You just helped me right now with this step by steps instructions I was just looking for something like this for my rc car you are the best man keep the great work up may God bless you.👍👍👍😍😍😍😎😎😎
The racers edge capacitor is like a backup power supply. All it takes is a tiny voltage glitch and the receiver will loose binding with the transmitter and will need to rebind to the transmitter and that can take a couple seconds while the car is going 100mph.
Great Video, I own just about every Arrma RTR besides the Limitless and I want one even though I have the Felony. I think I may just try the body and wing kit with the felony and see how it looks with those bigger tires on the back.
I had the same problem with a hobbywing 4585 motor. The motor can is too fat and it touches the outdrive with the stock gear. I also ran a 29 tooth pinion gear. Great video. 👍
great video my friend the way you showed it an the way you took your time to show us i am wanting to build one i us to play with rcs some before i got hurt an now i got hurt an i am cripple from waist down an rc is my life now so keep up the good work
That is similar build different motor two 4s batteries but I had to 1520 1650kv mamba Monster motor with a Mamba Monster X 8s ESC 30 tooth pinion gear in my armor felony
Great video and thanks, I'm sure you just saved me a lot of hours and money as I'm about to jump down this rabbit hole. xlx2 with an 1100 kv and a Limitless are on the way. Also working on a tt02 shooting for 100 MPH on that one. Even us crawler guys need a distraction once in a while LOL.
The stock pinion that comes with the limitless doesn't reach the spur gear like you mentioned. But on mine it's not because it's hitting the drive shaft but simply doesn't reach. The motor mount is pushed as far as it will go towards the spur. So simply stepping up to a 29t pinion with reach the spur ? I have the same motor/each setup as you along with the stock motor mount..,, Thanks.
I was scratching my head, I assumed you stepped up in gearing but couldn't believe the gap between the pinion and spur when I first slid it in place. I have a PPS motor mount on order which will solve all problems but just wanted to run it for a little while before really modifying it. How are your temps with that gearing?
Hey so i did the exact build you did literally everything the same as you did, did you have over heating issues? I would run about 3-4 100mph passes then itll cut off from over heating what am i doing wrong?
How do you set this up to run properly? Mine only runs in reverse, unless I switch the motor to run in reverse, then it goes forward. I dunno if that will damage the motor... BTW I have the same components as yours.
Horizon Hobby has options where you can select which ones you want when you purchase the Limitless through them, but most places you have to buy your own stuff.
Why would you pay almost 1000? The car is 399.99 USD. You do have to pay for your own motor, esc, transmitter, receiver, batteries, servo. What you put in is up to you.
Sorry, I forget, i live in Indonesia, so I have to pay that much, but there are also those who only cost 500 dollars. But even though it's expensive, why only get the frame?
So you can use whatever electronics you want. Some people don’t want the spectrum stuff. So rather than buying a felony or infraction and then selling off the stock stuff, they buy this.
hey I want to make this and before I make it what speed do you think it goes because I'm looking for a combo faster than 80mph (where did you get those wires that your solder down to the wires of the speed controller? PS what is the link to buy those connecters?
This setup got me 117mph. The wires are actually just bread ties with the plastic peeled off. The connectors are OSE8MM. If you search that on google you will find where to buy them. Good luck!
This took some time, but here you go! 1/7 Arrma Limitless Roller www.horizonhobby.com/product/1-7-limitless-all-road-speed-bash-roller/ARA109011.html Castle MMX8S and 1650KV 1717 Motor Combo www.amainhobbies.com/castle-creations-mamba-monster-x-8s-1-6-esc-motor-combo-w-1717-sensored-motor-cse010-0165-02/p1224507 Transmitter and Receiver www.amazon.com/gp/product/B07DPNNTWT/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1 Savox Waterproof High Torque Servo www.savoxusa.com/collections/waterproof-servos/products/new-monster-performance-high-voltage-high-torque-standard-size-servo Batteries www.smc-racing.com/index.php?route=product/product&path=67_96&product_id=549 Battery and ESC Connectors www.offshoreelectrics.com/proddetail.php?prod=ose-qs8-anti
@@GoKaioken I couldn't route it that way. Did you have to remove a little piece of foam to do it? Thing is, once I get the servo in, there is no way for me to get the wire out if the servo housing. It's really weird.
