This is a wonderful hack, my son said he wanted to go faster on his bike so he decided to do this, the results are great, the hack works, this great video helped a lot.
@@obl1xif_y981 I did this to my bike i got in July of 2021 and it increases the max speed to around 16.5-17 MPH (throttle only). I commented before i did the hack.
Hi Tony. Fantastic mod. I've added just about every mod out there to my Jetson, including being able to carry and easily change out three batteries for long rides. However, until now I've held off on hacking the speed control because I wanted a simple, cost affective solution that didn't add more clutter. So your solution checks all the boxes for me. It's the best electric out there for fun on the trails. Thanks again for sharing your engineering skills with all us Jetson Bolt Pro fans. I'm a new subscriber for you and I will keep watching for more of your ideas.
Hello D Hoffman, I’m glad that this solution works out for your Jetson Bolt Pro. It really is an amazing electric vehicle! Thank you for the subscribe, it really means a lot to me!
I used this process last week to update my daughters Jetson Bolt Pro in addition to adding a parallel battery, 60T chainring, and folding pedals. What a difference. Now that little bolt can keep up with our full sized ebikes. It goes around 16-18mph with my 10 year old with a little pedaling and we went 19 miles and it only used 1 bar. The second battery is 10.6ah giving it around 17ah at 36V nominal. We passed some stock Jetsons on the bike path and it was quite a difference in speed.
For anyone considering doing this speed mod, here's my experience. You will probably need a bigger chainring to increase the gearing to compensate for the added power. Even at lower speeds, I found my gears were constantly spinning and not giving me enough resistance from pedal assist. For those only wishing to use throttle power, this would be fine. But I wanted to keep my pedal assist to give me some more exercise and to give me more range.
If you care about exercise, maybe consider disabling pedal assist. I know there are many great tutorials on how to do it and it will give you more speed when you pedal!
@@angelor6899 Hi & thank you for your question. Yes it should work fine as both bikes are basically the same (Made in the same factory by the same company). The DYU is made by a company called "F-wheel" who also sell the bike to other companies who then put their own badge on it, i.e. "Jetson". Not sure if you know but there is also a reddit page for the bikes where there is loads of info worth reading.
why would you get an ebike for exercise? just ride a regular bike? The pedal assist is just working better with the added power, its literally just assisting you more. Your gears spin whenever you pedal, thats how gears work, so I'm not even sure what your trying to say?
used this mod and it worked! I am able to go around 18 mph, I'm seeing in the comments that some of the newer models of the bike do not work with this mod so if you have bought the bike recently I wouldn't recommend trying this out.
I think you are correct. I just bought mine last weekend and did the mod but no change in speed between my pre and post test. I already had the Arduino board so it was only 20 min of my time to try.
Done, Thanks ! 32km with back wheel in air, Kugoo V1. If hack didn't work u need to replace/rewrote False to True in agree arrangement which is in the sketch right under to 19th mile line
I was able to use this hack, i adjusted the speed to 20 and tested and 22 and tested, on a straightway there was no difference but it does add about 3-4 mph for sure!
Thanks. It works. I've set it to 23mph. When the bike reaches 22-23 it starts reducing speed, which can be felt especially on a downhill. But I also did shunt mode and installed 48v 10Ah battery. I also have two fans inside the case to prevent overheating.
I wrote the program for the speed hack. For those wondering "Why am I not getting 19 mph when I set it to 19 mph" : This hack programs the controller to attempt 19 mph, but without upgrades to the battery (adding another battery in parallel to be able to push more amps) it may not be achievable and instead you will only see a slight improvement. Just the same as when the battery state of charge is low you will notice it has less power and speed.. or when you throttle and you see the bars on the display drop from 3 bars to 1 bar - the battery is the weakness to achieving the desired speed. Thank you for making a video tutorial about the program to get it out to more people that wish to do it and playing customer service- I was getting a lot of comments asking how to do it which has stopped now thanks to you! Also, I just updated the program today to be more constant at verifying the hack has been complete - watch for 2 blinks of the headlights.
Thank you, i bought the board you showed, made up some wires to connect it and upped the speed to 20 mph all through watching your video. Im so pleased. P.s. i do have a faulty throttle but that was like it before anyway.
I just scored five of these Bolt Pros at Costco yesterday for the family and I. What a blast... Even more now that I ran across your video and was able to successfully reprogram a few of them (getting late here now) tonight for quite an improvement. I'll have to GPS each of us and see how quick they really are. Thanks for this video!
I just purchased one from Costco and I wasn’t able to do the speed hack, I did all the steps and got the two blinks from the headlight but still is only limited to about 14 on flat ground. Any ideas?
@@dylansessions9027 mine too and got mine last year from Costco (5/2021) build date. I don’t know how these recently purchased Jetson bikes are taking the hack unless they are NOS…
After watching this I ordered the bike and Arduino. My e-scooter has similar specs and price but it's hard on the knees after 30+ minutes and I'd like to burn some more calories. Cheers!
I borrowed a Jetson Bluetooth module to do mine last fall, but I just picked up a 2nd Bolt Pro for my wife, and I will be doing this to mod her speed. Thankyou so much for the video !
