Pump and Cap Assembly Troubleshooting Tips
Вставка
- Опубліковано 10 вер 2024
- Join our Facebook group for DTG and DTF here: / 695117382401893
Join our Facebook Support group for our products here: / 731534475102167 To avoid yellowing on light garments you For parts please visit our website and support us so we can continue to produce videos.
www.dtgprinterp...
so the mutoh 1204 i'm working with is not sucking all the ink from the ink cartridge , is this a pump and cap station problem?
could you do a video with how to disassemble and reassemble to the pump and cap
I have the same question. We have an Epson 11880. Unfortunately Epson doesn’t service the Caribbean where we are located. At this time our boarders are closed so can’t fly in a tech to have a look. I’m getting bands in the prints. The LK nozzle appears to be clogged. Now I’m out of work as I can’t seem to work through this issue. We have done a tons of research and would like to clean the pump and cap. Problem is, I don’t know how to disassemble the printhead, ink tubes, pump and cap etc. any advice from the print community would be greatly appreciated.
what happens if the ink is not charging , the ink doesn't go through the tubes ?
I have an Epson T3170x. A technician told me that the error code 0014BD is due to a pump and cap assembly. I hadn’t used the printer in a few months. Is there anyway I can disassemble it myself and clean it and put back together or do you think I’d need a new one? Thank you very much.
Not sure to be honest
Thank you very informative, how do you reset the printer after you replace the pump and cap assembly? Thank you very much
no problem, not sure to be honest but maybe a setting in the adjument wizard program more than likely
Pump cap problem or damper problem?
Hi, after I saw your videos, I don't know what the problem is with my printer.
I haven't used my Epson Stylus Pro 3800 printer for several years. I was not so smart to replace the inkt with e.g. Piezo flush. Now I start printing again I have old cartridges of course, some replaced because the were almost empty. I have after cleaning the print head a rather good nozzle check, but the yellow color was mixed with black/gray. After printing a lot of yellow the nozzle check became good, but still the photo's are not really sharp, a kind of haze, maybe because the old inkt?? Old Photo Paper??
The next day I did a nozzle check again and the yellow was again mixed with black. Do you have an idea what the reason can be?
(sorry for my english)
Thanks in advance,
Ton
sounds like you could have a damper and pump and cap issue combined
HEY MY EPSON STYLUS PRO 4800 NOT INK CHARGING ITS RUNING A INK CHARGE BUT NOW FLOWING IN THE LINES SO NO INK IT PRINTING… ANY HELP PLZ???
This can be several issues, we can arrange a tech to help you. It would be by referral though. This can probably take a while to diagnose so they might ask for a fee
Hi
I have a problem with my epson l1800, impossible to load the ink in the print head, I have used all the possible options. the head is not clogged it is new, the printing pad has been replaced and everything dies when I put product on the printing pad.
No pipes are clogged or damped, everything has been checked.if someone can help me i am at the end of this printer
it sounds like you have a blown fuse on the motherboard. I would take the printer to a computer repair shop and let them replace. Its on the bottom side of the mainboard
@@AnthonyCreekTV the motherboard is new, the old one had burnt out.
Are you talking about fuse F1 on the motherboard? fuse F1 is used to print, right? I managed to get some ink in the head using a pump outside the printer but when I use the pump of the printer nothing comes out, I don't really understand where can come the problem.
I wonder if this is my issue.. epson 2720, smearing black towards the end of every print
yes more than likely or damper issue. Clean the wiper blade very good also
@@AnthonyCreekTV Hm.. I wonder. Because it’s not just a typical smear. It’s very fine little lines. Man, I would so deeply appreciate it if you could help me diagnose the issue. I’d even tip you for your time, lol. Any chance I could get your email or a way I could contact you and send you photos?
I was on the phone with Epson and of course my warranty is voided due to the sub ink.. The guy I purchased from on Amazon is useless. I’m pretty much screwed at the moment.
@@denniss7805 sure send em over, if you can go to our contact page www.dtgprinterparts.com and send us an email. If we put anything here as far as email goes spam bots catch it!
@@AnthonyCreekTV Oh man! You’re really saving me a fuck ton. I’m gonna run some examples and send them your way later this evening.
Thank you!!
@@denniss7805 ok no problem, we have a few workers that watch our emails so if not me then someone else will help out too.
