how would you do the compression test differently if you used the injector bores? and should i only have one injector out at a time or is it okay to have all injectors removed while testing one cylinder?
Same method. One injector at a time. you could also remove all injectors. And that would make the engine easier to crank because their is no compression happening in all other cylinders. But i prefer to test it while the other injectors are still installed because that would mimick actually engine load while you are testing one cylinder.
@@MrDIYer okay thanks. i have the injectors out because i just got them rebuilt. i was having hard starts and blowing smoke. i hope the clean injectors solve this! figured i should check the compression while i'm here.
Hahahaha eh di wag. Di ka kawalan sa channel ko. Wala namang nag pupumilit sayo. Lol eto lang maipayo ko sayo, subukan mo kasing mag aral baka sakali maintinidihan mo. Pwede rin balik ka grade 1 hahahaha. Ang dami ko ng na encounter na pinoy na tulad mo na feeling entitled. Tandaan mo ang youtube di para sa pinoy lang at lalong lalo nat di para sayo lng. Di ko ginawa yang video na yan para lang sayo. Kaya kung di mo nagustuhan wala akong paki lol. Eto pa di ko magets sa mga tulad mo, malamang nanood ka dahil gusto mo matuto at baka maka tulong sa problema sa makina mo, pero ugali mo ganyan pa. Lol libre lang to, pero kung maka comment ka akala mo kung sino ka nag babayad wala ka namang ambag. Lol Tandaan mo kung di mo trip na papanood o nadidinig mo maari ka mag hanap ng iba at di mo na kailangan mag ganyan pa dahil wala naman kita inano, Pero dahil ang hina ng kokote mo di mo alam yan hahahaha.
![Lp. Последняя Реальность #107 РОДНОЙ ДОМ [Финал] • Майнкрафт](http://i.ytimg.com/vi/IK3QKzKUlHM/mqdefault.jpg)
Very helpful video sir! Hope to see more videos!
Thanks a lot sir, thanks to you I found the problem on my Nissan Vanette Cargo 2.3D
Thank you !
Nice
Very informative😉 looking forward for more videos😉💕 God bless🙏🏼
Ppop
OK sir thanks
why would you stop cranking while the gauge is still going up?
what kind of oil did you put into the glow plugs? thanks for your videos!
Sae 40 engine oil
Did you heat it before it start,????
Sir rf mazda diesel usok at talsik sa deepstick for overhaul na po ba un?
Ano po pinalitan nyo nung inoverhaul nyo 4d56?
nice master.can you show me were is the location of pcv valve of 4d56 engine and 2l engine thank you
No pcv valve on 4d56
@@MrDIYer thank you sir
how would you do the compression test differently if you used the injector bores? and should i only have one injector out at a time or is it okay to have all injectors removed while testing one cylinder?
Same method. One injector at a time. you could also remove all injectors. And that would make the engine easier to crank because their is no compression happening in all other cylinders. But i prefer to test it while the other injectors are still installed because that would mimick actually engine load while you are testing one cylinder.
@@MrDIYer okay thanks. i have the injectors out because i just got them rebuilt. i was having hard starts and blowing smoke. i hope the clean injectors solve this! figured i should check the compression while i'm here.
Sir, is this applicable to the 4m41 engine using the same device?
Yes sir
@@MrDIYer got it sir. Will purchase this device and try it out. Thanks sir
what is a wet testing and dry test
I think, In wet test splashing a little amount of engine oil to the combustion chamber (filling space for wear of liner & piston ring).
to check whether the whether it's a bad valve, head gasket, or worn piston rings
May usok na puti pero d nagbabawas ng langis 4jb1
head gasket leak or may bengkong sa cylinder head
testing should be done on COLD engine only
Tanung ko lng po bakit yung sasakyan ko po na l300 fb bagong overoll nman po pero yung tunog nya maingay parin po anu sira po nun
yan di ko masagot sir. tanong nyo po sa nag overhaul. maraming sanhi. pwede maling tune up. pwede rod knock,piston slap. engine knock.
@@MrDIYer lumalagatak po tunong nya tapos hirap humatk sya
@@MrDIYerlast year 2019 ng december lang po inoveroll po sasakyan ko eh
baka piston rings lang pinalitan
@@MrDIYer lahat sir pinalitan bago lahat sir ako kasi bumili ng pyesa nun
Subcribe sana ako kaya lang di ako nakka intindi ng english
Hahahaha eh di wag. Di ka kawalan sa channel ko. Wala namang nag pupumilit sayo. Lol eto lang maipayo ko sayo, subukan mo kasing mag aral baka sakali maintinidihan mo. Pwede rin balik ka grade 1 hahahaha. Ang dami ko ng na encounter na pinoy na tulad mo na feeling entitled. Tandaan mo ang youtube di para sa pinoy lang at lalong lalo nat di para sayo lng. Di ko ginawa yang video na yan para lang sayo. Kaya kung di mo nagustuhan wala akong paki lol.
Eto pa di ko magets sa mga tulad mo, malamang nanood ka dahil gusto mo matuto at baka maka tulong sa problema sa makina mo, pero ugali mo ganyan pa. Lol libre lang to, pero kung maka comment ka akala mo kung sino ka nag babayad wala ka namang ambag. Lol
Tandaan mo kung di mo trip na papanood o nadidinig mo maari ka mag hanap ng iba at di mo na kailangan mag ganyan pa dahil wala naman kita inano, Pero dahil ang hina ng kokote mo di mo alam yan hahahaha.
Bo-plaks ka kasi. Subukan mo mag aral para next time maisipan mo mag comment di kahiyahiya. 🤣