Це відео не доступне.
Перепрошуємо.
1996-2000 Civic Ebay 24mm swaybar install
Вставка
- Опубліковано 7 лют 2020
- How to install a cheap Ebay Chinese rear subframe tie brace bar, with the infamous JDM logo on it, and a cheap generic 24mm Chinese sway bar. This should be the same for all 1992-1995 Del Sol, Civic, and 1993-2001 Acura Integra too.
• Ej8 Honda Civic sleepe...
Here is the link to the playlist from building this car
D16y8 EK EJ6 EJ7 EX DX HX LX CX GX VP Si 1996-2000 1997 1998 1999 96 97 98 99 00 VTEC
Disclaimer:
Due to factors beyond the control of Rust Belt Auto, it cannot guarantee against unauthorized modifications of this information, or improper use of this information. Rust Belt Auto assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this video at your own risk. Rust Belt Auto recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of Rust Belt Auto, No information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained.
This helped a bunch man thank you
😁
i just purchased the same bar its a pain in the AXX to install....
I’ll second that
Quick question, do you have a link to the rear Si sway bar end links and the small silver sub frame brace brackets? Looking at getting those for my Ebay Swaybar and Truhart Subframe brace.
www.ebay.com/itm/162015187627?mkcid=16&mkevt=1&mkrid=711-127632-2357-0&ssspo=yucMq8wiS-G&sssrc=4429486&ssuid=QXZTigxVTHS&var=&widget_ver=artemis&media=COPY
www.ebay.com/itm/404571026186?mkcid=16&mkevt=1&mkrid=711-127632-2357-0&ssspo=eap8gya0rug&sssrc=4429486&ssuid=QXZTigxVTHS&var=&widget_ver=artemis&media=COPY
You mean this stuff?
Lol I’m dead I just this video and I Decided to do the same thing because I still have my head studs and they fit which is fucking killing me😂😂😂
Great video but, the spherical end links are better than stock links, also, you're supposed to pre load your suspension while installing a sway bar
Wrong. Pre loading does not matter on a sway bar. Also, heim joints are not better. If they were, manufacturers would use them. None do.
Do you recommend this or just get the brand name ones for a bit more $$
@@ReginaldSharma it works.
@@RustBeltAutobut need the bolts... Which I don't have lol
Yo!
Yo!
Yo!
I’m curious how everything feels on the street for you. Watched your video installing the ground control Koni’s. Is the ride quality about what you expected? Stiffer? Softer?
From my research, and what I gathered from that video, I think our goals might be about the same.
The coils made it stiffer. The shocks made the rebound slower. That was the big noticeable difference. Basically less bouncy, and stays planted on the road way better. Swaybars decrease body roll. stiffer in the rear promotes over steer, and stiffer in the front promotes under steer. Too much swaybar makes the car handle like it no longer has independent suspension. It's all in how you want the car to behave.
Have not driven it with the rear swaybar yet. But the suspension is firm enough for a nice ride on the tires that are on there, and it is definitely the best handling car I have owned. I could do stiffer rear coils too, but not going to go there. Also have 205/50/15's, But I like my HX rims for the street. The way this suspension is right now, is pretty close to the way a type R is set up. Sorry for the long post.
Rust Belt Auto no worries on the long post, you gave me exactly the info I was looking for. Thank you for taking the time to respond in that way.
Intuitively, I was between 15’s and 14’s for the reasons you mentioned. And was also curious if the eibach pro kit springs would be better spring rates to run (maybe it would be with 15’s). I also decided on the same swaybar setup as well, funnily enough, so I’ll keep and out for any updates on that.
Thanks again 👍
@@VeggieLard the nice thing about ground control's, and koni's is the variety of springs you can order, and the adjustability. People seem to like pro's just fine.
Where did you by the bolts that went through the rear subframe braise and the end links thank you for this video , I have aftermarket rear lowers .
did the d16 head bolts held good? or it didnt work out?
Regular ARP studs are probably fine. I put oversized studs in mine, because the head kept lifting. Both the tuners had too much timing in the thing. It blew a head gasket again after going oversized, then I dropped the timing back a bunch, and have no problems.
@@RustBeltAuto oh , i think i didnt ask right , did the head bolts you used for the suspension held ? Cause i thought on using some head bolts myself for the control arm cause my ebay kit does not even have those long bolts... Sorry for my bad english and thanks for answering!
Now that you've had some time to drive it, how is the difference between this bar and the del sol bar?
Any complaints about this bar? Seems to be the knockoff of a asr bar
It corners on 3 wheels! I'm only afraid the frame is not strong enough to support it.
I Just bought the same sway bar and just unboxed it for my civic, I bought it for a dirt amount of cheap 😂
Hope you got head bolts.
@@RustBeltAuto Turns out the one I ordered was defective, the washers welding to the bar are at a completely wrong angle, Ugg I’ll have to modify it myself but other then that it fits OK. Give it up for the eBay junk😂
@@alexraccuia7550 I had the same issue. I cut this washers out because it would'nt work. I am thinking now to use some D brackets. I dont know which one yet. But I am thinking about some universal ones or use the type r ek9 brackets. I dont know if ek9 will support 24mm. If you will figure something out give some info :D
@@MotoHooked Ok definitely yeah let me know how I goes, I’m going to cut the washer off and put it on the inside of the bracket, just to keep the washer there but it won’t interfere with the bend
@@alexraccuia7550 Yes this is good idea. I will do probably the same or use lateral locks
Watch out for that China bubble wrap air
Lol I know you mean to get onto his ear noise protection with that comment😂
It this fit the type r??????
Ek civic? Yes.
@@RustBeltAuto Acura Integra 2001
@@dembaba6513 Your stock one might have different end links. Think the bar for that is the same as Del sol, and 1991-95 civic. You should be able to make it work.
Link to sway bar?
I used 2000 civic Si sway bar links.
@@RustBeltAuto lol I meant to say the website or link to your new sway bar
@@chaleeher1992 it was the cheapest 24mm Chinese sway bar on eBay. I think this is it. Mine was cheaper, and the seller sold out.
www.ebay.com/itm/264410106470
www.ebay.com/itm/233418702090
And this.
@@RustBeltAuto okay thank you