You’re working on a limitless? If your looking at the limitless with the ESC, receiver, and servo mount on the side of the car towards you, when you put your servo in, do the servo wires come out of the servo to the right or to the left?
@@GoKaioken Yes, its a Limitless. I'm working with the Castle 1717 setup like you did. Once I drop the servo in, the wire literally has nowhere to go. The wire on my Servo points towards the front of car.
I too am looking into the Limitless and noticed you have the same TX/RX combo, I also noticed yoy had some reverse issues? I assume it has been resolved and was it a setting in the TX itself? Also noticed you were using a wifi app, I assume that was for the ESC setup you are using? Thanks
I can estimate it for you, but it depends on the brands. For me personally. The motor and ESC combo was about $400. The servo was 150, but it’s overkill for this application, the transmitter and receiver was 80, oh and I forgot to mention the batteries. I have 2 4S batteries 150 each.
@@GoKaioken just which batteries are you using ? Will the car run on one ? Also model of the motor. I’ve been a traxxas guy and new to the game on Arrma.
@@GoKaioken diff question so I’m doing a build with a castle 4pole sensored brushless motor and a xlx 2 8s esc for the armma limitless and do you have any recommendation on gearing
but i still don’t understand what geaeing to run cause the gear has to be the right size for the motor shaft and it has to line up with the gear on that spur gear
Ok first off it’s a limitless made for speed lol you need to start with at least a 34T pinion and if you want real speed you’ll end up with a 39T. Send it!!!
You don't have to take that box out Brody is he box the mom Mamba Monster X it's right in that box bro are you take the top plate off and mount it down everything fits perfect bro 7 had a 1520 1650kv with the Mamba Monster X ESC am I fit perfect he's going to take the top plate off
You just helped me right now with this step by steps instructions I was just looking for something like this for my rc car you are the best man keep the great work up may God bless you.👍👍👍😍😍😍😎😎😎
So glad to hear!
The racers edge capacitor is like a backup power supply. All it takes is a tiny voltage glitch and the receiver will loose binding with the transmitter and will need to rebind to the transmitter and that can take a couple seconds while the car is going 100mph.
Thank you so much for this video it helped me a lot when I was building mine
Great to hear! Glad I could help!
Excellent build great camera angle
So tempted to get one of these. I've always wanted a legit RC car since I was a kid, and now that I have disposable income, I'm feeling the urge.
You’d love it I think
Great Video, I own just about every Arrma RTR besides the Limitless and I want one even though I have the Felony. I think I may just try the body and wing kit with the felony and see how it looks with those bigger tires on the back.
Good job I did the same setup to my Felony and Limitless. Very good💯👍🏽
What’s the name of those motor pinion because for some reason I’m struggling to find a pinion for the limitless
I had the same problem with a hobbywing 4585 motor. The motor can is too fat and it touches the outdrive with the stock gear. I also ran a 29 tooth pinion gear. Great video. 👍
I hear you are extremely happy 😁😁😁 ... Nice build and great setup 👌👍👏 CRAZY Fast🔥🔥🔥
Gotta love the limitless 👍👊☝️
great video my friend the way you showed it an the way you took your time to show us i am wanting to build one i us to play with rcs some before i got hurt an now i got hurt an i am cripple from waist down an rc is my life now so keep up the good work
I’m so sorry to hear that your injury has caused this life altering experience for you. I hope that you can still find joy in your hobby.
Hey, could you send me a link for the pinion gear u used?
That is similar build different motor two 4s batteries but I had to 1520 1650kv mamba Monster motor with a Mamba Monster X 8s ESC 30 tooth pinion gear in my armor felony
Where did u get the cap pack and the cap for the receiver
Great video and thanks, I'm sure you just saved me a lot of hours and money as I'm about to jump down this rabbit hole. xlx2 with an 1100 kv and a Limitless are on the way. Also working on a tt02 shooting for 100 MPH on that one. Even us crawler guys need a distraction once in a while LOL.
