Hey Peter, Glad you liked the video. These are good requests and when I get a moment spare I may make a follow up video soon addressing these things. Just to be sure that I understand, what exactly are you meaning by "laying out marks"?
Thanks for the instruction! I went looking for that bender - it was $900, and has been discontinued. I looked at your site - no tools listed. Is there a bender worth buying in the sub $100 range I can use to bend 1/2" stainless seamless .049 wall for an older skid steer? The lines are no longer available, and I would like to make my own. Thanks!
Hi I bought a Rigged 1/2 inch tube bender before I ran across your video, thank you for teaching at a pace that I can absorb, I am Bending 1/2 inch stainless for a car build ,my bender it pops in and out was wondering if you could go thru it how you teach ,thank you ahead and greatly appreciate your work
Hi, Micheal! Thanks for the kind words and glad you liked the video. I have not personally used the Rigid brand bender, but we have recently sourced a few of them and they seem like a good quality tool. Can you explain the issue you are having a little more? What exactly is popping in and out?
Nice video 👍 I have a question. If the nuts were against each other. How do I know how much to add to the measured value between the matrices. So that it is just on both sides accurate in the nuts. Is there a table for how much to add on a given size. Thx
Thanks for the question Millan, This information can be found on the spec sheet for the fittings. Here is the spec sheet for the Superlok i-Fitting uploads-ssl.webflow.com/614a0a8332b6ab3696001910/639caec79f35af95e9dd6182_Superlok-i-Fitting-Full-Catalog.pdf It may be different if you are using a different brand of fitting.
We need the "R" part explained i understand its for reverse bending just don't know what a reverse bend is and how does a 45 work with 90 or a reverse cheers
Hey great video , that’s a nice bender with very nice usable graduations on it , iv done a little pipe / tube ? bending before on hydraulic systems at work with reasonable success but the processes I used to achieve the bends were a lot more difficult due largely to having no graduations on the bender. Anyway great video nicely presented and iv learned some valuable tips from it thanks man Ps iv not watched all your videos maybe you already have one but if not a video on how tight to make them would be a good one to do 😄
Hey Peter, Glad you liked the video! We do have a video about tube fitting installation as well. You can check it out here → ua-cam.com/video/HwmkNiTNGeU/v-deo.html We are always looking for more video ideas though, so be sure and suggest any other ideas also. We love informing people about how these products work and how to use them safely.
Some vids say the L and R are for which side of the bend you are bending from, Left or Right. I'm trying to figure that part out so not a criticism, just want to know
There is an element of truth in the "left and Right" idea. However, I feel it is confusing to say left and right. These are subjective terms that would be impacted by your position relative to the work. If we consider the origin of your measure to be the "Right" and the tail that you measure towards the "Left" then when you have the "right" side clipped into the latch you are bending toward the "left". This would use the "L" mark to make a 90° bend. If there is not space for your bender to bend in this direction, you will have to Reverse the direction of the bender now bending from the left to the Right. This would then use the "R" mark to make the same 90° bend at the correct location. For this reason, I would say that "L" is for L bend and "R" is for reversed bend.
You are correct. This is a viable method to measure center to center if the fittings are in the same plane and you are making a straight line between them (as in the video). However, once a few more dimensions are needed, it gets a bit more muddled. At that point you can either measure to the center or start doing some math to subtract half of your fittings diameter.
1" tubing can be bent using a couple of different options of tool. They do make large scale lever style benders for 1" tubing, but it would be easier to work with something like an Imperial 270 gear type bender. The important thing to keep in mind if you are bending any size of tubing for use with tube fittings, is make sure you are using a quality bender that does not mar the surface of the tubing. At higher pressures any imperfections can become a failure point.
i build small jet engines...its just a hobby,,i have great difficulty in making up the vaporising tubes for the combustion chamber. . its 10mm tubing bent to 180 degrees what they call walking sticks ..when i make one it nearly allways gets collapsed and need to beat it to gain some sort of result..... each engine has 10 of these walking sticks ,, i would dearly like to purchase a device to solve my problem.... regards laurence
Tube cutters are very convenient. However, they tend to leave a sharp ridge inside the end of the tubing. This narrowing just at the very tip can cause turbulence, pressure drop and flow restriction in the line. While this issue is easily fixed with a de-burring tool on soft metals like copper, stainless is quite hard which makes it difficult to remove the burr. The saw teeth leave a burr also, but the are quite a bit smaller and can be easily handled with a hand tool. If I was to be working on tubing in the shop all day, my preferred cutting tool would be a band saw. But I understand that band saws are not viable for field use.
