SKIL Portable Jobsite Table Saw (TS6307) Setup and First Cut

Поділитися
Вставка
  • Опубліковано 26 лис 2024

КОМЕНТАРІ • 31

  • @Stargate555
    @Stargate555 Місяць тому +1

    Step by step assembly. Perfect instructional video, Thank You.

  • @timmcwilliams8024
    @timmcwilliams8024 7 місяців тому +10

    Directions are worthless …This was great! Didn’t skip any steps, didn’t play any stupid music in the background that’s irritating as crap!! And is the updated version of the saw with the change riving, knife. Big help thank you 🙏

    • @SomethingIsAlwaysGoingOn
      @SomethingIsAlwaysGoingOn  7 місяців тому +1

      Happy to hear that :)

    • @beacon-313
      @beacon-313 Місяць тому

      I came here to You Tube because the directions are trash. Someone got PAID to write the directions! LOL

  • @CBBC435
    @CBBC435 5 місяців тому +4

    Finally, a good video on this saw.

  • @george230
    @george230 2 місяці тому +1

    U have the best set up video on utube. Great job.

  • @darrinmcelroy9941
    @darrinmcelroy9941 3 місяці тому

    I wish I had seen this literally yesterday. I should have searched before setting mine up. The directions for setting up the blade guard leave a lot to be desired. I also realized that once I finally figured it out it would be easy as hell. It was just that first time getting it on.

  • @JoeNorero
    @JoeNorero 2 місяці тому +1

    I want to add a note to the very fist step of installing the included knob which is not attached. Only one side of the hex key is used it is the short elbow side of the key. I was able to install this better by putting the screw on the hex key first then putting the knob over the bolt and attach it to the saw. This made it possible to not need to try to get it on the hex key while trying to find the thread on the saw where the bolt goes and get it threaded. I know this is common sense but I wanted to add this simple step so someone else to get it done easier on the first go.

  • @brentnance5873
    @brentnance5873 4 місяці тому +1

    Awesome, simple yet very effective video. Thanks.

  • @XiphosGladius
    @XiphosGladius 6 місяців тому +2

    Simple and easy to follow video.

  • @DaraHijazi
    @DaraHijazi 2 місяці тому

    Thanks for the video

  • @TNRonin
    @TNRonin 2 місяці тому

    Good vid!

    • @SomethingIsAlwaysGoingOn
      @SomethingIsAlwaysGoingOn  2 місяці тому

      Thanks

    • @TNRonin
      @TNRonin 2 місяці тому

      Side note: I couldn't figure where to store that hex wrench. It fits the padlock hole on the power switch.

  • @JanisTreijs
    @JanisTreijs 7 місяців тому

    Thanks for the help 👍!

  • @george230
    @george230 2 місяці тому

    Can u rip a 2x4 with this saw.

  • @dadimans2591
    @dadimans2591 6 місяців тому

    This is so helpful. Thanks

  • @jameswatson8609
    @jameswatson8609 2 місяці тому +1

    Verbal communication is key for me sorry

  • @adrianw4021
    @adrianw4021 5 місяців тому

    Thanks broski