Excellent job brother
As strong as those connectors are that catpack solder job don't look like it will last. A glitch buster is to help with connection interference.
So is the glitch buster basically just a capacitor?
Yes
I appreciate this video. I already have the felony but I plan on getting one at some point and getting an infraction
I’m glad it was helpful bro 👍🏻
What batteries are those called?
What does a cap pack do?
Great build and thanks for many tips and ideas, see you on the next one.👍👍💯💯
Thanks!
Where did you get your 29T pinion?
Thank you in advance!
Saga gears online
Hey u ever had an issues with the car spinning out when accelerating past half throttle? I have an xlx2 1100 combo and the car like to 180
Yeah but just at lower speeds. Have to be easy on the throttle lol.
How do you mount the esc skiped that part just glue????
Yes. Sorry about that. Just double sided sticky tape. The thick black tape with red covering works great. Don’t skimp on this part.
Step by step was awesome 👊🏻
I hope nobody does that same wire mess😖😖
What’s the issue?
Nice build for reverse you just need to calibrate the transmitter with the esc and that's all but Tha car looks mean bro I just get the felony love it
Hi. I'm going to try to copy your build as it looks great. Does the esc screw into the holes provided or did you need to do any additional work?
I used double sided tape to secure it down.
Dose to pinion come with the motor or the car when you buy it?
It does come with the car but it was too small. I had a few others that were bigger and those worked.
The stock pinion that comes with the limitless doesn't reach the spur gear like you mentioned. But on mine it's not because it's hitting the drive shaft but simply doesn't reach. The motor mount is pushed as far as it will go towards the spur. So simply stepping up to a 29t pinion with reach the spur ? I have the same motor/each setup as you along with the stock motor mount..,, Thanks.
I think I stepped up to nearly 34 took and 29 spur, something like that.
I was scratching my head, I assumed you stepped up in gearing but couldn't believe the gap between the pinion and spur when I first slid it in place. I have a PPS motor mount on order which will solve all problems but just wanted to run it for a little while before really modifying it. How are your temps with that gearing?
They were fine I bashed around like this for a bit before starting to go for speed runs.
Awesome video! Thank you sir
Do you have to know how to sauder to do a custom build?
If you buy an ESC that does not have battery connectors already soldered.
what is that battery connector that you use? the black with red accent connector from esc?
OSE8MM also known as QS8
Hey so i did the exact build you did literally everything the same as you did, did you have over heating issues? I would run about 3-4 100mph passes then itll cut off from over heating what am i doing wrong?
The gearing may be too aggressive, try gearing down some
Im currently 29p and 34s
How do you set this up to run properly? Mine only runs in reverse, unless I switch the motor to run in reverse, then it goes forward. I dunno if that will damage the motor... BTW I have the same components as yours.
Switching it to reverse will not damage the motor.
what kind of servo did u use for this setup?
Savox 2290
can someone explain what are the caps in the purple warp use for?
These are cap packs and they help stabilize the electrical system under heavy load. It helps protect the batteries as well.
@@GoKaioken OIC Thanks you.
when you buy it do you need to build it or was this just a customized one
It comes as a roller so you need to buy all the electronics and build it yourself.
Nice tutorial but what kind of go pro version you using for video😁
At the time I think it was the 8th
Man these things have come a long way from the RC10.
for assemblies such as batteries, cables, dynamos, etc. already available or sold separately?
Horizon Hobby has options where you can select which ones you want when you purchase the Limitless through them, but most places you have to buy your own stuff.
then we pay almost 1000 dollars, it only gets the car, not including the engine?
Why would you pay almost 1000? The car is 399.99 USD. You do have to pay for your own motor, esc, transmitter, receiver, batteries, servo. What you put in is up to you.
Sorry, I forget, i live in Indonesia, so I have to pay that much, but there are also those who only cost 500 dollars. But even though it's expensive, why only get the frame?
So you can use whatever electronics you want. Some people don’t want the spectrum stuff. So rather than buying a felony or infraction and then selling off the stock stuff, they buy this.