I’m changing mine out should I suck the ink from the lines it’s a week for shipping
Do you ever disassembled an old caping station? At least for the DX5 print heads there is not an actual pump inside. The is a motor driving the cogs and those create a vacuum on the silicone ink lines running through the assembly. As long as the motor works there is no need to replace anything but the cap itself, the wiper and if needed the ink silicone ink lines inside the assembly.
So a bad cap top can cause no ink to load into the print head?
@1sickhemi_92hemi_movement2 yes correct
I solved my problem, it was the second small black pipe which is connected to the ink pad, the valve did not close well for good suction
Ahhhh makes sense
i have a f2000 and i get the error code 1410 i assume i need this part do you know where i can buy it and how much it cost? i am sure i can swap this out myself.
Yes!!!!!
we have them on our website www.dtgprinterparts.com
what is the material of the pumping cap sponge made?
mo ni not sure
Are you telling me when i turn off the printer, it sits over the black box on the p5000?
Not sure on that printer. Have never used it. This video is for an R2400 or R3000 dtg
Im getting inconsistent nozzle checks ! Can u please show where to clean the head and how to clean the cap i like that u showed how it sit and i can actually see the head ! How do u replace the pump or cap and the dampers just incase and what should u change first . I cleaned my head and cap but i dont know when i have to change the cap how do i know its dirty !?? Also can i use alcohol or does it only have to be solvent i dont have that right now. Im new and im getting inconsistent nozzle checks and some horizontal banding on certain colors
Hi, this would be a lot of troubleshooting. Depending on the printer model we can get you over to a tech to help. Visit dtgprinterparts.com and click on the contact link to send an email and let us know the printer model because each printer requires a good tech that is specialized in that printer to help you. The techs are independent that are trusted
Is there a video for damper replacement on the F2000?
My printer is printing rubbish and I have change the toner and the developer but yet still printing shit and I was told it was the pump. My printer is triumph Adler 2500ci how can I change it
not sure with that model printer. I would unplug the usb and power cord and see how it comes out or give it a try. You have 2 options; 1. Limp along and eventually problem gets worse or 2. Give it a shot and try to replace and fix it. Option 2 is not what everyone wants to do but it builds confidence and the outcome is much better than option 1. With option 1 the printer will eventually stop working so you have nothing to lose.
My epson wf7515 is printing the width of the printhead with ink spiling a lot of ink on the page, is it the pump clogged?
sounds like your bottles maybe too high, try lowering them
I put a new capping station assembly in and still nothing.
You might not have it situated properly or could be multiple issues. If you need help we do have technicians on staff you can call. We just need to cover their cost. On our website there's a link for support and plans. They are very reasonable and worth it. Our toll free number is 855-384-7278.
Hi and thanks for this review ... i have a question please : i just changed the ink pump on my Epson 1390 and doesn’t work ! When i start the printer i have two leds who are blinking (flashing) and my question is : does the ink pump need to detect ink ? Because i changed cartridge, carier and ink pump but i did not put ink in the machine at time . May be it is the problem ? THX
reset the purge count in your software
I have an idea the my r3000 capping is at the end of it's life.. it seams very hard to find this item online.. are there any other Epson model parts would interchange with the r3000?
that sounds like a counter that can be adjusted in the adjustment wizard
I thought the dry cap area was where i was supposed to wet cap it
each printer is different, we don't really recommend doing this on other printers that are not for dtg unless its a purpose built dtf printer. No solution should be put anywhere near any electronic components
Define inconsistent nozzle checks
Not the same every time
How do i buy a whole new cap assembly unit?
Deep clothing Brand you can visit our site dtgprinterparts.com
@@AnthonyCreekTV i have but i dnt see the cap assembly unit on there for the epson surecolor f2000
Hey. Im in Sedona Arizona. Where are you located. I have an F2000 for 3 years. Problems, problems, problems. My pump cap assy is clogged. I'm wasting lots of ink & time cleaning only to see it getting worse nozzle checks! I have a spare Pump Cap assy on hand. How much will you charge me to guide me in putting in the new PCA??? Any time & asap. I will pay you for your time. The guy in Phoenix told me he cant help me for a few days & I'm afraid the print head will dry out by them Please help!!!! We can do by phone & I'll pay you. Just help me asap! Thanks.
I’m in Fresno California
I think that he maybe your best bet because he's closer. If you need me call my toll free number 855-384-7278.
@@AnthonyCreekTV thx!!! This guy is unreliable....
@@QuantumBunk call me if you need me