@KinoYves Do not eat and touch because pork is unclean Leviticus 11:7 - 8 God hates pork eater and eating pork is wrong Isiah 65:12 & 65:17 Obviously the person God of bible hates will go to eternal hell fire
Nice work! As an owner of a thumper (single cylinder bike) that has a semi automatic transmission similar to the Honda Cub unit shown in the video, it is a pleasure to see your craftsmanship.
I can't wait to see it work. U engines rob power but are well balanced engines. The primary and secondary harmonics are nearly cancelled. It should have minimal vibration and be capable of reaching higher rpms than the stock engines..
@@vanai3663 làm vì đam mê là chính nên hiếm thấy quay mặt trong video. Mình nghĩ kênh cũng hướng tới người xem quốc tế nhiều hơn trong nước vì tựa đề video toàn tiếng Anh thôi, mà việc review bằng TA nó lại không dễ
không biết nói sao về đam mê sáng tạo của a ấy luôn ă trời. thiết bị đầu tư cùng bộ óc sáng tạo thiên tài máy móc rất tuyệt. chúc a sức khỏe để ra những siêu phẩm mới nhé
I see 3 potential mistakes, One is when he milled the head flat, he should've shaved the head in a continuous motion, not change from an X pass to a Y axis pass, it have to do with the milling head alignment that is not always perfect. Another potential mistake is using one carb for both heads, if he intend to offset the timing like he seems to it could end with an uneven mixture between both sides. A third one will be if there's no oiling to one of the cylinder heads. Nice build though I hope it works at the end.
Can't wait for the results, you are awesome 👏🏻 respect from Indonesia 🙏🏻 I just remembered about ARIEL SQUARE FOUR engine, same with what u've made, but it has 4 piston, i hope that one day, u'll make it 😊
Honda made oval pistons to fit more valves without increasing the bore in a 4 cylinder engine. The NR500 was a V4, with 8 valves per piston, and with two connecting rods per piston. I bet you couldn't… (the street version was the NR750, which also had two rods per piston & oval bores, but elliptical pistons instead of straight sides)
would help if you knew what you were on about in the first place, it was built because more than 4 cylinders was banned in racing and the only way Honda could hope to compete with the 2 strokes was building a V8, as that wasn't allowed they came up with the closest thing to a V8 the rules allowed, the whole concept was a massively expensive failure as well and if Honda failed how the hell is a fella in a glorified shed supposed to make one?
@@andyc750 I don't know, but he might. He did just stick two crank cases together. And yes, that was to get a v8 down to the mandated 4. The reason why Honda wanted 8 was more valves. Otherwise they would have used 4 round pistons.
wawoooo quelle savoir faire je vous suis depuis une Anne et j'adore votre savoir faire qui est très très très formidable j'animerai venir me former chez vous et je voudrai savoir si c'est possible ?
I need a 250cc 2 stroke scooter engine long case, bottom mounted like qmb gy6 engine... i think alot of people would love to see something like this built!
In our country innovation is not allowed and encouraged and they do not grant patents without giving money to officials. If you go out on the street, it will be confiscated and fined. He only made it out of passion but was not allowed to circulate it. If you have the opportunity to come to our homeland, Vietnam, please visit this engineer. Nice greetings from Vietnam
Recuerdo ver uno de tus videos pasados con un motor en V a 90* si no recuerdo mal. Sueles utilizarlos o solo para los vídeos? Lo pregunto por su fiabilidad. Podrías replicar el motor de la BMW R80 de un motor bicilindirico plano unidos ambas bielas al mismo eje de cigüeñal? O con un supercargador central. Solo son ideas. Un saludos desde Canarias
Wow! A new video from Le Dan! It's always a pleasure. Good morning, and respect, from Redmond, Washington. 👍👍👍
Haha im not too far away. Portland sucks.
@KinoYves Do not eat and touch because pork is unclean
Leviticus 11:7 - 8
God hates pork eater and eating pork is wrong
Isiah 65:12 & 65:17
Obviously the person God of bible hates will go to eternal hell fire
Nice work! As an owner of a thumper (single cylinder bike) that has a semi automatic transmission similar to the Honda Cub unit shown in the video, it is a pleasure to see your craftsmanship.
However, this would have been much harder with a liquid cooled engine.
Guy makes my random engine tinker thoughts from years ago a reality, thank you so much.
Haha yep , loads of us master genius engineers solving every conceivable mechanical problems while our heads rests softly on the pillow! 😴
Someone give this man bigger mill bits and a year supply of coolant xD
Sorprendente su diseño y mecanización y tú pensando en chulerias, seguro eres latino...por eso están como están .
Never gets old watching this guy.
I can only think these things;
You make it.
I have been thinking of a U-4 engine for such a long time. You made a U-2 engine. Lovely.