Awesome awesome setup and video.i just got one and am doing all the internals myself.✌👍🔥🔥🔥🔥
Thanks!
sorry Im kinda new to this, Ive done one before but, would basically any receiver and controller work with this?
Yes any should work
@@GoKaioken ok thank you!!
You’re welcome!
Question I was going to buy the car but does it not run out the box
It does not. It is a roller which means it does not have any electronics. You have to buy and put them in yourself.
today is there a new version?
There is and I have one on the way :)
The brake sounds terrible. Can that be fixed?
Why do you think it sounds terrible?
hey I want to make this and before I make it what speed do you think it goes because I'm looking for a combo faster than 80mph (where did you get those wires that your solder down to the wires of the speed controller? PS what is the link to buy those connecters?
This setup got me 117mph. The wires are actually just bread ties with the plastic peeled off. The connectors are OSE8MM. If you search that on google you will find where to buy them. Good luck!
@@GoKaioken oh thank you that helps a lot Have fun!!
Why did your receiver need two antennas?
You’d have to ask the manufacturer.
What cap pack is that ?
What battery are you running for this
Started with a 9700 mah 4S SMC and have since moved to a speed run battery by SMC as well.
yes yes yes
Anyway you can post links to all the parts you had to get with the car? Window shopping a build on one. Thanks In advanced!
This took some time, but here you go!
1/7 Arrma Limitless Roller
www.horizonhobby.com/product/1-7-limitless-all-road-speed-bash-roller/ARA109011.html
Castle MMX8S and 1650KV 1717 Motor Combo
www.amainhobbies.com/castle-creations-mamba-monster-x-8s-1-6-esc-motor-combo-w-1717-sensored-motor-cse010-0165-02/p1224507
Transmitter and Receiver
www.amazon.com/gp/product/B07DPNNTWT/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1
Savox Waterproof High Torque Servo
www.savoxusa.com/collections/waterproof-servos/products/new-monster-performance-high-voltage-high-torque-standard-size-servo
Batteries
www.smc-racing.com/index.php?route=product/product&path=67_96&product_id=549
Battery and ESC Connectors
www.offshoreelectrics.com/proddetail.php?prod=ose-qs8-anti
What connectors are you using?
OSE8MM
How did you route the servo wire to get it into the receiver box?
It comes out the right side so I just routed it around the servo and into the box. Pretty straightforward. Are you having issues?
@@GoKaioken I couldn't route it that way. Did you have to remove a little piece of foam to do it? Thing is, once I get the servo in, there is no way for me to get the wire out if the servo housing. It's really weird.
You’re working on a limitless? If your looking at the limitless with the ESC, receiver, and servo mount on the side of the car towards you, when you put your servo in, do the servo wires come out of the servo to the right or to the left?
@@GoKaioken Yes, its a Limitless. I'm working with the Castle 1717 setup like you did. Once I drop the servo in, the wire literally has nowhere to go. The wire on my Servo points towards the front of car.
Send me a message on Facebook and we can work through it there
Great video 👍🏻
Jus bought my limitless n so far it's a pain in the ass. I thought it was rtr but nope so this my first experience
Take your time and be patient. Hoping this video is helping.
I too am looking into the Limitless and noticed you have the same TX/RX combo, I also noticed yoy had some reverse issues? I assume it has been resolved and was it a setting in the TX itself? Also noticed you were using a wifi app, I assume that was for the ESC setup you are using? Thanks
I had to reverse the motor in the castle app and send that to the ESC as well as on the transmitter. Let me know if you have any other questions.
is your mobile app castle from the esc? or app for the remote?
Yes
@@GoKaioken Hahaa excellent
Hey Josh hope all is well great build thank you, the set up on your phone is it for your control or the castle system?
It is for the castle ESC
Im thinkging about getting one, does it come with all the parts?
It comes with everything except for a transmitter, receiver, motor, ESC, or servo.
@@GoKaioken How much do all of these cost?
I can estimate it for you, but it depends on the brands. For me personally. The motor and ESC combo was about $400. The servo was 150, but it’s overkill for this application, the transmitter and receiver was 80, oh and I forgot to mention the batteries. I have 2 4S batteries 150 each.
