That actually looks a lot faster then a c clamp press.I might pick this tool up the can be a bear to get out and that’s with a good clamp did you use to install if so how did that go ?
This will definitely be my go to when removing u-joints from now on. No it's not an installer but installing is the easy part. I used a hammer to taps the cups in on this particular job. Placing in vise or c-clamp works great also.
Good video these will not work on some of the GM driveshaft because it’s too much of a slant but when you do get a chance to use one of these over a ball joint press it’s much more efficient I think I have like 23 U joint puller resize a restyle
Nope it’s just the way those older GM driveshaft for me well at least the aluminum ones I did a 1994 GMC 1500 van and I ended up using a ball joint press to pop out do U join I think they’re steel you joints might be different but I don’t remember
OK I just remembered I used the u joint puller tool to do the Front u joint on the propeller shaft for a 2003 Chevy trailblazer so on the trailblazer you could use the special puller tool
Wish mine came out that easy. I have the same press but no success it was just twisting the shaft joint. Ended up using a ball joint press to get them out.
the ears on the yokes and driveshaft are flat and have an angle to them while the tips of that tool have curves. great for pushing on a ujoint but not yoke or shaft ears, thats the only problem i see with that tool, and the width is not adjustable. better than beating it with a sledge though by far.
I have the same Tiger tool and Milwaukee impact, good video.
I use the large one of semi and machine ujoints and its easier than a regular c clamp style tool. Rock on bro🤟🤟
That actually looks a lot faster then a c clamp press.I might pick this tool up the can be a bear to get out and that’s with a good clamp did you use to install if so how did that go ?
This will definitely be my go to when removing u-joints from now on. No it's not an installer but installing is the easy part. I used a hammer to taps the cups in on this particular job. Placing in vise or c-clamp works great also.
Simple tool but effective
Good video these will not work on some of the GM driveshaft because it’s too much of a slant but when you do get a chance to use one of these over a ball joint press it’s much more efficient I think I have like 23 U joint puller resize a restyle
Good to know. Wonder if a piece of shim stock can be wedged in the outer end of yoke to get it straight?
Nope it’s just the way those older GM driveshaft for me well at least the aluminum ones I did a 1994 GMC 1500 van and I ended up using a ball joint press to pop out do U join I think they’re steel you joints might be different but I don’t remember
OK I just remembered I used the u joint puller tool to do the Front u joint on the propeller shaft for a 2003 Chevy trailblazer so on the trailblazer you could use the special puller tool
2007 Cummins 4-4 Front drive Shaft what size do I buy.
Pretty sure you need the lisle 42900 medium one. I think the large will be too big. Check the Q&A on amazon and I bet it will say
Wish mine came out that easy. I have the same press but no success it was just twisting the shaft joint.
Ended up using a ball joint press to get them out.
I think using the torch was the trick on these or else they may have not come out.
@@raincitywrench117 So many people forget to use a little heat and end up bending the ears.
I made that mistake years back 😪@@oby-1607
the ears on the yokes and driveshaft are flat and have an angle to them while the tips of that tool have curves. great for pushing on a ujoint but not yoke or shaft ears, thats the only problem i see with that tool, and the width is not adjustable. better than beating it with a sledge though by far.
Yea. The couple times I used, it worked pretty good.
The 890 Won't fit on a chevy 2500 truck driveshaft with aluminum yokes.
Oh yea, good catch. Those have the thick yoke aluminum driveshafts. Have to use a u-joint or ball joint press.
I could’ve used this today, F I’m pissed😅
Had a real stubborn u-joint one day so decided to pick up the tool & said never again 😎
I have a set of these and I’m mostly disappointed with them
Why is that?