I can't wait to see it work. U engines rob power but are well balanced engines. The primary and secondary harmonics are nearly cancelled. It should have minimal vibration and be capable of reaching higher rpms than the stock engines..
là 1 thợ sữa xe nên mình chỉ nói là đỉnh, ai là thợ sữa xe thì sẻ hiểu nó khó và rất nhiều cái cần xử lí
Đúng rồi bạn thật sự kiêm trì
Luar biasa sangat kagum dengan ilmu yang di miliki 👍👍👍
Love watching your videos, they never fail to impress 👍 keep up the good work 👍
We saw another great piece of engineering. Congratulations for you.
you re a artist from steel, thanks for sharing
Wonderful engine build!!!!
Quedo expectante de la continuación de este vídeo. Que Excelente mecanizador es Usd. Sus videos son geniales.
Amazing, just wow. Very talented.
great idea, lets hear all the different sounds compared!
you alwals make me surprised sir. good job! good work!🔥
I just subscribed! Your channel is awesome! Switzerland 🇨🇭
รอดูตอนต่อไปครับ Fc.จากประเทศไทย
All I can say is WOW, you're so talented dude.always watching your videos sir I'm from Philippines
tandem twin, very cool and your best so far I think, curious to see how you go about the rest of the build now
Cool build,, 👍😎👍
Deseando ver el siguiente capitulo, le Dan eres un Crash un autentico maestro, 👏👏👏👏👏👏👏👏👏un genio, un saludo
Quá là đỉnh luôn a , ko từ nào để tả nổi 👏😁
😍😄 wow - something new - I love it ! That Honda engine is way more complicated than the Yamahas you normally use
That’s absolutely not a Honda engine, it’s a HONGDA(Chinese-illegal copy engine)
@@thanhquangtrinh9640 i meant - a Honda based engine - it's still made like a Honda
LÊ DÂN anh là ai sao mà làm cái gì củng quá dể . Làm vì đam mê sao .món nào cung làm được . Quá đỉnh
Đung vậy bạn sao anh ấy ít quay mặt và reviu nhi
@@vanai3663 làm vì đam mê là chính nên hiếm thấy quay mặt trong video. Mình nghĩ kênh cũng hướng tới người xem quốc tế nhiều hơn trong nước vì tựa đề video toàn tiếng Anh thôi, mà việc review bằng TA nó lại không dễ
không biết nói sao về đam mê sáng tạo của a ấy luôn ă trời.
thiết bị đầu tư cùng bộ óc sáng tạo thiên tài máy móc rất tuyệt.
chúc a sức khỏe để ra những siêu phẩm mới nhé
Mr.Problem Solver...
Well done...!!!! 👍🏻👍🏻👍🏻
Không có gì làm khó em trai này hết. Chúc em nhiều ý tưởng mới
im a machinist in arizona, someday i hope to have my own tools to do stuff like this
Veramente un lavoro eccezionale, complimenti 👍🏻
Wow, looking forward to the next video on this
I see 3 potential mistakes, One is when he milled the head flat, he should've shaved the head in a continuous motion, not change from an X pass to a Y axis pass, it have to do with the milling head alignment that is not always perfect. Another potential mistake is using one carb for both heads, if he intend to offset the timing like he seems to it could end with an uneven mixture between both sides. A third one will be if there's no oiling to one of the cylinder heads. Nice build though I hope it works at the end.
La je me demande pourquoi j'ai commenté en anglais. Super travail LeDan. 👍
Luar biasa mantap ide dan eksekusi jadi nya!👍👍👍👍👍
you do amazing work
Muito bom, excelente trabalho. Estou querendo vê-lo em funcionamento.
Fantastic!
I can't wait for Le Dan to make a straight 6 cylinder.
❤❤❤the best chanel
Wow! ❤you - great engineer)
Cant wait for test drive 🥰
This such a Beautiful craft. 👍
Excellent job
Thank you for supporting $❤️❤️❤️
Mọi chi tiết, Anh! làm rất tỷ mỉ ,phải nói là rất chất lượng thì 👍
cool. what i'd love to see is a follow up of any of the previous engines - did they last? do they run well? do they run at all?
Wow cái động cơ lạ nhất mà anh từng chế tạo ra Anh Dan 😂😂🤘🤘
I'd still love to see you Make a inline 5 engine with volvo firing pattern
Mọi chi tiết, Anh! làm rất tỷ mỉ ,phải nói là rất chất lượng .
Yep ! You are the boss ! Congratulations very good job ! @+ Alex. Nail Patella
Awesome...
Amazing ❤
Inspiration ❤❤❤
que locura amigo. impresionante
Nice. Now all that's needed to make it run is everything else. Should be a walk in the park.
Wao kren banget modifnya mantap
Menunggu video selanjutnya 😮😮😮
Amazing.