Great tutorial that was to the point, worked exactly how you mentioned even though I used an off brand Elegoo Mega2560 that I've had laying around unused for years - everything lined up 1-to-1 perfectly from your instructions and the Arduino site and agent work with it too. Thanks! Got two headlight flashes the very first try because of you.
Thank-you for your videos on JETSON Bolt . Because of the upgrades you have encouraged us to buy a JETSON! I can hardly wait to ride the e-bike! -Angèle
Really good mod. On my Jetson Pro I followed your instructions and it worrked exept that my bike was maxing 21 km and it went up to 25km/h for unknown reasons even if set to 30km. Good job and thank you!
I have one. Love it! Only thing is the small tires, that won't make it up a small curb, driveway lip, sidewalk, without twisting & throwing me off. I literally have to come to a complete stop, lift the bike onto the curb, then start back up again.
I got this to work today, but it took me and hour an a half, and 3 attempts. For anyone trying this, don’t fully put the case back on (just about half the screws) because it will save you SO much time if it doesn’t work the first time. 😊
Great content and if you have any suggestions on how to pass the 19 mile explain what I need to do so I could do it thank you. I’m by the way I’m 48 years old and yeah, I should’ve looked into electric bikes a little more before I got this one because a lot of the other electric bikes got More accessories than I do so I have to get the accessories and upgrade, but I love the bike though have fun. It’s just to be faster. It’s just my nature. I think it is everybody. I just don’t wanna ruin my bike. You know what I mean, I mean, it was a good price. I could probably get another one you know but no, thank you on the video
I weigh 226 pounds and I'm 6ft 3" tall. I was getting a top speed of 19km/h on flat ground before I did the hack and now I get 23km/h on flat ground. Though it's not the improvement I was hoping for, I'll take what I can get. I hope this is helpful to the other giants my size. Thanks for the tutorial.
Question, I just heard today. Can you use a 48 volt battery instead of a 36 volt battery, do the Speed Hack, and obtain a speed of 22 mph? Several riders mentioned this on the Facebook page today, and said you could use the Standard Controller and Motor. Is this true?
Help me out. I cannot get a speed increase in the bike. I loaded code, checked connections, loaded code to the bike and got the two flashes of the headlight. I've tried a few times without luck. Any advice ??
Well, I did this and hooked it up, saw the light flash twice and thought, great, good to go. However, when I rode it, the most I could get is 14mph pedaling. I'm about 169lbs. So either it didn't work or I have some defect. The head light blinked so it ran the code but didn't seem to make a difference:(
Same situation. I'm wondering if the bikes are too new and the software has been updated to eliminate this work around? Plugging in the elegoo board work. I was even able to slow the bike to 8 mph, it just will not exceed 14mph.....
Thank you for making this video because I just got up my Jetson j5 and and it doesn’t have any lights for this hack so I guess I still do the hack and then just press the red button just in case and see if it works?
Great video. So can this be accomplished using a Mac? On another note, can this be performed on the Jetson Haze? I have two Pros but considering getting the Haze.
What does one headlight blink mean? I tried this hack tonight and that’s all it did - no two blinks. Thanks in advance! And thanks for putting together this awesome tutorial!
Hi, I just wondering do you know? Could you make this sort of bike go any faster DISPATCHED DYU AIF 16" Folding Electric E-Bike, 36V, 7.5Ah, 250W Motor,
Great tutorial! You've got a new subscriber in me! I did have one question though. I know that breadboard wires are just 22AWG solid conductor wires of which I already have TONS. I don't need to buy more wires, do I?
hi, nice tutorial. quick question if i can use the exact same code on Arduino NANO EVERY? i have that in my hand and to my understanding, it will be the same, just need to be careful where the new location of the digital 3 pin? Many thanks!
Thanks! - Can you send me the link on adding an external battery to the Bolt Pro? What size batter is it that lets it go 21mph? Also, have you ever done a hack that lets the Jasion EB7 go faster than 20MPH with throttle only? I need one! TY so much! You are awesome!
Hi! Do we need to buy 3 separate breadboard wires or do they come with your recommended arduino board? Also, do you have any videos on how to put the code onto the board? I am not super familiar with arduinos.
Great video ! I think Jetson might have released a new controller model or it is now shipped with a different version because I have done what the video says and got the double flashing at the end but the bike is still limited to 25Km/h.
I tried this on a newly bought Jetson Bolt Pro from Costco, the headlight flashed twice, I also reset the arduino board to make sure, and same result on the lights, but when I tested, the mileage did not change to 19mph. I read from other comments that this hack no longer works on newer versions of the Jetson Bolt Pro. Is this true? Thank you!
I did this on a Bolt Pro I bought on July of 2021 and it DOES work. However it doesn’t go 19 MPH even when you set it to that. It goes around 16.5-17 MPH which is still an improvement from 13-14 MPH
I tried this on my stock Jetson Bolt Pro- So here is the thing...... It works- but the speed does not change in the real world. If I spin the wheel it does go up to 19, and eventually slowly picks up to 21 mph. But when I put my weight on it, im back limited to like 15mph. Not just that But I played around with this code for a whole week.. Ended up getting a small OLED , and programmed the speeds that has 3 Speed profiles. That way my kid can use it. 6mph 12mph and 19MPH Max. LIke it said It took so much testing , but it works...you just need a better battery.
just did this hack and not seeing much difference, went from 13.5 mph to 15 mph. I did change the value to 8 mph limit to confirm it's loading properly and it did decrease the max speed. Tried increasing the value to 23 mph and got the same top speed of 15 mph so seems like it's the hardware limit.
