how to change your vtx with osd..i have not seen one proving that it actually works
Thank you for such an informative tutorial. This really helps us noobs
Waiting for the part 2 of building FPV drone, the video ended with a heads up for part 2. Planning a build based on this bro.
Thank you for all the support :)
The Drone Flew Amazing However the caddx tarsier was dead on arrival if you want to see how it flew check my runcam split 3 video it was that build that was flying but was flying very chill to capture the footage. So in i think 5 days I will receive the replacement. Also if you plan to build it do it because I will also release my pids for it.
If there's new guys watching these like I was. Definitely don't put a full batt vtx (7-25) on 5v. On another note I think 2023 (year) plus you may not need a S/A wire and can still access the betaflight settings. I have 2 builds that can, a 16x16 vtx that survived a fire and a hm850 from flywoo/RDQ.
Definitely helpful, DroneMesh === quality content
Nice, thats helpful to understand how to setup the VTX.
Great video sir. beautifully explained.
Great video man!! Very simple and on subject! 👌👍
We need a video on how to wire a vtx like that fx 2 ultimate. Directly to the tx housing / silver case. I wanna go around the plug. I think it has a short, or the harness.
Thank you so much for this video.
Thank you! Very helpful 👌
I want ask a question about connection if a buy a camera and vtx module. The vtx module has 3wire so where should i connect the which wire in flight controler for drone or in receiver for rc plane
Great video man! You should go even deeper and let us know how to connect those wires in order to avoid things like failsafes or electrical noise, cause this is a very important and ugly part in fpv 😤🧐 thank you for your work and keep it up!
Very useful. Thank you 👍👍
Great video! Very informative thank you!!!
Thank you this fixed my problem
Great video and info. Is there going to be a part 3 for Camera? Thx Really appreciated !!!
Great tutorial , thanks a lot for sharing :-)
Really wish you would have showed us more on the akk I am not sure if I power my batt with the 5v from my vtx or not
Great video it help me a lot
I appreciate the electrical build details. Thank you!
My Vtx channel set to R4 , but every time i turn the quad on, the my goggle said that on A4 . i've try to setup from BF but not result ,please help.
Thank very much for your info excellent! Thanks for you effort!
Great videos!
Do you also have tbs crossfire setups?
I have a multiple nano’s. I wired one of my quads in a similar way once, and I was able to control my vtx though my tbs module behind my taranis once and adjust my rates. by the way any videos on rate adjustments?
I enjoy watching your videos also my baby niece loves your into song by the way 🤙 and thanks for recommending the dalrc f722 with 50 amp esc’s, flies gtreat on my marmotte, wish it had a barometer, was thinking of the matek f7, but really don’t need memory card adapter.
keep up the great videos!
Men i wish you are ok i haven't see one of your videos in a long time I hope you and your family are ok.
Hi
My camera have 4 wire
GND DM DP 5V
Where should I connect the DM and DP cable on my VTX
As I know, we only need to connect 1 cable to Video on VTX
You are the best thnks man
Thanks a lot great tutorial
Great I have that same vtx and wao I found it need it thank u.
3 years later, which VTX might you choose for a long range wing... anybody? PandaRC, AKK any good?
Can I do this without a flight controller?
matek f411 wse connect fpv transmiter eachine nano vtx first atach -connect antena in transmiter..left to right side wires.. yellow soldering to vtx in matek,red soldering to vbt,black to G.I think so I have smog not working?????help please
Great video easy to follow. Unfortunately I still need some help.my smart audio is working but the table for power is wrong. I understand that if the mw value is wrong the vtx olny outputs 25 mw. Values of rdq. Vtx are 25,200,600 & 1000. Can I just enter a command in cli to change this, or do I have to flash 4.1 and import the tables. Then change table to correct values?
When i connect fpv tx to flight controller voltage goes to 10 volt and failsafe trigger why this happens
Thanks for this. Your video tutorials are very helpful.
But i have a problem i hope you could help me.
I'm trying to connect my VTx (GEPRC Stable VTX v1.3) to my FC AIO (JHEMCU F411 Pro AIO). The VTx has 3wires has 8wires all-in, 3wires from the fpv camera (5v, grnd, video in one connector wire to the fpv camera), and another set of 5wires (5v, grnd, Vin, Vout, TXD). The last 3wires is what i have a hard time figuring out where they goes (Vi, Vout, TXD).
