After watching your video. I looked at the key with the flashlight and there was no hole. I cleaned the jet until I could see light. 😂. It worked perfectly. Thank you
Have now used this to clean house siding and it performed well ua-cam.com/users/postUgkx43QMbQqu67IZadu9ou8Sg1BdrunMRNqX I also bought some wand extensions which enabled higher washing without needing a ladder. I recommend both. This unit arrived quickly, was easy to assemble (only had to attach the handle), and arrived in perfect condition. The only very slight downgrade from a perfect score is the design has a low handle and requires pulling from the side. My old washer was an upright model, while this one is more horizontal. Other than that, it's perfect for my needs. It has a great deal of pressure and more easily cleaned the house siding, porch rails and concrete than did my older model. The engine is a bit louder, as well, but the total time to clean was reduced by the more powerful spray. Did I mention it starts on the first or second pull every time?!! I am definitely happy with this model.
I have the same exact pressure washer got it out of the shop yesterday new carb, new on off switch ,new rubber feet , various gaskets etc. Runs great going to use ethanol free true fuel moving forward. It about 10 years old bought at Costco. Great job great video!!! Thank you
Part number for the Honda engine shown in video is GCV190LA N5AP.. It's on a sticker on the back side of the engine.. The side facing you when you're standing behind the handle.. There's also a QR code on the sticker but it was too faded for my phone to recognize..
Great video! I bought this model (new) several years ago. I use ethanol free fuel in all my law equipment & run out the fuel each fall. After oil change, partial fill of tank with fuel, I started my GC190 & ran it for 15 min, and it shut off & won't start back up. I cleaned sparkplug, put a little more fuel in tank, cleaned the vent holes in the fuel cap. It fires up with choke on, but won't remain running. Any ideas would be appreciated.
I would start with the carburetor.. Removal and cleaning.. This kinda backs that up based on your issue:www.ereplacementparts.com/repair-center/lawn-equipment/lawn-mower/only-runs-with-the-choke-on/#:~:text=An%20engine%20that%20will%20fire,flowing%20through%20the%20other%20passages.
I believe anywhere between .006 to .010" is acceptable but I've never used a feeler gauge.. The recipe card I used in the video was an insert in a magazine and seems to work well..
This looks like my exact model, but I haven’t died, I’m just disabled and all my tools have been sitting for years now, however I’m hopi g to get the. All up and running again, it will be a giant victory for me if I can pull this off thanks for the videos, oh and I cleaned the carb and I’m having difficulty putting everything back in the core t locations. Currently I’m struggling with reinstalling the linkage. HELP! Please.
I bought a brand new one with the gcv 170 engine, but it won't starts. Spark plug and carburetor looks good. When cord is pulled, I can see some smoke coming out of the metal vent hole. I don't know what else to do. Any idea? Please help
Yeah I saw that method used in someone's video recently but didn't know about it when I worked on this pressure washer.. Good to know it works I'm sure I'll use it someday..
After watching your video. I looked at the key with the flashlight and there was no hole. I cleaned the jet until I could see light. 😂. It worked perfectly. Thank you
Glad to have helped..
Perfect! After watching this video and following these steps my Honda power washer cranked on and did the job! Thank you--
Glad to have helped.. Thanks for reply..
Thx, im working on mine now. The bowl gasket broke when taking it apart and new one arrived today via Amazon:)
You're welcome.. Glad to have helped..
Have now used this to clean house siding and it performed well ua-cam.com/users/postUgkx43QMbQqu67IZadu9ou8Sg1BdrunMRNqX I also bought some wand extensions which enabled higher washing without needing a ladder. I recommend both. This unit arrived quickly, was easy to assemble (only had to attach the handle), and arrived in perfect condition. The only very slight downgrade from a perfect score is the design has a low handle and requires pulling from the side. My old washer was an upright model, while this one is more horizontal. Other than that, it's perfect for my needs. It has a great deal of pressure and more easily cleaned the house siding, porch rails and concrete than did my older model. The engine is a bit louder, as well, but the total time to clean was reduced by the more powerful spray. Did I mention it starts on the first or second pull every time?!! I am definitely happy with this model.
