Hello, Sir, Al-Suwaij, number two, connects from one side of the Arduino to No. 2 and No. 3 from either side, the D or A, and the other end of the Swij goes to ground
@@BabakStars Thank you, sir. I mean on one side it is connected to the Arduino, and on the other hand it is connected to the ground, i.e. the negative side
Hello. I used two lithium batteries that are connected to the VIN pin of Arduino. It means 7.4 volts. You can watch the next episodes of this project in the channel.
@@BabakStars hmm I can't wait for your video because I have to give this project tomorrow so can you tell me last thing if I used 3.3 v regulator for this project because as you know that nrf would have 1.6 till 3.6 v input voltage so if use regulator would it will be start and last again sorry for that I have issue I just used female to female wires for this project I don't connect any thing with board except only battery connection so if I do this would project work properly or still give me issue on that??
@@SaifKhan-gx9lf I wrote in the description section that this project does not work. But in the second part of this project, I connected the regulator, but I did not get any results.
@@BabakStars ohh no so this jammer will not resist any internet in a single mobile??so why it's is popular in a Arduino projects I got this from the Arduino main page
@SaifKhan-gx9lf Unfortunately, not. I made this at the request of another person. But look at this one.ua-cam.com/video/ewdN5eLwz7w/v-deo.html Could you send me that Arduino main page?
Sorry, this video was my first attempt to make jammer, but I got it from a fake online magazine. Better see the next episodes. Regarding Bluetooth, I don't know what channel it works on.
Hi sir I’m from the uk 🇬🇧 and I really enjoyed your video thanks for sharing it , I’m not a professional like yourself so I have a couple of questions if you could help
Hello sir, sorry if I bothered you, I need your help. The screen that I have is different from the screen in your project. My screen works on the SH1106 library. I tried to replace the library and insert it into the code. I did not succeed. Please help me. How do I replace the SSD1306 library with the SH1106 library?🙏
Hello, you do not need to replace. If you can install the correct library, the display will work fine. Just search for SSD1306 and install the Adafruit SSD1306 library. There are no special settings.
@@BabakStars also does it scan through nearby WIFI connections and then you can select them to jam? By the way, what is the efficient range of the jammer? Of course I won’t use it for anything bad, just for testing
@@BabakStars At the top of the screen, lines appear in width, and at the bottom of the screen, numbers pass by at a speed that I cannot read🙏Screenwriting does not appear as it does in your video
Hello great video, please make some new arduino hacking tool for example Esp32 WiFi Hacking or Kali Linux Hacki g with python or RFID Card read/write or something else. Have a nice day.
Also does it really work?
Hello, Sir, Al-Suwaij, number two, connects from one side of the Arduino to No. 2 and No. 3 from either side, the D or A, and the other end of the Swij goes to ground
Hi, sir. If I understand you correctly, you are talking about the buttons that connect to the arduino? it's true?
@@BabakStars Thank you, sir. I mean on one side it is connected to the Arduino, and on the other hand it is connected to the ground, i.e. the negative side
Yeah. True
@@BabakStars Thank you, sir, and sorry if my questions bother you
@@نشوانالظاهر-م9ف don't mention it
bro, is using three nrf24l01 modules better than one nrf24l01 module, and can this tool block signals or wifi?
Yes. Naturally, you will get a better answer with more modules. But wait for the new video.
Bro, why did mine just turn on when it just said "jamming channel1" even though I haven't pressed any buttons and the scanner doesn't work
Hello my friend. Be sure to read the description section. Yes, by default jamming is on channel one. My circuit doesn't work either
@@BabakStars bro, how do you get out of channel 1 and what are the pins for the buttons?
@@BabakStarsif your circuit doesn't work? Then why have you uploaded the video?
@styrishrodrigues Because I spent a lot of time on it, and it was the day I had to upload the video. But I suggest you watch the next episodes.
Can you make it bluetooth jammer with 3 nrf?
I made it once before. It was not working well. In general, the project with nrf24 is not interesting.
With 3 nrf ? I saw at instagram and youtube some one build it and works fine
And its can be add more than 3 nrf
OK. I will make a video about it and try to go over everything.
does this block 5G connections ?
In the second part and in the description part of the same video, it is said that this does not work.
Bro can you tell me which kind of battery do you use for on this 5v or 9v battery??
Hello. I used two lithium batteries that are connected to the VIN pin of Arduino. It means 7.4 volts. You can watch the next episodes of this project in the channel.