@@chieutran4329 Hello Chieu, The link is in the video description, and you can also find it here: www.quillsdigest.com/post/jetson-bolt-pro-speed-hack - Tony Quill
@@TonyQuillMagic Hi Tony, I just received the Elegoo Uno R3, just exactly what you have shown in UA-cam. I loaded the file in from the link, and I compare the file I have vs. yours on UA-cam is a little bit different. Anyhow, I just used exactly what I downloaded from the link and try to burn it to Elegoo Uno R3 board, It failed to load to the board and prompt with errors Stray '\302' in program. Can you help please? Thanks
Hi Tony, I am now able to load the update file to Elegoo Uno R3 board without error, I then unload the board to Jetson Bolt Pro and confirmed with head light blinks twice. Speed ride test is improved from 12mph to Max 15mph.
Hi Tony! Thank you for the video tutorial! Very clear explanation! I have two Jetson bolt pro, one is 2021, and the other is Oct 2022. My 2021 JBP worked!! but the Oct 2022 didn't work. Is there a separate code for Oct 2022 JBP? Thank you!
Reading through other comments, it seems that you have to change the line AGREE_TO_TERMS from "FALSE" to "TRUE", on the other variable (line 54 on his video, at 5:42). Also, click the reset button on the board so you can see the light blink twice. Hope this solves your issue!
Tony I just bought 2 Bolt pros, one for me and one for my wife. We did the update but saw no increase in speed. Is there something different in the code of the newer bikes?
Assuming a flat surface, speed is relative to how heavy the rider is and tire pressure (friction). I don't think this bike has any way to measure speed so what is this hack actually doing? Is it allowing the motor to have more current or spin faster? If so the speed increase is mostly relative to the rider weight. For example I weigh about 180lbs and the max speed I can ride is 12 mph. Since I can't get to 15 mph to begin with, I'll never be able to achieve 19 mph. So will this hack enable me to get up to maybe 15 mph, roughly increasing the top speed by 3 mph? If this is just increasing the max speed from 15 mph to 19 mph and not doing anything to increase the power to the motor than the hack is useless to anyone who can't achieve 15 mph to begin with. I just ordered a board so I will try it and report back. UPDATE: Completed this and I got a slight boost in speed, before it would max around 11-12 and now it maxes around 13-14. Good enough for me, don't think I would want to go over 15mph anyway.
The hack is taking away the limit set to 15.5mph for EU ruling. What you can actually get after that will depend on what the motor can do, Or what the controller can do etc..
Hi Tony, if I buy the "ELEGOO UNO Project Super Starter Kit with Tutorial, 5V Relay, UNO R3, Power Supply Module, Servo Motor, 9V Battery with DC, Prototype Expansion Board, ect. for Arduino" do I still need to buy the breadboard wires? Thanks
Is there any way this will work for other similar e scooters? I have a phantom gogo r1 (not the exact scooter but my model was discontinued and removed from the sellers website) I want to know if I can do this same hack with that scooter
Easy to understand video but I did everything required got the 2 blinking lights reset just to make sure got it again and still get same top speed. Should I change the 19mph max to 25 or something or is there something I may have missed? Thanks in advance.
I'm trying to use this hack but when I get to the stage where I plug in the elegoo board it does not even recognize it. Is it the board that I got or am I doing something wrong??
How are you doing? I am subscribing and I just want to say I’m trying to understand how to get the code. How do you get the to the page where the speed limit is? I got the board I got the wires. I got my laptop windows. I don’t know what I’m doing wrong, if this any possible way, you can possibly explain it to me thank you anyway I’ll keep watching your video over and over. I’ll try and get it. I really will but thank you for putting it there because it’s the most I’ve ever seen anybody through this show somebody thank you
This looks easy and straight forward, great tutorial! Will I be able to revert the code back to factory settings afterwards? If so, any chance that you can post a link to the original settings so I can download them for future use. Thanks!
Hello Eren, Since the code is still intact, to revert this hack you would just set the MPH to 15, then repeat the same process. The code looks complicated but it’s pretty much just changing one variable in the Jetson code. Thanks for watching!
How do you make this work on a newer jetson bolt pro model (built in 2022)? The light flashes once then when I click reset it flashes twice but the speed stays the same.
Hey Tony, I was just wondering that what programming language did you use for the Jetson pro? I have further more questions but hope you answer this one. Please answer.