Excellent video! I founded same pressure washer model , I did the deep cleaning and I have a nice pressure washer for free ! Thanks for this video
You're welcome.. Glad the video helped..
I have the same exact pressure washer got it out of the shop yesterday new carb, new on off switch ,new rubber feet , various gaskets etc. Runs great going to use ethanol free true fuel moving forward. It about 10 years old bought at Costco. Great job great video!!! Thank you
Best video I've seen yet
That’s very helpful. I was given one just like it last week.
This is awesome pulled my pressure washer yesterday to clean the driveway and it was dead. Now I know what to do.
Good Luck.. Hope you get it running..
the flashlight trick was clever. never thought about that
You da man! Awesome how you got this started . Thanks for sharing.
You can buy these carburetors new, for $27.00 dollars. I just replace them and maybe try to rehab the old one if I have the time.
yeah if cleaning hadn't work i probably would have gone that route..
Where did you find the model/part number?
Part number for the Honda engine shown in video is GCV190LA N5AP.. It's on a sticker on the back side of the engine.. The side facing you when you're standing behind the handle.. There's also a QR code on the sticker but it was too faded for my phone to recognize..
Excellent video young man. Keep up the good work!
Thank You.. Will Do..
Great video!
I bought this model (new) several years ago. I use ethanol free fuel in all my law equipment & run out the fuel each fall. After oil change, partial fill of tank with fuel, I started my GC190 & ran it for 15 min, and it shut off & won't start back up. I cleaned sparkplug, put a little more fuel in tank, cleaned the vent holes in the fuel cap. It fires up with choke on, but won't remain running. Any ideas would be appreciated.
I would start with the carburetor.. Removal and cleaning.. This kinda backs that up based on your issue:www.ereplacementparts.com/repair-center/lawn-equipment/lawn-mower/only-runs-with-the-choke-on/#:~:text=An%20engine%20that%20will%20fire,flowing%20through%20the%20other%20passages.
great Job Bob
Hi, do these engines have a compression release? when I turn mine over it pushes air out of the crankcase....
Great tutorial thank you! Gonna work on mine tomorrow!
You're welcome.. Good Luck!!
@@tongo117 I took mine apart and cleaned it up yesterday after watching your video. It runs like a champ again! Thanks!
Glad to have helped..
GREAT VIDEO!!! What is the actual gap between the magnet and rotor?
Thanks! You made this all understandable...
I believe anywhere between .006 to .010" is acceptable but I've never used a feeler gauge.. The recipe card I used in the video was an insert in a magazine and seems to work well..
@@tongo117 THANK YOU..
My emotion tube is running out of patience
This looks like my exact model, but I haven’t died, I’m just disabled and all my tools have been sitting for years now, however I’m hopi g to get the. All up and running again, it will be a giant victory for me if I can pull this off thanks for the videos, oh and I cleaned the carb and I’m having difficulty putting everything back in the core t locations. Currently I’m struggling with reinstalling the linkage. HELP! Please.
I bought a brand new one with the gcv 170 engine, but it won't starts. Spark plug and carburetor looks good. When cord is pulled, I can see some smoke coming out of the metal vent hole. I don't know what else to do. Any idea? Please help
If it's brand new and won't start I would return it for a refund or replacement..
Damn these things need so much maintenance
i used a small allen wrench to push it futher and it came out!
Yeah I saw that method used in someone's video recently but didn't know about it when I worked on this pressure washer.. Good to know it works I'm sure I'll use it someday..
Did everything you did but still won’t start
Have you checked the plug/coil for spark?
Just replace the carb. They are like $19. You would have been done in 10 minutes instead of two days.
so spend $19 because the main jet was clogged.. and your 10 minutes starts after waiting a week for delivery.. no thanks..