@@BabakStars hmm I can't wait for your video because I have to give this project tomorrow so can you tell me last thing if I used 3.3 v regulator for this project because as you know that nrf would have 1.6 till 3.6 v input voltage so if use regulator would it will be start and last again sorry for that I have issue I just used female to female wires for this project I don't connect any thing with board except only battery connection so if I do this would project work properly or still give me issue on that??
@@SaifKhan-gx9lf I wrote in the description section that this project does not work. But in the second part of this project, I connected the regulator, but I did not get any results.
@@BabakStars ohh no so this jammer will not resist any internet in a single mobile??so why it's is popular in a Arduino projects I got this from the Arduino main page
@SaifKhan-gx9lf Unfortunately, not. I made this at the request of another person. But look at this one.ua-cam.com/video/ewdN5eLwz7w/v-deo.html
Could you send me that Arduino main page?
would this work with the pcb antenna version too?
I explained in the description. It didn't even work with this module.
hello dear can this tool jam bluetooth. and if it jams bluetooth which channel should i choose
Sorry, this video was my first attempt to make jammer, but I got it from a fake online magazine. Better see the next episodes. Regarding Bluetooth, I don't know what channel it works on.
put it to the bin.. and buy portapack.
Yes, it will be very beautiful, but I said in the description of the video that this does not work
Hey man I hope u receive my comment I have question Can I use ESP-12E WeMos D1 WiFi UNO Based ESP8266 Development Board
Does it work?
I think if you watch the next part, It'll help you.
@BabakStars thanks for replying 😘
Please how to mke long distance woki toki?
lo conecte todo y no funciona, encien de la pantalla y dice que esta trabajando pero no bloquea nada, alguien tendra la solucion ? saludos!
Read the video caption. I will prepare another video about this.
@@BabakStars excelente muchas gracias!
which breadboard is this?
perforated board
@@BabakStarsWhat are the measurements?
Where can I buy them
Hello my friend. Amazon is one of the most suitable websites to buy them.
Hi sir I’m from the uk 🇬🇧 and I really enjoyed your video thanks for sharing it , I’m not a professional like yourself so I have a couple of questions if you could help
Hello my friend, thank you for your comment. Of course, if you have any questions, ask. I will answer if I know.
would this work with an arduino uno?
Yes. But as I said in the description, this project doesn't work.
Why my oled display is half working
What does half working mean?
Hello sir, sorry if I bothered you, I need your help. The screen that I have is different from the screen in your project. My screen works on the SH1106 library. I tried to replace the library and insert it into the code. I did not succeed. Please help me. How do I replace the SSD1306 library with the SH1106 library?🙏
Hello, you do not need to replace. If you can install the correct library, the display will work fine. Just search for SSD1306 and install the Adafruit SSD1306 library.
There are no special settings.
@@BabakStars Thank you, sir, for your reply, and sorry if I bothered you with my many questions. I will try what you said
Hello sir does it is really block the 2.4 ghz wifi
Unfortunately, no. Read the description of the video.
No talking, no sale
Watch other episodes
Names of device used ?
NRF24L01, Arduino NANO, OLED SSD1306. But first, read the description section.
Network jammer par ek video bana doo
I don't know if I can make it or not. 😅
@@BabakStars you can do it
Does the code work?
This project did not work at all. I wrote this in the description. Watch the next episodes
Circuit diagram please
github.com/BabakStars/A_fake_thing/blob/main/cd.jpg
@@BabakStars yes bro but please make a circuit diagram with the buttons I don’t know where to insert the buttons
@@BabakStars also does it scan through nearby WIFI connections and then you can select them to jam? By the way, what is the efficient range of the jammer? Of course I won’t use it for anything bad, just for testing
Defined in the program. Pins 2 and 3 are connected to the microswitch
Actually, I did not get a good result, but if you made the project and got a good result, please share with me.
Components used????
NRF24L01, arduino nano and SSD1306 OLED display
Hello sir, the screen is not working properly, please help🙏
that is weird. I don't know where the problem is
@@BabakStars At the top of the screen, lines appear in width, and at the bottom of the screen, numbers pass by at a speed that I cannot read🙏Screenwriting does not appear as it does in your video
Hello great video, please make some new arduino hacking tool for example Esp32 WiFi Hacking or Kali Linux Hacki g with python or RFID Card read/write or something else. Have a nice day.
Hello my friend, thank you for your useful comments. You also have a good day ❤️🙏