Excellent video, very detailed. It's great that you have specified the tightening torques for the engine and transmission drain and fill screws. Thank you very much and greetings.
Nice machine! I commuted on something similar for years, there's usually space under the seat for storage and the front fairing usually does a decent job of keeping wind/rain off your legs and feet. Peace of mind with the service too👍
Thank you for your video, my horn has failed to operate, I just recently found where it is located on my Vision 110. But I don't know the order of the panels to gain access to it.
I bought the sump plug washer and gauze filter cover o-ring from a Honda motorcycle dealer. They had them in stock. I didn’t change the final drive bolt washers as I didn’t feel the need.
I overfilled my MkII Escort with engine oil in the '80s. Everywhere I went, I left a huge, white smoke screen. But, like the idiot that I was, I soldiered on.
The handbook didn’t state re. the level being check on the centre stand. I thought exactly the same and did consider getting it off the stand and allowing sone to drain out. Then I thought if more than 20ml came out I’d be worried so decided to leave it. Being a perfectionist can sometimes be curse!
2:55 For anyone looking to do an oil change using this Motul 10w 30 4T scooter oil, it's not MB but actually MA, on the back of the container it states MA, it's impossible for it to be both, so i contacted Opei Oils and their response was this. "Hello, Thanks for the message, this is an MA-rated Oil which is fine to use instead of an MB, the other way around would not be safe and would cause issues. MA can be used in place of an MB. MB cannot be used in place of an MA. MB provides up to a 3% Fuel Efficiency increase. Unfortunately, I am unsure as to why Motul have done this, as it is very confusing."
Hello good afternoon. Thank you for the information, please, what is the specified frequency for changing the transmission oil? The oil used for transmission is a correct 10w30? (special for 120ml transmission)
@@autoknight747 Ok thank you for the information. Does it matter if it's 10k or 50k km? But anyway I will change it immediately and follow it at least every 10k km.
Sipam u prenos 75w80 i dodam malo likvi moli ceratek i nemoze biti bolje radi savrseno i svi metalni zupcanici su perfektno zasticeni duzi vremenski period a Motul nebih sipao dzaba da mi daju u masinu samo Castrol power1 racing 10w50 u sve ga koristim od Hajabuse pa do ove male Honde i prezadovoljan sam,Motul je tesko smece po meni samo reklamu dobru ima,pozz,odlican video
It’s not that unusual. Using a torque wrench is better than stripping out threads on aluminium casings. Dealerships I worked for started providing gloves from the mid ‘90s and we all wore them. Before that it was barrier cream. If you work with vehicles all day you need to protect hands - mess them up and you can’t work. Used engine oils are carcinogenic, after all.
![2019 Honda Vision 110 | AutoReview | affordable & cheap to run [Episode 23]](/img/n.gif)
Excellent video, very detailed.
It's great that you have specified the tightening torques for the engine and transmission drain and fill screws.
Thank you very much and greetings.
Nice machine! I commuted on something similar for years, there's usually space under the seat for storage and the front fairing usually does a decent job of keeping wind/rain off your legs and feet. Peace of mind with the service too👍
Just what I needed. Thank you!
i use an all my Honda Scooters Motul Gear MB SAE 80 GearOil on the FinalDrive..... On the Engine i use the same Motul ScooterPower 10w30 as you do 🙂
Thank you for your video, my horn has failed to operate, I just recently found where it is located on my Vision 110. But I don't know the order of the panels to gain access to it.
Belle demo . Super 😊
Très beau tuto. Bien réalisé . Simple à comprendre
Thanks for this video this is useful
CAN YOU SHOW US HOW TO REMOVE THE FUEL FROM THE TANK IN A HONDA VISION THANKS
No es mejor para la transmisión final un 80w90 ?
Very good video mate, thank you!
Very helpful video sir ❤
Thank's for the video
What are the dimensions (inner/outer diameters and thichkness) of that aluminum washer for the engine oil plug?
This component is now fitted to the bike so I cannot measure it!
Very good Video 😀thanx
Hi. Could you advise me on the washers required as I won't know the diameters until I remove the old ones. Thanks.
