Replace the spokes of a motorcycle model
Вставка
- Опубліковано 6 лют 2023
- Replace the spokes of a motorcycle model
#replacespokes #motorcyclemodel #wheel
I made a jig to increase the efficiency of spoke replacement.
It is recommended to separate the rim and hub when replacing the hub with a disc brake type, when wanting to clean and paint the rim seam, or when drilling holes on the hub side is difficult.
Then replace the spokes.
Therefore, I needed a jig to align the hub with the center of the rim, so I made my own jig for replacing spokes on BMW wheels.
The spokes passing through the hub side of BMW are not bent spokes, so drilling is troublesome.
Impressions of spoke replacement using a jig
I recommend it because it was beautiful and easy to make, such as painting, finish condition, time to completion.
It's nice to be able to change from drum brakes to disc brakes as long as you have a hub.
Material
3mm thick plastic plate
5mm plastic square bar
insect pin
brass tube
1 12 cm square plate with a thickness of 3 mm
Four 2 cm x 5 cm rectangular plates with a thickness of 3 mm
5mm plastic square bar
Wheel and rim offset spacers as needed
The shaft that penetrates the rim is a brass pipe that matches the shaft diameter.
Method
Drill holes in the rim and hub
Same drilling angle on rim and hub
Two sets of spokes facing each other
Set it on a jig and check the center
Assemble the next two pairs of spokes face-to-face and secure with instant glue.
After assembling the four pairs of spokes, separate them from the jig and assemble the remaining spokes.
Set it on the jig, check the center and fix it with adhesive.
It can accommodate motorcycle wheel sizes from 1/12 to 1/6.
Thank you very much. - Навчання та стиль
Your videos are outstanding, I built the triumph motorcycle based on your videos and am very satisfied.
👍
If you have any questions, please leave a comment!
Your Triumph is sure to make a great motorcycle!
Thank you for your comment!
素晴らしい加工技術です👍
治具は大切な加工技術ですよ🥰
治具は矢作さんの足元にも及びません。
あの、アイデアはどこから来るのかいつも感心しています!
Great setup and tutorial. Thank you for sharing!
I would be happy if you could help me with something!
Thank you for watching the video!
Großartige Anleitung! Danke dafür 👏
Hallo!
Vielen Dank für das Ansehen und Kommentieren des Videos.
Danke.
Thank you for this very complete and well presented tutorial.
I also want to make a short HOW TO video!
Thank you for watching the video!
Thanks for the tutorial. Will try to do on my bike model. Arigatou amigo
Thank you! In Ijapanese "Arigatou Gozaimasu"
Vous êtes tout simplement un génie !🙂👍🙏
merci! !
Great vid...... 👍👍
Thank you!!
@@scalemodeler 👍
Thanks you for the inspiration and knowledge, you are doing great work!
Thank you very much for your nice comment!
From Japan!
I want to try this! 👍
You will definitely succeed!
Thank you ❣️
good luck
wow tyre shop!
Thank you! always!!!
Superbe vidéo.peux -t- on le faire avec 1/6 1/8 et 1/12eme? Votre gabarit?
Oui, il s'adaptera aux modèles de roues de moto de l'échelle 1/12 à 1/6 !
Je travaille actuellement sur une maquette à l'échelle 1/8.
スポークを張り替える動画は他所でもいくつかあるようですが
ホイールの左右を貼りあわせた際に生じる合わせ目を消せるのはあまり無いので良い方法ですね
ありがろうございます!リムの接着部分を消したり、ハブの交換とか、BMWのような特殊なタイプのハブのスポーク交換はこうするのが綺麗で楽でした。今後は治具を使って組み立てようと思っています。
Thank you for sharing, Well Done.
Thank you for watching video!!
bonjour super travail j'aimerais avoir votre expérience en plus je ne trouve pas ce genre de matériel en France a bientôt
C'est vraiment dommage !
J'espère te revoir!
@@scalemodeler oui je continue à vous regarder j'adore votre travail je parler juste du matériel que vous utiliser
@@laurentbouveyron5362 merci.
Tu es un ami très cher pour moi.
@@scalemodeler merci beaucoup ces pareil pour moi
ご無沙汰てます
このHow to 有料でもいいくらいです!!
いつも楽しみに拝見してます
もうしばらくバイクシリーズ観たいです(^^)
お久しぶりです!
寂しかったですよ😊
オートバイは1/8でBMWをカフェレーサーにして、CB72をサーファーバージョンにして、トライアンフとハーレー予定していて、1/12で一台ガレージ作って、車に戻ろうと思っています!
また、来て相手してくださいね!
ありがとうございます😊
👍
Thank you!!
looks like a jig i would have made for wood working
You already made a jig! wonderful!
@@scalemodeler lots when i was wood working
👍👍👍👍👍👍👍👍
Thank you🙏😊😊
C' est en quelle matière le gabarit? Merci de votre réponse.
C'est une plaque en plastique d'une épaisseur de 3 mm.
merci!
@@scalemodeler je suis débutant en maquette moto.pensez vous que je puisse savoir faire le gabarit?
Avez vous le lien pour acheter tout ce qu' il faut pour confectionner le gabarit? Merci.
@@jackycherieth4634 Le tout acheté sur Amazon Japon.
La plaque en plastique de 3 mm est un produit Tamiya.
Le fil en acier inoxydable de 0,5 mm peut être remplacé par une épingle à insectes.
Cependant, les épingles à insectes ne peuvent être utilisées que jusqu'à l'échelle 1/9.
Les tuyaux en laiton d'un diamètre intérieur de 0,6 mm peuvent également être utilisés avec des tuyaux en aluminium.
Les tuyaux en aluminium sont faciles à traiter.
@@scalemodeler ok je vais essayer mais ce n est pas évident pour moi.
what is your next bike build
Next is Heller's BMW converted to a cafe racer.
It will be released this week.
thank you!
@@scalemodeler i will keep looking
Every second word in Japanese ends with "MAS" or "YAKIMAS"
This is an honorific word in Japanese. Or it's a polite word.
you make it look easy but i still would not try it
At first I couldn't do it at all, but after some trial and error I made it!
I think it will be easy once you get used to it!
@@scalemodeler how many have you done?
@@leroymitch3153 I do six bikes.
Thank you.
Super, díky!
nemáš zač.
Děkuji mnohokrát!