It worked.. i was afraid to damage my jetson pro… $300 is alot of money for me,, so i weight about 138 pounds, before the hack im was going 12.5 mph after the hack it jumped to 15 mph . It is set to 19 in the script but your weight has an impact.. using my iphone to see my speed. One thing the youtube does not explain well is how you download the script. After installing the client, If you right click on the script file from the webpage and save, and import the file it won't work. To make it load into the board i just created a new script and copy pasted the whole script into the new blank script..then i saved the file. Then i imported my new created file. Then i uploaded it to the board. On your bike, i used a dentist pick to remove the plugs and disconnected the battery. Connected the board exactly as shown in this video and turned on the bike, first time it did not work, took me few min to figure why.. connection issue only ,,, so make sure all the wires are well connected.. it should work.. Ok im not getting 19 mph.. but 15 mph from 12.5 mph is 2.5 mph increase… im happy with that especially that i sometime carry my 6yrs daugther on a small kid seat i added to the jetson. Which bring a total weight of 160+ pounds easy
Hey there, not sure if you're still checking comments on this vid. But I'm in the process of doing this mod for my son and for some reason the Elegoo Uno R3 board isn't showing up as an option when I plug it into my computer. I've tried two different computers and neither of them even show the board as connected to my computer. Any suggestions?
This is a wonderful hack, my son said he wanted to go faster on his bike so he decided to do this, the results are great, the hack works, this great video helped a lot.
When did you by the bike ?
People are saying this doesn’t work if you got the bike in 2021+. When did you buy it?
@@GTheLegendOfficial damn, I was gonna try this but I just bought the bike 2 days ago.
@@obl1xif_y981 I did this to my bike i got in July of 2021 and it increases the max speed to around 16.5-17 MPH (throttle only). I commented before i did the hack.
I can't get the rubber things back in
Hi Tony. Fantastic mod. I've added just about every mod out there to my Jetson, including being able to carry and easily change out three batteries for long rides. However, until now I've held off on hacking the speed control because I wanted a simple, cost affective solution that didn't add more clutter. So your solution checks all the boxes for me. It's the best electric out there for fun on the trails. Thanks again for sharing your engineering skills with all us Jetson Bolt Pro fans. I'm a new subscriber for you and I will keep watching for more of your ideas.
Hello D Hoffman,
I’m glad that this solution works out for your Jetson Bolt Pro. It really is an amazing electric vehicle! Thank you for the subscribe, it really means a lot to me!
Swagger 5 Hack has never been done and has been sought after since the first M365 hack
Where did u get the 3 batteries to replace tha one that came with bike when dead? N wut batteries r they
Wait so do you know how to program if so what language, so it's just engineering and computer science right for this kind of stuff.
Hi D Hoffman, what generation is your Jetson bolt Pro. Did the hack work for you to reach speeds at 19 miles per hour.
I used this process last week to update my daughters Jetson Bolt Pro in addition to adding a parallel battery, 60T chainring, and folding pedals. What a difference. Now that little bolt can keep up with our full sized ebikes. It goes around 16-18mph with my 10 year old with a little pedaling and we went 19 miles and it only used 1 bar. The second battery is 10.6ah giving it around 17ah at 36V nominal. We passed some stock Jetsons on the bike path and it was quite a difference in speed.
Hello Nathan,
I’m glad the hack worked out for you! Thanks for watching!
Do I need to replace the chain at the same time, because the 60t needs a longer chain?
@@longtan9259 Yes, you need to buy a single speed chain, or add links to the existing chain with a chain breaker.
Hey Nathan I just bought one can I email you about the upgrade I plan on doing that to mine thank uou
where did you get the board from? There is no link
For anyone considering doing this speed mod, here's my experience. You will probably need a bigger chainring to increase the gearing to compensate for the added power. Even at lower speeds, I found my gears were constantly spinning and not giving me enough resistance from pedal assist. For those only wishing to use throttle power, this would be fine. But I wanted to keep my pedal assist to give me some more exercise and to give me more range.
If you care about exercise, maybe consider disabling pedal assist. I know there are many great tutorials on how to do it and it will give you more speed when you pedal!
@@super73uk do you know if the hack in the video can be made even for the dyu d3f model? Thanks
@@angelor6899 Hi & thank you for your question.
Yes it should work fine as both bikes are basically the same (Made in the same factory by the same company). The DYU is made by a company called "F-wheel" who also sell the bike to other companies who then put their own badge on it, i.e. "Jetson". Not sure if you know but there is also a reddit page for the bikes where there is loads of info worth reading.
why would you get an ebike for exercise? just ride a regular bike? The pedal assist is just working better with the added power, its literally just assisting you more. Your gears spin whenever you pedal, thats how gears work, so I'm not even sure what your trying to say?
@@InZayne Everyone's different brotha, don't think too hard
used this mod and it worked! I am able to go around 18 mph, I'm seeing in the comments that some of the newer models of the bike do not work with this mod so if you have bought the bike recently I wouldn't recommend trying this out.
I think you are correct. I just bought mine last weekend and did the mod but no change in speed between my pre and post test. I already had the Arduino board so it was only 20 min of my time to try.
@@CrypttedDags same :/ , tried last week and although my bike light flashed twice my max speed is 15mph
What is the date of the JBP? It should say on the handle bar on one of the stickers
Finished my wife's ebike today. Unbelievable. It work! Thanks bro. Need a hack for my Ecotric fat tire bike now.
