Thanks man I actually have a table from the same manufacturer as your patio furniture cuz I actually have those chaise lounges one of the legs on my table broke off during a move where it attaches with a bolt I'm going to try the J-B Weld and figure out how I can add a bolts for strength
You have nice taste. If you can fit a bolt in it then that does work really well... if not you could use a piece of metal as a splint in the back of the leg where it is not noticeable and epoxy it all together. Doing a splint type repair was actually my first thought until I realized I could fit a bolt into it. Although the JB weld holds pretty good, you definitely want to reinforce it if you can.
Does this work for a hollow metal “pole” that snapped in half? It’s the metal pole that runs through the middle of my artificial Christmas tree ughhh… It is on the top part of tree & the snap is only 3 rows from very top so the amount/size of branches above the snap is very minimal.
If the pole is already hollow, then you already have a place to JB Weld a bolt or piece of metal rod into place to act as a reinforcement of sorts. Worth a try.
I dunno which JB Weld company you used but mine did not bond at all. I got the Epoxy steel resin with the hardner. I was trying to bond a steel plated nut to a steel shaft on a electric motor. It never bonded and I was able to remove it with my hand after 24 hrs curing. I sanded the steel and put some acetone to make everything was clean. I did this 3 times with JB Weld. I tried 3 brands of metal glue but all the same problem. I tried super and gorilla steel epoxy and same problem. I solved the problem by getting it welded. I also was emailing JB Weld support and they check the glue and also the pictures and video I sent to them. They could not understand why it would not bond. Reply
I don't know. If you mixed it in equal parts and it wasn't real cold where the reaction was slowed down... it should have cured hard and stuck well. Weird that JB Weld couldn't come up with an explanation since they should know better than anyone. Even weirder that you had the same issue with 3 different brands.
Clean the area from any dirt dust or corrosion... then prime and then paint with a similar color. It probably wont be quite as good as the rest of the factory powder coating, but should be much less noticeable then a big white splotch..
I don't think thinning it would work too well and it's probably not the right solution for your application. Perhaps something like this might be better... www.amazon.com/tire-bead-sealant/s?k=tire+bead+sealant
Depending on your application. Jb weld can be brushed out with water or a wet finger while it is tacky. Give it a couple minutes before rubbing out. I’ve used water to smooth out plastic trim repairs on the car and as a paintable coating on outdoor wood projects. Also to coat rebar ends in old concrete as pre primer before painting.
From a functionality perspective that would probably work, but putting the bolt inside looks close to seamless unless you really look for it up close. If I was motivated enough to touch it up with paint then you'd never know it was ever broken.
I broke my femur in a biking accident......cleaned it with whiskey, fixed it with JB Weld. 12 years later I'm still walking!
THIS IS FABULOUS. I ONLY WISH I COULD GET SOMEONE TO THE REPAIR ON MANY OF MY LOUNGE CHAIRS.
Thanks man I actually have a table from the same manufacturer as your patio furniture cuz I actually have those chaise lounges one of the legs on my table broke off during a move where it attaches with a bolt I'm going to try the J-B Weld and figure out how I can add a bolts for strength
You have nice taste. If you can fit a bolt in it then that does work really well... if not you could use a piece of metal as a splint in the back of the leg where it is not noticeable and epoxy it all together. Doing a splint type repair was actually my first thought until I realized I could fit a bolt into it. Although the JB weld holds pretty good, you definitely want to reinforce it if you can.
You definitely don’t want to traumatize your bolt😎
Great tips!
Does this work for a hollow metal “pole” that snapped in half? It’s the metal pole that runs through the middle of my artificial Christmas tree ughhh… It is on the top part of tree & the snap is only 3 rows from very top so the amount/size of branches above the snap is very minimal.
If the pole is already hollow, then you already have a place to JB Weld a bolt or piece of metal rod into place to act as a reinforcement of sorts. Worth a try.
@ thank you!!
I dunno which JB Weld company you used but mine did not bond at all. I got the Epoxy steel resin with the hardner. I was trying to bond a steel plated nut to a steel shaft on a electric motor. It never bonded and I was able to remove it with my hand after 24 hrs curing. I sanded the steel and put some acetone to make everything was clean. I did this 3 times with JB Weld. I tried 3 brands of metal glue but all the same problem. I tried super and gorilla steel epoxy and same problem. I solved the problem by getting it welded. I also was emailing JB Weld support and they check the glue and also the pictures and video I sent to them. They could not understand why it would not bond.
Reply
I don't know. If you mixed it in equal parts and it wasn't real cold where the reaction was slowed down... it should have cured hard and stuck well. Weird that JB Weld couldn't come up with an explanation since they should know better than anyone. Even weirder that you had the same issue with 3 different brands.
useful video!
Thanks
Is there anything we can use to Re-coat a small area that has chipped off leaving an almost white splotch on the otherwise dark cast aluminum table?
Clean the area from any dirt dust or corrosion... then prime and then paint with a similar color. It probably wont be quite as good as the rest of the factory powder coating, but should be much less noticeable then a big white splotch..
@@DIYWithAaron so just some type of metal paint like Rust-oleum you think?
I'd search on google to see what other people suggest. I've not painted cast aluminum myself but I know you can.
Is there a way to thin it so it's brushable? Want to repair a pitted wheel bead.
I don't think thinning it would work too well and it's probably not the right solution for your application. Perhaps something like this might be better... www.amazon.com/tire-bead-sealant/s?k=tire+bead+sealant
Depending on your application. Jb weld can be brushed out with water or a wet finger while it is tacky. Give it a couple minutes before rubbing out. I’ve used water to smooth out plastic trim repairs on the car and as a paintable coating on outdoor wood projects. Also to coat rebar ends in old concrete as pre primer before painting.
Is it still holding up now?
Yep, good as new still.
@@DIYWithAaron
Great, thanks for the reply
My headset broke so i fixed it with the weld
Instead of drilling a bolt how about a pipe ring around the 2 broke pieces ?
From a functionality perspective that would probably work, but putting the bolt inside looks close to seamless unless you really look for it up close. If I was motivated enough to touch it up with paint then you'd never know it was ever broken.
Ps thanks 😊 for the tips
Yes, everything is fixable!
I’m about to use it to fix my gazebo after a hurricane broke it
Every time I use j b weld 8 times out of ten it doesn’t hold not a big fan of this product