@@GoKaioken Thank you!
@@GoKaioken how much could i sell the complete car for?
DId this reciver come with the controller
And does the sensor wire come with the motor
Yes to the receiver coming with controller. The sensor wire does come with the motor
Wow amazing build! Do you know where i can find a cheap 1/10 scale kit pre assembled like yours. Maybe under $100?
Hmm for under 100 I’d say good luck on finding that deal! Lol - but try some Facebook RC groups usually some guys are selling old projects for cheap.
Ok, thanks for the suggestion!
I have a limitless roller for sale. But it doesn't have Radio System, Battery, Charger and Electronics
Slide a strip of notebook paper between your pinion and spur gears for perfect mesh
I prefer to do it manually.
@@GoKaioken sometimes its better that way sweet build anyways
Why is there 2 antennas and what type are the connectors? Great video. Have a blast!!!
Better range for receiver. OSE8MM. Thanks!
Nice build bud, maybe you should but a gyro in there as well.
Do you need hardware?
Yes. This is just a roller so you need to get your own electronics.
Nice build!!! I just picked up a Limitless with a Max6 esc and a 5967 1100kv motor in it.. What part of Ohio are you in? I’m in Youngstown area.
I have family in Ohio but I don’t live there. Will always root for the Buckeyes!
Nice set up bud, what motor and esc set up you habe there and at what speed does it put your limitless?
Castle MMX8S and 1717 Motor 1650kv and it depends on how it’s geared. The setup you see in the video I believe put it at 118.
Which SMC barrerites?
9700
nice build
Thank you!
What is a cat pack?
A cap pack* I would do a quick UA-cam search. They can explain better than me
Josh, can you provide all of the components you are using. I want to get one as wel.
I thought I covered everything in the video.
@@GoKaioken helpful comment.
If I missed something on a product you’re looking for let me know
@@GoKaioken just which batteries are you using ? Will the car run on one ? Also model of the motor. I’ve been a traxxas guy and new to the game on Arrma.
SMC 9700, yes, Castle 1717, covered.
What is the angle on that servo?
I’m not quite sure what you mean.
@@GoKaioken what servo do you use
Savox 2290sg
So wanna get one
Hey bro if you could reply somehow to me it would be nice but my question is how fast does that custom build go?
This one went I believe 112
@@GoKaioken I’m trying different parts to it would you be able to tell me if it’s good or not? Is so let me know because this is my first build
What parts are you using?
@@GoKaioken diff question so I’m doing a build with a castle 4pole sensored brushless motor and a xlx 2 8s esc for the armma limitless and do you have any recommendation on gearing
Start with 1:1 so 34:34 and go from there
but i still don’t understand what geaeing to run cause the gear has to be the right size for the motor shaft and it has to line up with the gear on that spur gear
Mod 1 gears. Are you still having trouble on what to get?
Hey man I see you are from Ohio. What part are you from
Hey buddy I have family from Xenia but I was born in WV. Die hard Ohio State fan though as is the whole family lol
Joshua Esposito ok I’m from Cleveland that’s why I was asking
I was about to ask you the same thing, I’m just a little bit north of Columbus. I just received the rest of my parts to finish my limitless.
Awesome! I hope the build is going well
Ok first off it’s a limitless made for speed lol you need to start with at least a 34T pinion and if you want real speed you’ll end up with a 39T. Send it!!!
Keep watching 😉
You don't have to take that box out Brody is he box the mom Mamba Monster X it's right in that box bro are you take the top plate off and mount it down everything fits perfect bro 7 had a 1520 1650kv with the Mamba Monster X ESC am I fit perfect he's going to take the top plate off
I think 🤔 I will have me one build might as well 🌚👀🚗💨💨💨💨💨💨💨💨💨💨💨💰💰💰
Jesus you can drive
Can or can’t? Lol
You literally need a runway
The only complicated part, install servo wire, no coverage. Sigh
Please old bandıt send me 😄🙏
Hahaha I’m still gonna try to get to 100 with it.
Joshua Esposito I believe you will achieve this. we will see together 👍😊
where did u get the Allen wrench screw driver set up