I just ordered my motors arduino and motorcontrollers to build my first 2DOF FlyingCarpet :) Thank you very much for the detailed exlanation of SimTools. I think that info about in/out Games (PC2) at the end will at last be the most important for me. You have a great overall channel there CONGRATs, Later from BAVARiA, Yours ART FLY
Nice video, but for safety, I must say that is not the intended function of the Axis Limiting tab. That is where you set the limit of travel for each axis(motor or actuator) short of where the motor or actuator will bottom out or before your rig would hit something. It then also scales the Min & Max game data to fit inside that limited amount of travel. To smooth motion you have smoothing filters on the forces. To make a ride weaker or stronger for rider preference you have a Max Level of % slider in the Game Manager Profile Editor for each game and also sliders for each individual force if you'd like to fine tune each. This way you can share setups and profiles with others. Axis limiting depends on your rig and shouldn't be shared with another and usually once set you don't change it. You can lower the percentage of travel forces get in Axis Assignments. Doing it this way, the percentages make sense. 100% in Axis Assignments will give that force 100% of the available travel you limited in Axis Limiting. You can then also change the min & max values for the forces in Tuning Center to trim off any unwanted game data.
Hi, I noticed both of your roll in axis assignments are un-ticked and only one of your pitch is ticked. It’s different from what simtools manual and Dofreality manual. Please explain.
Good job at explaining the settings! I definitely appreciate it. I built a similar system and I never even saw the tab for *axis limiting and since mine has 2 dof + TL, i did not even try sway or surge.. I will tomorrow for sure.. Thanks again D
You mentioned when friends are over. I've tried putting people in game, but they can't drive anything in real games. Like, at all. What arcadey titles work with the movement but are approachable by normal drivers? I'd like to have something that is sort of an arcade feeling for those situations (flight and/or driving).
Looking into getting this platform. Thanks for sharing this info, good stuff! Is there a distinction to be made between yaw and traction loss - you seem to use an extra axis for traction loss rather than yaw? Does this mesn the third motor is disabled in xplane - unable to simulate yaw movement in any sense? Thanks!
hello sir! just finished my motion rig and I want to start a driving channel, can you , please, tell me the model of the cameras you use? thank you ! great tutorial!
Hello, I got troubles to make my SERIAL 2 DOF motion working with Assetto Corsa and rally 2.0. I work fine for LFS games but with the other game, game manager and game engine detect de game are running and are on, but no motion at all.
you have a 3 dof and with simtoolls did you put all the mavimientos? It can? I have a 3 dof and configure traction loss, sway and surge, they told me that if I put more movements in those two matores it is not good
Not sure where to go to put in my pro info I have the email address and password but im lost on the sim tools page. Any help would be appreciated. Nothing came up on the download wizard install where I could of entered the info.
can you help me my project is ready and all that i need to work i need to uninstall and format to reinstall td again and get back to work. what will be the problem
Buenas, Yo no compre sim tools por el momento... Pero descargándolo gratis como te deja la pagina puedo hacer prueba de mover los motores?O solo funciona con vercion pro para hacer eso.
I just ordered my motors arduino and motorcontrollers to build my first 2DOF FlyingCarpet :)
Thank you very much for the detailed exlanation of SimTools. I think that info about in/out Games (PC2) at the end will at last be the most important for me.
You have a great overall channel there CONGRATs,
Later from BAVARiA,
Yours ART FLY
Nice video, but for safety, I must say that is not the intended function of the Axis Limiting tab. That is where you set the limit of travel for each axis(motor or actuator) short of where the motor or actuator will bottom out or before your rig would hit something. It then also scales the Min & Max game data to fit inside that limited amount of travel. To smooth motion you have smoothing filters on the forces. To make a ride weaker or stronger for rider preference you have a Max Level of % slider in the Game Manager Profile Editor for each game and also sliders for each individual force if you'd like to fine tune each. This way you can share setups and profiles with others. Axis limiting depends on your rig and shouldn't be shared with another and usually once set you don't change it. You can lower the percentage of travel forces get in Axis Assignments. Doing it this way, the percentages make sense. 100% in Axis Assignments will give that force 100% of the available travel you limited in Axis Limiting. You can then also change the min & max values for the forces in Tuning Center to trim off any unwanted game data.
Hi, I noticed both of your roll in axis assignments are un-ticked and only one of your pitch is ticked. It’s different from what simtools manual and Dofreality manual. Please explain.
Good job at explaining the settings! I definitely appreciate it. I built a similar system and I never even saw the tab for *axis limiting and since mine has 2 dof + TL, i did not even try sway or surge.. I will tomorrow for sure.. Thanks again D
You mentioned when friends are over. I've tried putting people in game, but they can't drive anything in real games. Like, at all. What arcadey titles work with the movement but are approachable by normal drivers? I'd like to have something that is sort of an arcade feeling for those situations (flight and/or driving).
good job man...i have a great plain in my mind...to build my 3DOF on C337 skymaster fuselage...thanks for the explanation
Looking into getting this platform. Thanks for sharing this info, good stuff! Is there a distinction to be made between yaw and traction loss - you seem to use an extra axis for traction loss rather than yaw? Does this mesn the third motor is disabled in xplane - unable to simulate yaw movement in any sense? Thanks!
hello sir! just finished my motion rig and I want to start a driving channel, can you , please, tell me the model of the cameras you use? thank you ! great tutorial!
Hello, I got troubles to make my SERIAL 2 DOF motion working with Assetto Corsa and rally 2.0. I work fine for LFS games but with the other game, game manager and game engine detect de game are running and are on, but no motion at all.
Where do I find out what comport my DOF h3 is using?
I have the pro edition of simtools, where can I get Drift4 plugin so I can test it ?
can RSRBR 2021 or any of the previous version works with Simtools or SimRacing Studio software for motion simulator?
you have a 3 dof and with simtoolls did you put all the mavimientos? It can? I have a 3 dof and configure traction loss, sway and surge, they told me that if I put more movements in those two matores it is not good
Not sure where to go to put in my pro info I have the email address and password but im lost on the sim tools page. Any help would be appreciated. Nothing came up on the download wizard install where I could of entered the info.
Hello first off thanks for your videos ! Next where can I find the x plane 11 plugin for simtools?
Do you get a good road textures and bump feeling or you rely on transducer for this?
can you help me my project is ready and all that i need to work i need to uninstall and format to reinstall td again and get back to work. what will be the problem
Buenas, Yo no compre sim tools por el momento... Pero descargándolo gratis como te deja la pagina puedo hacer prueba de mover los motores?O solo funciona con vercion pro para hacer eso.
I cant get my DOF Reality p3 to work at all and it wont let me click on interface settings. ive been working on this since I got it 3 days ago.
hello, please help me to understand this program. how to add a game and set it up in sim tools
Hi mate, can you share axis assignments and the tuning center for Elite Dangerous?
Why Scn5 connect to RS485 to USB nothing move in Simtool. Im use window 10
I purchased the plugin can you share your x plane 11 preset for the dof reality rig please
my game manager not connected live for speed,please
How can u get GTA V in Simtools
i cant my rig to work at all
Yeah I'm lost I can't get mine to cooperate at all lol
Can't get what to cooperate
Well at least you use the best software
SimRacingStudio is way more easy to use with DOF reality and it comes with the purchase of the rig.