The center of the bend is not the crucial measurement. Since tubing runs are measured on the center line, the L mark lines up with the center of the tubing after the bend. Basically, If you needed just a 90° bend at 6", and you measure to 6" and line up to the L, The center of the tubing leg will be at exactly 6".
The one in this video is an Imperial Roto-lok Tubing Bender. But any reputable brand of instrumentation tubing bender should have the necessary features for proper bending.
This has been the best instruction I have seen so far. Just wish you would have shown laying out marks and using the R
Hey Peter,
Glad you liked the video. These are good requests and when I get a moment spare I may make a follow up video soon addressing these things.
Just to be sure that I understand, what exactly are you meaning by "laying out marks"?
I would like to know what the diameter of the tube is?
Hey thanks . I'm always trying to learn a new way of bending tubing!
I have to build up some oil lines to feed a turbo!
Perfect!!! Showed me everything i needed for a basic bend. Thank you
This videos are really helpful, wish to see more soon!
Thanks! we are glad you like them. We are always open to suggestions for topics. Is there a topic you would like to see covered?
Good Job on the presentation and great explanation!
I'm impressed with the stainless tube bender. Could I get a quote for a 19mm. diam. stainless steel tube bender.
great demostration.
Does anyone use setback advance and gain formulas and layout tubing properly? I can't seem to find any videos showing the actual way to bend tubing...
Thanks for the instruction! I went looking for that bender - it was $900, and has been discontinued. I looked at your site - no tools listed. Is there a bender worth buying in the sub $100 range I can use to bend 1/2" stainless seamless .049 wall for an older skid steer? The lines are no longer available, and I would like to make my own. Thanks!
Very informative video. Thanks!
Nice job! Very informative
Great work
Wow great video!!! I feel like a pro now.
Thank you. Great to hear!
Thanks. Very helpful to watch your video.
Nice presentation guys..from 🇮🇳
Very good content. Thank you!!
Glad you liked it!
You can also measure from the outside edges and will give you a more accurate measurement.
Great info. very complete. Thank You.
Hi I bought a Rigged 1/2 inch tube bender before I ran across your video, thank you for teaching at a pace that I can absorb, I am Bending 1/2 inch stainless for a car build ,my bender it pops in and out was wondering if you could go thru it how you teach ,thank you ahead and greatly appreciate your work
Hi, Micheal! Thanks for the kind words and glad you liked the video.
I have not personally used the Rigid brand bender, but we have recently sourced a few of them and they seem like a good quality tool.
Can you explain the issue you are having a little more? What exactly is popping in and out?
That looks like a brake line bender. Do you have a more advanced class to help with determining angles ?
Measure from OD on one fitting to ID on the other fitting to get center to center measurement.
Nice video 👍 I have a question. If the nuts were against each other. How do I know how much to add to the measured value between the matrices. So that it is just on both sides accurate in the nuts. Is there a table for how much to add on a given size. Thx
Thanks for the question Millan,
This information can be found on the spec sheet for the fittings. Here is the spec sheet for the Superlok i-Fitting
uploads-ssl.webflow.com/614a0a8332b6ab3696001910/639caec79f35af95e9dd6182_Superlok-i-Fitting-Full-Catalog.pdf
It may be different if you are using a different brand of fitting.
Thanks for the video
Our pleasure!
Excelente, recomendaciones para el ajuste de racort.
