Ford Excursion F250 F350 Superduty 1998-2004 Thrust Washer Kit Install
Вставка
- Опубліковано 8 січ 2020
- Get Your Parts Here
Kit for both sides
venturestruckparts.com/produc...
Kit for one side.
venturestruckparts.com/produc...
Ventures Truck Parts shows how to install Fords thrust washers for the Dana 50 or Dana 60 front axle for F250, F350, and excursions 1998-2004
Ventures Truck Parts
801-621-0091
Ventures@readytek.net - Авто та транспорт
Thanks for this.. Mine was built by a "Pro" Shop that did not install the inner Thrust washer that run between the Spline shaft and the Unit Bearing.. This allowed the Shaft to beat the needle bearings to death . after 10,000 miles i am now rebuilding the entire Dana 60 because of this rookie mistake.
Yes, this woudl be even more helpful if you showed this detail with the Vacuum Dust Seal in Place on the Spline shaft just to make it 10000% Clear.
Thank you. Again.
same here!
Excellent work; there are videos that show the thrust washer on the outside of the uni bearing; great you showed it ON THE INSIDE!
Its been a while since I have done one of these hub replacements. I'm digging into one right now and the inside thrust washer was just behind the stack of 3 thrust washers. I consulted Mitchell Pro Demand with no luck, then UA-cam. 3 videos in a row had them wrong. Thank you for clearly demonstrating the proper method!
Great, no bull just what I needed. Thank u much.
Had to search a bit to find this, most straightforward, important secretions. Thx for taking the time to help out us anal mechanics that have to make sure we've got it right ✅️
Just for others interpretation, this might appear weird, but generally the axle is installed so you're putting that thrust washer inside of the knuckle onto the shaft then installing the bearing.
Thanks was stuck. Until I seen your video. Had a friend started working on my truck. But I had to put it back together. Was so stuck on why I couldn’t get the snap ring on. Thanks again.
Great! Iv watched other videos of changing the axle and they didn't go into detail about the washers. Thank you! Now I just have to find them. Was hoping to get at auto store, but no.
Great! Exactly what I was looking for! I kept track of the outer thrust washers (directly under the snap ring) but the inner thrust washer fell out when I removed the hub assembly and I didn’t know which was. Thank you very much!!!
Good Stuff, Great Tips👍🏿😀 2016 F250 XLT 6.2L 4W 4D (Stock)
Thanks good video ✌️
Thanks nice job.
THANY YOU VERY MUCH
It should be noted that the vacuum seal which normally surrounds the base of the stub axle has been left off for ease displaying the thrust washer placement. If one puts the hub back together with out the back seal it will not function properly. Question. Is grease recommended for either the inner thrust washer or the outer thrust washer set?
Thanks; though I wish you'd have had the Vacuum Seal on the axle as well so we can see what it looks like in total.
Ditto . !
Every time I work on a truck they are jumbled all around I am so confused by the mess. I swear I can't remember how it goes again.
Take pictures or video, it works for me
Simple and informative video, love the content you guys have been putting out. If I am converting my 99-04 to 35 spline outer stub shafts, what thrust washer kit should I get?
Should these be lightly lubed?
What would cause there to be a gap between the snap ring and thrust washers? I’ve replaced ball joints, hub bearing assemblies, all the seals and thrust washers but there is a significant gap between the snap ring a thrust washers. Any advice is greatly appreciated.
Call us and we will be happy to talk. 1800-464-1713
Hey. Do you guys sell the whole hub bearing too??
Yes we do have them available. Check out our website or give us a call. 801-621-0091
So 06 f350 doesn't need thrust washers?
No, 2006 will not have thrust washers.