Done, Thanks ! 32km with back wheel in air, Kugoo V1.
If hack didn't work u need to replace/rewrote False to True in agree arrangement which is in the sketch right under to 19th mile line
where
I was able to use this hack, i adjusted the speed to 20 and tested and 22 and tested, on a straightway there was no difference but it does add about 3-4 mph for sure!
Thanks. It works. I've set it to 23mph. When the bike reaches 22-23 it starts reducing speed, which can be felt especially on a downhill. But I also did shunt mode and installed 48v 10Ah battery. I also have two fans inside the case to prevent overheating.
I wrote the program for the speed hack. For those wondering "Why am I not getting 19 mph when I set it to 19 mph" : This hack programs the controller to attempt 19 mph, but without upgrades to the battery (adding another battery in parallel to be able to push more amps) it may not be achievable and instead you will only see a slight improvement. Just the same as when the battery state of charge is low you will notice it has less power and speed.. or when you throttle and you see the bars on the display drop from 3 bars to 1 bar - the battery is the weakness to achieving the desired speed.
Thank you for making a video tutorial about the program to get it out to more people that wish to do it and playing customer service- I was getting a lot of comments asking how to do it which has stopped now thanks to you! Also, I just updated the program today to be more constant at verifying the hack has been complete - watch for 2 blinks of the headlights.
Does it still work on the latest batch of these bikes?
Does this work for dyu df3
What does one headlight blink mean? I tried this hack tonight and that’s all it did. Thanks in advance!
@@puresim316nosimracingnolif3, I would also interested in knowing if this would work on a DYU D3F
so should i start by getting a 48v battery
Thank you, i bought the board you showed, made up some wires to connect it and upped the speed to 20 mph all through watching your video.
Im so pleased.
P.s. i do have a faulty throttle but that was like it before anyway.
Where did you find the source code ????
I just scored five of these Bolt Pros at Costco yesterday for the family and I. What a blast... Even more now that I ran across your video and was able to successfully reprogram a few of them (getting late here now) tonight for quite an improvement. I'll have to GPS each of us and see how quick they really are. Thanks for this video!
I saw them today at Costco for $279! Go back and get your 30 day price guarantee!
@@richardmr2 thanks Richard. That’s the price I got them for. Good looking out!
I just purchased one from Costco and I wasn’t able to do the speed hack, I did all the steps and got the two blinks from the headlight but still is only limited to about 14 on flat ground. Any ideas?
@@dylansessions9027 mine too and got mine last year from Costco (5/2021) build date. I don’t know how these recently purchased Jetson bikes are taking the hack unless they are NOS…
After watching this I ordered the bike and Arduino. My e-scooter has similar specs and price but it's hard on the knees after 30+ minutes and I'd like to burn some more calories. Cheers!
I borrowed a Jetson Bluetooth module to do mine last fall, but I just picked up a 2nd Bolt Pro for my wife, and I will be doing this to mod her speed.
Thankyou so much for the video !
If there was a service that did this, I'd rather pay someone to do it.
where could we go for it to done
Great tutorial that was to the point, worked exactly how you mentioned even though I used an off brand Elegoo Mega2560 that I've had laying around unused for years - everything lined up 1-to-1 perfectly from your instructions and the Arduino site and agent work with it too.
Thanks! Got two headlight flashes the very first try because of you.
Can you still use pedal assist
I second the question, can you still use pedal assist after the hack?
@@LLF1234 yes
Thank-you for your videos on JETSON Bolt . Because of the upgrades you have encouraged us to buy a JETSON! I can hardly wait to ride the e-bike! -Angèle
When i buy the controller board and wires do I still need them or is it just a one time thing and dont use them after?
Really good mod. On my Jetson Pro I followed your instructions and it worrked exept that my bike was maxing 21 km and it went up to 25km/h for unknown reasons even if set to 30km. Good job and thank you!
When did u buy ur jetson because some people are saying it won’t work on newer ones
@@gurnoorjhajj710 it doest
My boyfriend and I have a set of Jetsons. I am going to modify mine with out hom knowing lol. Can't wait 🚴♀️
I have one. Love it! Only thing is the small tires, that won't make it up a small curb, driveway lip, sidewalk, without twisting & throwing me off.
I literally have to come to a complete stop, lift the bike onto the curb, then start back up again.
Bunny hop the curb
Did speed hack work
I got this to work today, but it took me and hour an a half, and 3 attempts. For anyone trying this, don’t fully put the case back on (just about half the screws) because it will save you SO much time if it doesn’t work the first time. 😊
Glad you had success! I tried it on my Jetson Pro but still the same speed. How did you make it work?
2022 bike?
@@TheNyzzler I did see some speed change from 13-14 max to 16-17. My bike is a 2021 Jetson Pro.
@@TheNyzzler yep got it at costco about 2 months ago
What did you do on the third attempt to get it working?
Cool video, I'm thinking about getting one of these bikes and this makes it way more appealing.