The FC-AIO has 4pads open i can possibly solder the wires into. These are: Tx1, Rx1, VTx, and Camera signal.
Can you please help me where i should solder the 3 VTx wires (Vin, Vout, TXD) into the FC-AIO pads (Tx1, Rx1, VTx, Camera signal)?
Thank you again so much. And i hope you can help me.
Can you connect a microphone to the smartaudio pin on the VTX too?
Thanks
My problem is now i can‘t see a OSD not even when i set it up on bf!!! What can i do???
So I have a question, maybe is a dumb one, but I'm really noob at this. So I have a blue bugs 3 (it's a made drone kit for kids) and I always used just a budget camera with a 1s lipo, but as expected, the signal is very bad, so I was wondering if I could get one vtx and use it just with camera connected to the vtx and battery to power the vtx, without connect it to flight controller, because I don't have pads for that, or it's impossible to do that?
Thanks so much for the help
Great tutorial I completely understand , but does connecting the vtx power directly to bat voltage degrade the image ? Sometimes I get a grainy looking image, no lines just grainy. Thank you
How to record the fpv camera footage ??
thanks for this video! sooo the current documentation for Eachine nano V2 VTX shows 5V IN, GND, "RX", 5V OUT, GND, and 5V OUT; I would assume the RX printed in this case should be a ""TX""? or does the RX in my case indicate receiving data from the FC's TX pad which is where I will solder to TX3?
IS it better to power the Cam from the VTX or the FC? I currently have a Rush Tiny Tank with the Cam power coming from the VTX but I'm getting interference.
great video
Great video! where can i get the pins and extra wire(to lengthen) if I want to mount the VTX on a fix wing airplane?
So if I used a for instance,a diamond dvr 200mw vtx on a omnibus f4 fc ,mini mag stack,if cam goes directly to vtx on the diamond,would I keep cam in to fc as it's meant for,run vid out and not vid in on vtx?
I'm using a crazybee f4 v3 all the diagrams have video in and out why do you only use video out
after wiring all the connections and configuring it on beta flight, why did you not show how to load the lua script in beta flight? and where to download the lua script?
So how are you powering the VTX.
Can you show the actual cord with clips on it?
Where does vBat+ go? I have a Mamba 405 MK2. Thanks
Is there any VTX power limit using SA 2.0 settings. I am using Eachine TX806 VTX that has 5 power levels 25,200,400,800 and 1000. It can be set to 1000mW using VTX control button but Smart Audio (by OSD or LUA Script) is able to set only to power level 4 (800mW). When I am trying to set to lvl 5 (1000mW) Smart Audio settings stops to respond until FC and VTX is power up again.
Does anyone had similar issues?
best video
BTW you are a Super Teacher!
Thanks a lot!
This is great, my vtx is getting super hot. Any thoughts
They all get super hot
@@DroneMesh really I thought I wired it wrong
It is a Rush Tank VTx
Just out of curiosity, does the display ever pop up in the middle of a flight or is the command to boot it so out of the way its never popped up unintentionally?
Thanks for the video! What does it mean when inside VTX SA it says “statx” previously the menu was like shown in your video and I could change the settings. But after I crashed I’m having this issue. Sometimes I don’t even get an image. I’m struggling to find the problem :p
Download AskFPV everyone there will help you almost immediately
why do I have to change the power on every pack on most of my vtx's ?
and another one!
Can you make a video mod eachine vr006 for get sound from quad
Why Pit mode via switch not working with SA? I use mamba f405 stack + tx805. However from OSD I'm able to set pit mode.
Not all VTX have pitmode
good
using tramp on the vtx port is the only way to switch smart audio with osd...makes no sense
so many misspoken and sometimes wrong things. be careful and research your own information too
Going to fry something if you dont power it correct..oh well
Man Its TOO bad your over seas from the US . Theres a market for Hey mr tech guy is this 4 in 1 ESC beyond help, or hey mr tech guy is this flight controller completely dead. Granted its nickle and dime and probablly stress, but there is assuredly a market for it. I've seen your videos on testing FETs . but I wouldn't do it myself .
Last
6:20 UART port not USB port but now I'm just being a dick sorry