We need the "R" part explained i understand its for reverse bending just don't know what a reverse bend is and how does a 45 work with 90 or a reverse cheers
Hey great video , that’s a nice bender with very nice usable graduations on it , iv done a little pipe / tube ? bending before on hydraulic systems at work with reasonable success but the processes I used to achieve the bends were a lot more difficult due largely to having no graduations on the bender. Anyway great video nicely presented and iv learned some valuable tips from it thanks man
Ps iv not watched all your videos maybe you already have one but if not a video on how tight to make them would be a good one to do 😄
Hey Peter,
Glad you liked the video! We do have a video about tube fitting installation as well. You can check it out here → ua-cam.com/video/HwmkNiTNGeU/v-deo.html
We are always looking for more video ideas though, so be sure and suggest any other ideas also. We love informing people about how these products work and how to use them safely.
Some vids say the L and R are for which side of the bend you are bending from, Left or Right. I'm trying to figure that part out so not a criticism, just want to know
There is an element of truth in the "left and Right" idea. However, I feel it is confusing to say left and right. These are subjective terms that would be impacted by your position relative to the work.
If we consider the origin of your measure to be the "Right" and the tail that you measure towards the "Left" then when you have the "right" side clipped into the latch you are bending toward the "left". This would use the "L" mark to make a 90° bend. If there is not space for your bender to bend in this direction, you will have to Reverse the direction of the bender now bending from the left to the Right. This would then use the "R" mark to make the same 90° bend at the correct location.
For this reason, I would say that "L" is for L bend and "R" is for reversed bend.
measkure from edge to edge on the same side of the circle to get center
You are correct. This is a viable method to measure center to center if the fittings are in the same plane and you are making a straight line between them (as in the video). However, once a few more dimensions are needed, it gets a bit more muddled. At that point you can either measure to the center or start doing some math to subtract half of your fittings diameter.
Thank you 😄
🎉you are good man
What tool do you use to bending a 1" tubbing ?
1" tubing can be bent using a couple of different options of tool. They do make large scale lever style benders for 1" tubing, but it would be easier to work with something like an Imperial 270 gear type bender. The important thing to keep in mind if you are bending any size of tubing for use with tube fittings, is make sure you are using a quality bender that does not mar the surface of the tubing. At higher pressures any imperfections can become a failure point.
thank you
No 7/16ths deduction?
i build small jet engines...its just a hobby,,i have great difficulty in making up the vaporising tubes for the combustion chamber. . its 10mm tubing bent to 180 degrees what they call walking sticks ..when i make one it nearly allways gets collapsed and need to beat it to gain some sort of result..... each engine has 10 of these walking sticks ,, i would dearly like to purchase a device to solve my problem.... regards laurence
Thanks
Too much applied points..
But why you didn't use the tube cutter which is more convenient rather than hand saw .
Good luck and again thanks
Tube cutters are very convenient. However, they tend to leave a sharp ridge inside the end of the tubing. This narrowing just at the very tip can cause turbulence, pressure drop and flow restriction in the line. While this issue is easily fixed with a de-burring tool on soft metals like copper, stainless is quite hard which makes it difficult to remove the burr. The saw teeth leave a burr also, but the are quite a bit smaller and can be easily handled with a hand tool. If I was to be working on tubing in the shop all day, my preferred cutting tool would be a band saw. But I understand that band saws are not viable for field use.
Büktüğün boru kaç mm dış çapı
9,5 mm'ye yakın
Why the L? It didn’t put your mark in the center of the bend. Is that the goal?
The center of the bend is not the crucial measurement. Since tubing runs are measured on the center line, the L mark lines up with the center of the tubing after the bend. Basically, If you needed just a 90° bend at 6", and you measure to 6" and line up to the L, The center of the tubing leg will be at exactly 6".
@@SuperlokTV Roger that. It’s been a growing pain to learn this. Thank you for your input and patience.
If anyone in the oilpatch used a hacksaw to cut their tube they would run them off the job.
what is the name of the tool?
The one in this video is an Imperial Roto-lok Tubing Bender. But any reputable brand of instrumentation tubing bender should have the necessary features for proper bending.