Great content and if you have any suggestions on how to pass the 19 mile explain what I need to do so I could do it thank you. I’m by the way I’m 48 years old and yeah, I should’ve looked into electric bikes a little more before I got this one because a lot of the other electric bikes got More accessories than I do so I have to get the accessories and upgrade, but I love the bike though have fun. It’s just to be faster. It’s just my nature. I think it is everybody. I just don’t wanna ruin my bike. You know what I mean, I mean, it was a good price. I could probably get another one you know but no, thank you on the video
I weigh 226 pounds and I'm 6ft 3" tall. I was getting a top speed of 19km/h on flat ground before I did the hack and now I get 23km/h on flat ground. Though it's not the improvement I was hoping for, I'll take what I can get. I hope this is helpful to the other giants my size. Thanks for the tutorial.
Question, I just heard today. Can you use a 48 volt battery instead of a 36 volt battery, do the Speed Hack, and obtain a speed of 22 mph? Several riders mentioned this on the Facebook page today, and said you could use the Standard Controller and Motor. Is this true?
Help me out. I cannot get a speed increase in the bike. I loaded code, checked connections, loaded code to the bike and got the two flashes of the headlight. I've tried a few times without luck. Any advice ??
Well, I did this and hooked it up, saw the light flash twice and thought, great, good to go. However, when I rode it, the most I could get is 14mph pedaling. I'm about 169lbs. So either it didn't work or I have some defect. The head light blinked so it ran the code but didn't seem to make a difference:(
Same situation. I'm wondering if the bikes are too new and the software has been updated to eliminate this work around?
Plugging in the elegoo board work. I was even able to slow the bike to 8 mph, it just will not exceed 14mph.....
Have you tried they Bluetooth hack yet ?
@@MosOneFPV I don't have bt module from non pro bike to try it.
Exact same thing here, seems like such a cool hack but apparently doesn't do much of anything. Gonna set it to 7mph and see if it slows dowb as well.
Yeah this hack didn’t work for me. Waiting for a response from him.
Thank you for making this video because I just got up my Jetson j5 and and it doesn’t have any lights for this hack so I guess I still do the hack and then just press the red button just in case and see if it works?
Does it matter if it's that brand of board? Because Amazon has other ones for way cheaper in price.
Just did this hack on my Bolt today, and it worked:) thank you
Great video. So can this be accomplished using a Mac? On another note, can this be performed on the Jetson Haze? I have two Pros but considering getting the Haze.
Yes, I just did it using a Mac
What does one headlight blink mean? I tried this hack tonight and that’s all it did - no two blinks. Thanks in advance! And thanks for putting together this awesome tutorial!
This was such a good find!!! Thanks for this tutorial! You are a good teacher btw! Look forward to more videos from you! :)
Hello Tim,
Thank you so much for watching, I appreciate your support :)
Nice vid, does this software work on a Mac? Just picked up a bike on offer up, notice it lags while going up hill let me know, thanks
Hi, I just wondering do you know? Could you make this sort of bike go any faster DISPATCHED
DYU AIF 16" Folding Electric
E-Bike, 36V, 7.5Ah, 250W Motor,
does increasing speed really affect how long the motor can last ?
I purchased a refurbished one so far i like it.
Does it work on the Haze?
Well done video. Thank your for the easy to follow instructions. It worked like a charm!
Thank you, Legend. It worked beautifully.
Worked as advertised, thanks Tony
is this also work with urban glide 140? and one more question how can you get the controller's data where you can change the speed it? please answer
I am not experienced with uploading stuff onto arduino board I can’t write code
Great tutorial! You've got a new subscriber in me! I did have one question though. I know that breadboard wires are just 22AWG solid conductor wires of which I already have TONS. I don't need to buy more wires, do I?
hi, nice tutorial. quick question if i can use the exact same code on Arduino NANO EVERY? i have that in my hand and to my understanding, it will be the same, just need to be careful where the new location of the digital 3 pin?
Many thanks!
Thanks! - Can you send me the link on adding an external battery to the Bolt Pro? What size batter is it that lets it go 21mph? Also, have you ever done a hack that lets the Jasion EB7 go faster than 20MPH with throttle only? I need one! TY so much! You are awesome!
Do you have a Speed Hack for the Jetson Haze?
Hi! Do we need to buy 3 separate breadboard wires or do they come with your recommended arduino board? Also, do you have any videos on how to put the code onto the board? I am not super familiar with arduinos.
its in the video how to do but you need to buy cables and most Jetsons will only go 15/16 will not go to 19 or 20 mph
Does this work for DYU D3 as these wires not available in the box
Can you also use a ST-32 link for this ??
Great video ! I think Jetson might have released a new controller model or it is now shipped with a different version because I have done what the video says and got the double flashing at the end but the bike is still limited to 25Km/h.
Following, since I plan to get one in the next couple of days.
Yes I just tried to do the hack as well and still am only getting about 14mph. Anybody have an update on how to mod the newer Jetson pro?
Not working for me either. Light flashed once
What your bike built date ?
@@weiz2493 how do I find that out?
I tried this on a newly bought Jetson Bolt Pro from Costco, the headlight flashed twice, I also reset the arduino board to make sure, and same result on the lights, but when I tested, the mileage did not change to 19mph. I read from other comments that this hack no longer works on newer versions of the Jetson Bolt Pro. Is this true? Thank you!