I bought the sump plug washer and gauze filter cover o-ring from a Honda motorcycle dealer. They had them in stock. I didn’t change the final drive bolt washers as I didn’t feel the need.
I overfilled my MkII Escort with engine oil in the '80s. Everywhere I went, I left a huge, white smoke screen. But, like the idiot that I was, I soldiered on.
Did it take the extra final drive oil because the bike wasn't level? Or does the manual say to check the oil level whist on the centre stand?
The handbook didn’t state re. the level being check on the centre stand. I thought exactly the same and did consider getting it off the stand and allowing sone to drain out. Then I thought if more than 20ml came out I’d be worried so decided to leave it. Being a perfectionist can sometimes be curse!
Do u have a link to the rubber seals i cant find them anywheree
I buy my components from the Honda motorcycle main dealer where they have a parts department.
@@autoknight747 my oil is 10w -40 is that ok i have a honda vision 110 2014
Like your video very helpful ❤
You will find a syringe would be very helpful when refilling the gear oil and the oil is a lot cheaper buying bigger bottles.
Thanks for the vid - where did you purchase the o ring and washer from ? Many thanks
I got them from a large Honda motorcycle dealer that has a really decent parts department.
Can I use engine oil as gear oil.
Some people do but I prefer to use the correct gear gear oil.
-Que cantidad de valvulina lleva la caja de transmion ?
-Que densidad de valvulina lleva? Gracias espero que me respondas a las 2 preguntas😅
Helped with final gear oil reccomendation
Using the same engine oil for final gear is wrong
Para la transmisión final es mejor 80w90?@@stefanichev2684
2:55
For anyone looking to do an oil change using this Motul 10w 30 4T scooter oil, it's not MB but actually MA, on the back of the container it states MA, it's impossible for it to be both, so i contacted Opei Oils and their response was this.
"Hello,
Thanks for the message, this is an MA-rated Oil which is fine to use instead of an MB, the other way around would not be safe and would cause issues.
MA can be used in place of an MB.
MB cannot be used in place of an MA.
MB provides up to a 3% Fuel Efficiency increase.
Unfortunately, I am unsure as to why Motul have done this, as it is very confusing."
Like, Very good. What is câmera?
GoPro Hero 10
merciiiiiiii👍
Gear oil is also 10w30
Hello good afternoon. Thank you for the information, please, what is the specified frequency for changing the transmission oil? The oil used for transmission is a correct 10w30? (special for 120ml transmission)
The handbook for my bike indicates replacement every 2 years. My research suggested the correct oil is as detailed in the video.
@@autoknight747 Ok thank you for the information. Does it matter if it's 10k or 50k km? But anyway I will change it immediately and follow it at least every 10k km.
@@JeisonTerci It does not state a mileage interval, just every 2 years.
@@autoknight747 good to know, thank you very much! Have a nice day!
Hi mate, where do you recommend buying the engine oil, sump plug washer and o ring etc?
Cheers
@@richardkemp3421 I buy from a Honda motorcycle dealer. There’s a good one near Gatwick - P&H Motorcycles
Hi, thanks for the video. Does anyone know where is the oil filter located on version 2021, please?
Sipam u prenos 75w80 i dodam malo likvi moli ceratek i nemoze biti bolje radi savrseno i svi metalni zupcanici su perfektno zasticeni duzi vremenski period a Motul nebih sipao dzaba da mi daju u masinu samo Castrol power1 racing 10w50 u sve ga koristim od Hajabuse pa do ove male Honde i prezadovoljan sam,Motul je tesko smece po meni samo reklamu dobru ima,pozz,odlican video
haha, I've never seen anyone use a torque wrench doing up a sump plugs ( also the gloves, LOL ).
It’s not that unusual. Using a torque wrench is better than stripping out threads on aluminium casings. Dealerships I worked for started providing gloves from the mid ‘90s and we all wore them. Before that it was barrier cream. If you work with vehicles all day you need to protect hands - mess them up and you can’t work. Used engine oils are carcinogenic, after all.