How to Install Can-Am Maverick X3 Radius Rods
Вставка
- Опубліковано 25 чер 2019
- Shock Therapy Can-Am Maverick X3 Radius Rods:
- Available in both 1.250", 4130 chromoly or 7075 billet aluminum (1.25" diameter hex)
- Radius Rods are marked left hand and right hand thread for easy adjustment
- All kits come with stainless steel spacers and the highest quality, - - 3/4" teflon lined rod ends (F1 fit) for strength and longevity
Direct Link: shocktherapyst.com/can-am-x3-...
For a full list of Can-Am Maverick X3 products, please visit: shocktherapyst.com/can-am/
Thank you for watching our video! Shock Therapy is a world-class suspension tuning and component company based in Phoenix, Arizona. We make original products right here in the USA and ship worldwide to all customers. Whether you are a casual owner or a racing enthusiast, Shock Therapy makes sure to place you FIRST. Purchase our Limit Straps, Dual-Rate Spring Kits, Sway Bars, Tie Rods, Ride-Improvement Systems and more at www.shocktherapyusa.com
For more information on Shock Therapy, keep up with us on our other Social Media:
FACEBOOK | / shocktherapyllc
INSTAGRAM / / shocktherapyusa - Авто та транспорт
I really appreciate the very detailed install video… I bought radius rods from another company that has no written install, and no video install instructions, but about 1000 videos of them dude-bro’ing it up. It would be great if everyone supported their product like you do. I will be back for your products and support in the future.
Thank you for the great feed back. We really try to make it easy. Thx again🤘🏻
Pro Tip: You should post links in the description for the products shown!
No one hardly does this anymore unfortunately :(
Thanks for all the detailed measurements
X3 looks so good on those 35's!
Love your videos!
are the measurements given in this video for a 72" wide machine
Sounds like i need to find an alignment shop fast. I couldn't figure out why my x3 was turning to the right so i adjusted my front to allow me to drive straight. My old rods were mangled up to take any measurements an i purchased used squeeky ca tech rods
How much is the pull plate for the x3 ? Thanks
What is the length of the lower radius rod? want to double check my rods. Thanks in advance. X3 XRS
So what do you recommend for my front end it’s been set by an alignment shop at zero should I toe it in or out ? It’s a little squirrely as is .
little bit or out because it’s a little Squirrley in the front end
We have found that 1/4 inch toe in front and rear is the most stable.
Are the chromoly rods as strong or stronger than the bullet ones?
4130 is stronger than billet aluminum radius rods by roughly 20%. But the billet rad rods are way over built and don’t fail unless you directly hit boulders with them.
Do the tire shops know to never adjust the lower link on the car when you take it to them for final alignment???
If they watch our video instructions then yes👍
Does it make a difference if I tighten up the rear plate bolts when the car is sitting on the ground?
Nope. You can tighten that any time. Just don’t have it too loose when you put it on the ground. The cars weight will try to move the rods around.
How is that a double shear plate?
I was wondering the same. Seems like a double bolted to a single. Still in the big picture a single?
It’s a double shear plate with the other bolts tightened. If there were only one bolt, yes, I’d agree.
Do you think the sep dog bones are needed with ur radius rods and Geiser hitch plate?
No. We do them all the time with or without.
@@ShockTherapyllc do you recommend them or they are not really needed for play car
@@miafunkno really needed.
I am a Samurai
Oh Hell ya you are. After a couple drinks, I am confident that a kick in the balls would not have stopped you in the slightest! LOL
Bonsaiiiii 😂
I Really Wish That X3 Wasn’t CVT.......Its The Best Looking SxS On The Market. Its The Closest To What A Sandrail Looks Like...
That CVT Is A Bummer...
lul
There's nothing wrong with CVTs. They've been around for a long time and they have made them work very good and work great. All you have to do keep them clean and maintained and you'll never have an issue. At least on a CanAm
You guys should spell shear correctly. It would give me confidence that someone there has an engineering background. Otherwise, looks like a great product. I just bent one of my OEM radius rods and these are at the top of my list. 👍