Does this work on a recently bought refurbished Jetson Haze?
I did this on a Bolt Pro I bought on July of 2021 and it DOES work. However it doesn’t go 19 MPH even when you set it to that. It goes around 16.5-17 MPH which is still an improvement from 13-14 MPH
Same here. I'm considering upping the MPH to between 21-22 to get closer to 19 MPH
Mine only goes 15 lol
@@Shutrbug69 did it work?
@@vnetcorp560 stop being so damn thirsty smh
Mine too i see 17 max. But still good
I tried this on my stock Jetson Bolt Pro- So here is the thing...... It works- but the speed does not change in the real world. If I spin the wheel it does go up to 19, and eventually slowly picks up to 21 mph. But when I put my weight on it, im back limited to like 15mph.
Not just that But I played around with this code for a whole week.. Ended up getting a small OLED , and programmed the speeds that has 3 Speed profiles. That way my kid can use it.
6mph
12mph and
19MPH Max.
LIke it said It took so much testing , but it works...you just need a better battery.
What battery would you need
Regarding the plug you put the pins into, was that not plugged into anything originally, or did you disconnect something?
Hello. Does this work with the dyu d3f?
Also. If the hack doesn't work, can i return the bike to factory settings?
Thanks.
just did this hack and not seeing much difference, went from 13.5 mph to 15 mph. I did change the value to 8 mph limit to confirm it's loading properly and it did decrease the max speed. Tried increasing the value to 23 mph and got the same top speed of 15 mph so seems like it's the hardware limit.
it's because the new jetson bolt has a hardware limiter
@@vnetcorp560 Before ordering parts to mod my jetson, do you know how i would know if my Bolt is eligible for this mod? Thanks!
@@friedrice30 if your bolt is from last year
@@vnetcorp560 I just checked and mine was produced 09/2021. Safe to say I can apply this mod to my Bolt?
@@friedrice30 it should work since my 2022 model did not
Great video.
Will this allow more torque to the motor? :Half way up hills is a bummer :-/
Just making sure, the original value of the speed should be 15.5 instead of 19 correct? In case I want to undo the changes for better battery.
Tried it and worked no problems. Thanks for the video.
Hey Paul,
Glad to hear you got the speed hack working!
How do you get the Jetsonspeedhack file? Thanks
@@chieutran4329 Hello Chieu,
The link is in the video description, and you can also find it here: www.quillsdigest.com/post/jetson-bolt-pro-speed-hack
- Tony Quill
@@TonyQuillMagic Hi Tony,
I just received the Elegoo Uno R3, just exactly what you have shown in UA-cam. I loaded the file in from the link, and I compare the file I have vs. yours on UA-cam is a little bit different. Anyhow, I just used exactly what I downloaded from the link and try to burn it to Elegoo Uno R3 board, It failed to load to the board and prompt with errors
Stray '\302' in program. Can you help please?
Thanks
Hi Tony, I am now able to load the update file to Elegoo Uno R3 board without error, I then unload the board to Jetson Bolt Pro and confirmed with head light blinks twice. Speed ride test is improved from 12mph to Max 15mph.
Hi Tony! Thank you for the video tutorial! Very clear explanation! I have two Jetson bolt pro, one is 2021, and the other is Oct 2022. My 2021 JBP worked!! but the Oct 2022 didn't work. Is there a separate code for Oct 2022 JBP? Thank you!
Reading through other comments, it seems that you have to change the line AGREE_TO_TERMS from "FALSE" to "TRUE", on the other variable (line 54 on his video, at 5:42). Also, click the reset button on the board so you can see the light blink twice. Hope this solves your issue!
Are you working on the speed mod for the Jetson Haze
amazing, this just made my commute so much faster!
Tony I just bought 2 Bolt pros, one for me and one for my wife. We did the update but saw no increase in speed. Is there something different in the code of the newer bikes?
Hey just wondering can I do all this stuff on a Chromebook?
Hey Tony!
2 questions:
1. What year is your Jetson Bolt Pro?
2. How much do you weigh?
Thank you!
Man, thanks a lot. You have opened an entire world to me
Assuming a flat surface, speed is relative to how heavy the rider is and tire pressure (friction). I don't think this bike has any way to measure speed so what is this hack actually doing? Is it allowing the motor to have more current or spin faster? If so the speed increase is mostly relative to the rider weight. For example I weigh about 180lbs and the max speed I can ride is 12 mph. Since I can't get to 15 mph to begin with, I'll never be able to achieve 19 mph. So will this hack enable me to get up to maybe 15 mph, roughly increasing the top speed by 3 mph? If this is just increasing the max speed from 15 mph to 19 mph and not doing anything to increase the power to the motor than the hack is useless to anyone who can't achieve 15 mph to begin with. I just ordered a board so I will try it and report back.
UPDATE: Completed this and I got a slight boost in speed, before it would max around 11-12 and now it maxes around 13-14. Good enough for me, don't think I would want to go over 15mph anyway.
The hack is taking away the limit set to 15.5mph for EU ruling. What you can actually get after that will depend on what the motor can do, Or what the controller can do etc..
Will this work with the jetson bolt pro 250 watt?