Can't wait for the results, you are awesome 👏🏻 respect from Indonesia 🙏🏻
I just remembered about ARIEL SQUARE FOUR engine, same with what u've made, but it has 4 piston, i hope that one day, u'll make it 😊
Mirip konsep mesinnya mas Yusuf Psycho engine yang pake mesin Honda Tiger
@@rifalyp2170 iy bang, pioneer pertama buatnya 🙏🏻☺️
Wow amazing idea next vidio
Will require extra oil cooling for rear cylinder as it gets less air cooling than the front. Awesome work as always 😊
Honda made oval pistons to fit more valves without increasing the bore in a 4 cylinder engine. The NR500 was a V4, with 8 valves per piston, and with two connecting rods per piston.
I bet you couldn't…
(the street version was the NR750, which also had two rods per piston & oval bores, but elliptical pistons instead of straight sides)
And this is relevant to this video because?……..
@@raymondsanderson3768 lol
You shouldn't have a keyboard.
would help if you knew what you were on about in the first place, it was built because more than 4 cylinders was banned in racing and the only way Honda could hope to compete with the 2 strokes was building a V8, as that wasn't allowed they came up with the closest thing to a V8 the rules allowed, the whole concept was a massively expensive failure as well and if Honda failed how the hell is a fella in a glorified shed supposed to make one?
@@andyc750 I don't know, but he might.
He did just stick two crank cases together.
And yes, that was to get a v8 down to the mandated 4. The reason why Honda wanted 8 was more valves. Otherwise they would have used 4 round pistons.
I like you chanel so inspiration for my
Le dan..are u real human?? Or u from another planet 😂😂..u are too genius dude..
Good job bro
ini yg aku tunggu²😊
Фантастика которая стала реальностью 🤝
Keren cseries selalu di hati
Mr.Le Dan....are you from this planet 👌👍👏❤
Every time next level
wawoooo quelle savoir faire je vous suis depuis une Anne et j'adore votre savoir faire qui est très très très formidable
j'animerai venir me former chez vous et je voudrai savoir si c'est possible ?
I need a 250cc 2 stroke scooter engine long case, bottom mounted like qmb gy6 engine... i think alot of people would love to see something like this built!
When I see a flycutter like that all I can say is
gaht DAMN bwa!....
HE THICK bwa!
It’d be cool if you made a inline 5
Nice👍
Love from thailand
New invention good!
Parabéns sou seu fã Dedé motos de Quixadá no Ceará BRASIL
как всегда друг достойно уважения твоя работа!
Le Dan is the Mad Scientist of engines
You can be amazed by what you can accomplished with a standard 220v arc welder.
Impressionante
Đỉnh quá anh ơi._____ người việt nam 🇻🇳🇻🇳🇻🇳
🇮🇳 love from India 🇮🇳 .. my brother made a similar engine using HONDA engines and cnc machine...and attached it to a agriculture machine
How it's work.what is?
@@nawecreation334 petrol based engine
In our country innovation is not allowed and encouraged and they do not grant patents without giving money to officials. If you go out on the street, it will be confiscated and fined. He only made it out of passion but was not allowed to circulate it. If you have the opportunity to come to our homeland, Vietnam, please visit this engineer. Nice greetings from Vietnam
Tuyệt vời anh ơi, sáng kiến tuyệt vời
Nice vid
Recuerdo ver uno de tus videos pasados con un motor en V a 90* si no recuerdo mal. Sueles utilizarlos o solo para los vídeos? Lo pregunto por su fiabilidad. Podrías replicar el motor de la BMW R80 de un motor bicilindirico plano unidos ambas bielas al mismo eje de cigüeñal? O con un supercargador central. Solo son ideas. Un saludos desde Canarias
Em 120 graus,ele soará como um V6.
Bom trabalho.
Meu nome e Franklin e moro no Brasil,na cidade de Jandira.
I would love to see how he's going to run this engine with the exhaust phone to the intake of the other head
Have wondered about you setting up a foundry to make these stranger parts?
I was waiting for new video
😮😮!! A New video from le Dan, awesome. Good afternoon and respect from sahabatbonsai88 . Jakarta
wow.. this way you can make a 2 stroke v4 engine with 2 crankshafts 👍
WoW... its great to see your videos Le Dan. Can you help me convert a KTM Duke 390 Motorbike engine to a Twin cylinder engine?
Thanks.
ông anh tầm cỡ vũ trụ luôn ròi vậy mà cũng chế được😮
Try making a 3 or 4 cylinder two-stroke Kawasaki Ninja engine once, it will definitely attract lots of spectators
I'll be waiting for the test fire...👍
we want part 2 soon
Cool build! But it's called an inline engine when the cylinders are on a row.
Ni orang kreatifnya beda 👍
Le Dan is the reincanation of Tesla. Let's all pray that he gets a billion dollar grant to start a motor company.
Ive always wished I had the abilities and equipment to do this with two Ford 4.9L Inline 6's.