The flashing should be done over again. There needs to be a curf cut made and the flashing should be embedded into the curf and sealed properly...surface applied flashings are a sure failure
You didn't fix the problem you put a band-aid over it. To fix it right you had to remove the metal then you could fix it the way you did. The cap sheet underneath the metal is still separated from the wall the way you did it. It might not leak now but if you get a heavy rain fall with 6 or 7 inches of water it will. So to save 2 or 3 hundred dollars you did it over the metal and your the roof Dr. Just put on another band-aid on it.
Thats not right. I have repaired my flat roof exactly this was 3 years ago. And since then no water damage came back. And i live in aregion with regular heavy Rain.
Okay, so you are saying that I should remove the metal, do what he did but directly where the roofing material comes up, then put back the metal. And then what? Should I leave the opening at the upper part of the metal open or should I still seal it with something?
I built a shed and i just have plywood for the roof it does well but in between the ply wood water rain water goes threw what can I put in between the plywood to waterproofing to stop the water?
Hello Sir, excellent work! But i have a question. I have the same Problem with water coming in from above the flashing. But my house wall is insulated with styrofoam panels. So directly above the vertical metal bar are the styrofoam panels and they are 15 cm thick coming out. So i have no space to seal the flashing. I hope you understand as my english is not the best. I am from Germany... And also i would need to know what ingredients are in the sealant that you are using because here in germany we will not have the same products.. I hope you could answer me, because all companys who where lioking for my flat deck dont want to repair it they want to make it completely new but i am sure its exactly just this problem thank you very much
Can I use this product on my metal shed exterior concrete floor to bottom of the building joint? I have water coming in and I am trying to fix the problem
It is Charmin Ultra Soft Toilet Paper, just kidding It is a polyester fabric designed specially for this application. You can get it here: bergstromm.com/product/poly-fleece-rolls-2/
The flashing should be done over again. There needs to be a curf cut made and the flashing should be embedded into the curf and sealed properly...surface applied flashings are a sure failure
Curf cut?
kerf cut
You didn't fix the problem you put a band-aid over it. To fix it right you had to remove the metal then you could fix it the way you did. The cap sheet underneath the metal is still separated from the wall the way you did it. It might not leak now but if you get a heavy rain fall with 6 or 7 inches of water it will. So to save 2 or 3 hundred dollars you did it over the metal and your the roof Dr. Just put on another band-aid on it.
Thats not right. I have repaired my flat roof exactly this was 3 years ago. And since then no water damage came back. And i live in aregion with regular heavy Rain.
What do you do if there’s weep holes above the metal? Cover them lol
Okay, so you are saying that I should remove the metal, do what he did but directly where the roofing material comes up, then put back the metal. And then what? Should I leave the opening at the upper part of the metal open or should I still seal it with something?
I built a shed and i just have plywood for the roof it does well but in between the ply wood water rain water goes threw what can I put in between the plywood to waterproofing to stop the water?
Nice clean work!
thanks
Hello Sir, excellent work! But i have a question. I have the same Problem with water coming in from above the flashing. But my house wall is insulated with styrofoam panels. So directly above the vertical metal bar are the styrofoam panels and they are 15 cm thick coming out. So i have no space to seal the flashing. I hope you understand as my english is not the best. I am from Germany... And also i would need to know what ingredients are in the sealant that you are using because here in germany we will not have the same products..
I hope you could answer me, because all companys who where lioking for my flat deck dont want to repair it they want to make it completely new but i am sure its exactly just this problem thank you very much
Hi! Love your videos. Please can you tell me: what is the “fleece” that you always use? Is there another name? Is “reinforcing scrim” the same thing
Fantastic work boss 👍
How to remove all the water underneath??
Where are you guys based out of? Sound like I am hearing a fellow South African?
Ja Boerman, ek is. Bly al 35 jaar hier in die VSA
Sweetheart very nice 👍🏼 job 🥰
thanks my love
Always love watching your videos! Thank you!
Can I use this product on my metal shed exterior concrete floor to bottom of the building joint? I have water coming in and I am trying to fix the problem
Why does your silicone stick to cement and brick but the silicone caulk does not ?
Whats the difference between super Silicone and poly seal?
How about the floor? I noticed you cut into it and water came pouring out. How did you repair that?
Please can you recomend the product,I'm in UK iv got no idea bit noone wants to come help me so I need to try mysekf
Very nice presentation sir.
Ok we see, we see it. Lets see how to fix the issue.
🎉🎉❤❤very nice
Thanks for info
What is the name of the white paper or cloth you use between the paint? Thanks
It is Charmin Ultra Soft Toilet Paper, just kidding It is a polyester fabric designed specially for this application. You can get it here: bergstromm.com/product/poly-fleece-rolls-2/
@@FlatRoofDoctor Thanks
@@FlatRoofDoctor I am in Canada. I can only buy Henry 100% Silicon White Roof Coating. Do you think I can use it as well? Thanks in advance.
@@FlatRoofDoctor thanks
@@FlatRoofDoctor 🤣🤣🤣