I believe I have uploaded the code twice by mistake to the arduno board... will this mess up the bike if I upload now?
Hi Tony, if I buy the "ELEGOO UNO Project Super Starter Kit with Tutorial, 5V Relay, UNO R3, Power Supply Module, Servo Motor, 9V Battery with DC, Prototype Expansion Board, ect. for Arduino" do I still need to buy the breadboard wires? Thanks
Does this also apply to the Jetson Atlas E BIKE?
Is there any way this will work for other similar e scooters? I have a phantom gogo r1 (not the exact scooter but my model was discontinued and removed from the sellers website) I want to know if I can do this same hack with that scooter
This guy is the future of youtube
I had a question would you be able to do this speed hack with the jetson axle 12”?
Hey man! great tutorial! when i get mine i will be doing that ASAP!
Thank you for your upload and the code to be able to copy and download and upload! I really appricate it! 😁
Easy to understand video but I did everything required got the 2 blinking lights reset just to make sure got it again and still get same top speed. Should I change the 19mph max to 25 or something or is there something I may have missed? Thanks in advance.
Does it work the same for the regular jetson bolt without the pedals
I'm trying to use this hack but when I get to the stage where I plug in the elegoo board it does not even recognize it. Is it the board that I got or am I doing something wrong??
try using different brewer also doesn't work on models newer then 2022
How are you doing? I am subscribing and I just want to say I’m trying to understand how to get the code. How do you get the to the page where the speed limit is? I got the board I got the wires. I got my laptop windows. I don’t know what I’m doing wrong, if this any possible way, you can possibly explain it to me thank you anyway I’ll keep watching your video over and over. I’ll try and get it. I really will but thank you for putting it there because it’s the most I’ve ever seen anybody through this show somebody thank you
Hi Tony, does the code need to be set to “true” for the code to work?
I’ve opened a Jetson Haze model, looks the same. 👍🏽👍🏽Works with Haze model?? Any idea ? Thanks thanks
Possibly, if the Bluetooth port has the same colored pins, I believe it should work. Maybe I'll purchase a Haze from Costco to try it out one day.
does this also work on the normal jetson bolt with red wheels?
I hacked my Jets on Bolt Pro on the first try thanks to Tony! You made it simple and easy!!
Hello Larry,
I'm glad you got it to work, have fun with your upgraded Jetson!
Does the hack truly increase the speed to 19 mph?
will this work the same way for the DYU D3F??
I dont see an empty bluetooth connector on bike purchased in May 2022. Did the company take the bluetooth connector out?
do you know if it's unsafe to put 20 instead of 19? i feel like if it's 19 you might as well make it 20
This looks easy and straight forward, great tutorial! Will I be able to revert the code back to factory settings afterwards? If so, any chance that you can post a link to the original settings so I can download them for future use. Thanks!
Hello Eren,
Since the code is still intact, to revert this hack you would just set the MPH to 15, then repeat the same process. The code looks complicated but it’s pretty much just changing one variable in the Jetson code. Thanks for watching!
@@TonyQuillMagic I been watching your videos and where do I find the code for the speed hack
@@esmooth2125 me too i checked the written link code and the it says link coming soon where is the code?
Have you added new brakes to your bike? I find that the brakes are really bad even at 15 mph.
Did the hack but bike Maxes out at like 14-15 even though i set it to 19 im 5'8 at 165 should i add more speed or leave it?
How do you make this work on a newer jetson bolt pro model (built in 2022)? The light flashes once then when I click reset it flashes twice but the speed stays the same.
Or built in 2021 not sure
Hey Tony, I was just wondering that what programming language did you use for the Jetson pro? I have further more questions but hope you answer this one. Please answer.
Hello, does this work on the Jetson Haze too? Thanks
It worked.. i was afraid to damage my jetson pro… $300 is alot of money for me,, so i weight about 138 pounds, before the hack im was going 12.5 mph after the hack it jumped to 15 mph . It is set to 19 in the script but your weight has an impact.. using my iphone to see my speed.
One thing the youtube does not explain well is how you download the script. After installing the client, If you right click on the script file from the webpage and save, and import the file it won't work. To make it load into the board i just created a new script and copy pasted the whole script into the new blank script..then i saved the file. Then i imported my new created file. Then i uploaded it to the board.
On your bike, i used a dentist pick to remove the plugs and disconnected the battery. Connected the board exactly as shown in this video and turned on the bike, first time it did not work, took me few min to figure why.. connection issue only ,,, so make sure all the wires are well connected.. it should work..
Ok im not getting 19 mph.. but 15 mph from 12.5 mph is 2.5 mph increase… im happy with that especially that i sometime carry my 6yrs daugther on a small kid seat i added to the jetson. Which bring a total weight of 160+ pounds easy
Just did this and got up to 17mph while pedals but spin out... Has any replace to a bigger chainrain and if so what size works best thanks
Hey there, not sure if you're still checking comments on this vid. But I'm in the process of doing this mod for my son and for some reason the Elegoo Uno R3 board isn't showing up as an option when I plug it into my computer. I've tried two different computers and neither of them even show the board as connected to my computer. Any suggestions?
Thanks! I have an Arduino laying around.