thanks for taking us along on the overhaul. I just bought a 4430 with a blown engine. I put a combine engine into the tractor and she runs good. the tractor operates nicely. might have to go through the brakes though. It growls a little bit louder than it maybe should while stopping. But mabey ill check screen for metal filings before I get to excited
You said on I believe the ten and 20 series tractor when you pushed the clutch in the loader,would not function until clutch was released. The neighbor has one what can be done to eliminate this issue?
@georgemarshall7508 when you hold the clutch down it stops the transmission pump. The Hydraulics will run long enough that if you come up to your wagon or Manure Spreader that you can function the loader. If you're going to be stationary for any length of time doing multiple hydraulic functions then just simply click the neutral and let the clutch out
I am putting replacement cab on my 4430 other one burned so had no hoses to go buy taking off need pictures to know were hose go have service manual but don’t understand wwhere they go all of them so i get them rite love fixing videos thanks would be a god send for me
Hi Jon, Question, is it posible to remove the top-shaft rear bearing-race without removing the oil pump. Can it be removed from inside the transmission case? Has anyone done this.
When we do a transmission overhaul I will roll the transmission into the center of the shop and steam clean it. Then hit it with air to get all the water off. And if we are going to be waiting for parts for a while I will take a penetrating oil aerosol can and spray it down so it doesn't rust on the gasket surface
I have a 3120, I have a problem with the disc brakes. It is a bucket adapted from a wheel loader. I would like your e-mail to send photos, I don't know if I have to remove the bucket structure to change the seals;
Great video. I am pretty sure the 4230 was the last NF Deere produced. Have you ever heard of or ran across any 30 series NF utility tractors 830, 1530 2030, 2630?
You mean heat for the shop? Grew up with wood. No way no how would I ever want to use wood for the shop. For the amount of time to go get wood and then a little bit of stove maintenance during The winter, I could build them hours out in the shop and make a lot of money.
thanks for taking us along on the overhaul. I just bought a 4430 with a blown engine. I put a combine engine into the tractor and she runs good. the tractor operates nicely. might have to go through the brakes though. It growls a little bit louder than it maybe should while stopping. But mabey ill check screen for metal filings before I get to excited
Good video Jon. That's going to be as good as new when your finished.
Thanks. Let's hope! Kind of crazy that a 50-year-old tractor with some rebuilding might make it another 50 years
always enjoy your old iron horse maintenance. I got a 4430 that the draft control is not responding trying to figure that one out.
I will be going through the three point hitch and adjustment procedures when this one goes back together if you follow that maybe it will help you
@@jonstevensmaplegrovefarms3754 thanks I will be watching
Great video thanks for sharing your knowledge
Thank you
Thank you,Great video
Thank you very much
You said on I believe the ten and 20 series tractor when you pushed the clutch in the loader,would not function until clutch was released.
The neighbor has one what can be done to eliminate this issue?
@georgemarshall7508 when you hold the clutch down it stops the transmission pump.
The Hydraulics will run long enough that if you come up to your wagon or Manure Spreader that you can function the loader.
If you're going to be stationary for any length of time doing multiple hydraulic functions then just simply click the neutral and let the clutch out
@@jonstevensmaplegrovefarms3754 thanks ill tell him
I am putting replacement cab on my 4430 other one burned so had no hoses to go buy taking off need pictures to know were hose go have service manual but don’t understand wwhere they go all of them so i get them rite love fixing videos thanks would be a god send for me
Do you have an email I can send them to?
Hi Jon, Question, is it posible to remove the top-shaft rear bearing-race without removing the oil pump. Can it be removed from inside the transmission case? Has anyone done this.
@@delhoose no you have to take off the 3-point and remove the pump
Thank you for the fast response and I love your videos. They’re very helpful thanks.
You should wash the tractor 🚜 steam cleaners
When we do a transmission overhaul I will roll the transmission into the center of the shop and steam clean it. Then hit it with air to get all the water off. And if we are going to be waiting for parts for a while I will take a penetrating oil aerosol can and spray it down so it doesn't rust on the gasket surface
Good start😂
Please tell me ur gonna paint it up. Ur completely redoing everything properly it wouldnt be complete without a coat of paint
Probably rattle can the hood..
Ha no I was going to try to do a nice job.
greetings, please help, I have a JD 4230, I can't find the location of the brake switch, the lamp can, picture greetings, Croatia
In America we don't have a brake switch on the tractors. What is not working?
I looked in parts and can't find one.
You can go to jdparts.com
@@jonstevensmaplegrovefarms3754 ok thanks i need to install a traction switch for the rear brake light
I have a 3120, I have a problem with the disc brakes. It is a bucket adapted from a wheel loader. I would like your e-mail to send photos, I don't know if I have to remove the bucket structure to change the seals;
4640jon@gmail.com
Thank you, I will take photos soon.
Great video. I am pretty sure the 4230 was the last NF Deere produced. Have you ever heard of or ran across any 30 series NF utility tractors 830, 1530 2030, 2630?
Never seen one of them with a narrow front I don't know how you even get it to work?
@@jonstevensmaplegrovefarms3754 I was just curious thanks for the response rock on.
I wish you were closer i would bring you some tractors to work on. I have 7 of them broke down. 8130, 8400, 8430, 5020, 3010, 2755, Super MTA.
Oh boy, the 5020 would be a fun one!
Гарна робота
Wood burner best heat constant heat
You mean heat for the shop?
Grew up with wood. No way no how would I ever want to use wood for the shop. For the amount of time to go get wood and then a little bit of stove maintenance during The winter, I could build them hours out in the shop and make a lot of money.
@@jonstevensmaplegrovefarms3754 around here they buy these outside stoves and heat house and shop.
En español por favor