You touched on most everything but I did not see that you had the rear door sill protector, but did you mention it? I was breezing through. There are also sentry mode stickers you can get. All the lights in the car can be replaced with brighter ones. The footwells, trunk, puddle lights as well as the glovebox. There is also a stop for your glovebox to keep things from falling out. Stronger struts/springs to make both trunks pop open all the way on their own. Roof rack bars. Rear hitch. Also using a traditional usb stick for sentry is not as good an idea as using cards or an ssd. Usb thumb drives are designed for transferring files and saving data for backup but were not designed and are not rated for constant writes and rewrites that sentry/dashcam will use. Cameras, camcorders, cctv and operating systems use cards not usb sticks. What you should do is get a little usb card reader and then use a memory card (again designed for heavy write/rewrite) and put that in the reader and leave that plugged in. You can get little sd/sd micro readers that are one piece and not a corded design. So they end up not being any bigger than many full size usb sticks. The other option is to also get a ssd. (solid state hard drive) Otherwise you might find that your thumb drive will crash or product errors in a few months or short time.
Thanks for taking the time to make a video. A few observations. 1. Always use two hands to pull the hubcaps off. I know you were holding the camera, but I was hoping that plastic wouldn’t snap. 2. It appears you may have mounted your screen protector upside down. There should not be a gap in the top corners. The screen is actually a couple of millimeters smaller along the bottom. And 3. The front license plate holders are actually about $70-$160 and are quite solid. The advantage to them is that you aren’t sticking anything on your bumper. I’ve got extra seals on my doors but haven’t considered the trunk or frunk. Good idea.
Thank you Kevin, valuable feedback. Trying to film while working with one hand has always been a challenge. Never thought the screen protector is unidirectional, good observation. Thank you.
jjcentral Sure thing. My screen protector actually mentioned it in the directions. I have The Law front license bracket. The Bandit is another good option. I just like the look of The Law better. There is another guy who sells a magnetic holder too that is quite slick.
You need to cut holes in the seals of the door you put on. There's drainage holes in the bottom, and your seal will trap water and cause the door to rust. Just cut holes where those drainage holes are located.
Love the look of the wood-look wrap on the centre console. Why Tesla chose to do the gloss black I don't know - it shows all the finger marks and tiny scratches, totally silly decision!
Nice, informative video Sir. Thanks for sharing your thoughts! Hey if you haven’t done so, check out the usb hub with secret storage for your flash drive. #TeamBlack
I'm wondering where you purchased your wood wrap for center console , it's the best I've seen . The one offered on Amazon right now is not as nice and the grain is vertical not horizontal like yours . Please let me know thanks
Good video. Most of the comments are about the links of the items you recommend. Constructive feedback : include the links in the video description in the future. Can you please provide the link of the magnetic phone mount used under the screen? Thank you
Thanks Yacouba, as mentioned all the accessories were bought on Amazon or eBay. Links seems to change a lot so I don't post all of them. Just search you will find it. www.amazon.com/Foldable-Magnetic-Dashboard-Universal-Smartphone/dp/B07K56NPCR/ref=mp_s_a_1_9?keywords=model+3+phone+magnetic+holder&qid=1573134606&sr=8-9
How did you get at NEMA 14-50 pulg on the Tesla wall connector? I don't see that as option on the Tesla store website? shop.tesla.com/product/silver-wall-connector
Just thought I'd share a Model 3 accessory that I purchased on amazon and thought you guys might really like. EVNV Tesla seat cover (B08FGKVLXB.) They are pretty simple but they fit the seat really well and offer good protection. NO more sand on my car seats!
Good question, the hard wired model can push out 48 amps while the plugged model pushes out 40 amps max. Having said that my car's onboard regulator caps at 32 amps, so no difference for me or any model3 owners, Model S and X you will see a bit faster charge in the hard wired setup.
Right now I have BMW 740 X drive 2015, I was thinking to get an electric, but this tesla car with the money they charge looks from inside like a piece of crap(kia like) and not a luxury car. Nio has luxury inside( was designed by BMW engineers) and I will buy Nio es6 or es 8 when they finally sale in USA
If they included all those accessories then they would have to raise the price accordingly. And most of there’s are completely unnecessary. So it’s better to keep the price low for everybody and then you can customize if you choose to
I hate the carbon fiber look. I was going to use a matte black wrap for the center console but I like yours better. It really matches the wood. I would suggest not using the goop that is included with the Tesla air pump, it will ruin the tire pressure sensor and it would need to be replaced. Use a tire plug kit instead. Also, there is no such thing as a 220 volt outlet, it's 240 volts. You also failed to mention how using the mobile charging cable with the 240 adapter charges at a slower rate than your plug in wall charging cable, and that one charges slower than the hard wired wall charging cable.
Good catch with the 220v mix up, yes it is a 240v outlet with a 220v supply. I do not see any difference between charging with the mobile or wall charger, the inbuilt car regulator caps at 32 amps in both cases for the SR+, may be the M3 LR and the model S,X will charge faster on the wall charger.
@@JJCentral-DIY again, the supply is not 220 volts, it's 240 volts. Everyone seems to confuse this. 110v/220v hasn't been around in like forever, it's 120/240v now.
Please provide links for your accessories
You touched on most everything but I did not see that you had the rear door sill protector, but did you mention it? I was breezing through. There are also sentry mode stickers you can get. All the lights in the car can be replaced with brighter ones. The footwells, trunk, puddle lights as well as the glovebox. There is also a stop for your glovebox to keep things from falling out. Stronger struts/springs to make both trunks pop open all the way on their own. Roof rack bars. Rear hitch. Also using a traditional usb stick for sentry is not as good an idea as using cards or an ssd. Usb thumb drives are designed for transferring files and saving data for backup but were not designed and are not rated for constant writes and rewrites that sentry/dashcam will use. Cameras, camcorders, cctv and operating systems use cards not usb sticks. What you should do is get a little usb card reader and then use a memory card (again designed for heavy write/rewrite) and put that in the reader and leave that plugged in. You can get little sd/sd micro readers that are one piece and not a corded design. So they end up not being any bigger than many full size usb sticks. The other option is to also get a ssd. (solid state hard drive) Otherwise you might find that your thumb drive will crash or product errors in a few months or short time.
Thanks for the info; it was very helpful and practical.
Thanks for taking the time to make a video. A few observations. 1. Always use two hands to pull the hubcaps off. I know you were holding the camera, but I was hoping that plastic wouldn’t snap. 2. It appears you may have mounted your screen protector upside down. There should not be a gap in the top corners. The screen is actually a couple of millimeters smaller along the bottom. And 3. The front license plate holders are actually about $70-$160 and are quite solid. The advantage to them is that you aren’t sticking anything on your bumper.
I’ve got extra seals on my doors but haven’t considered the trunk or frunk. Good idea.
Thank you Kevin, valuable feedback. Trying to film while working with one hand has always been a challenge. Never thought the screen protector is unidirectional, good observation. Thank you.
jjcentral Sure thing. My screen protector actually mentioned it in the directions. I have The Law front license bracket. The Bandit is another good option. I just like the look of The Law better. There is another guy who sells a magnetic holder too that is quite slick.
Kevin Moncrieff I’m looking for a magnetic phone holder. Could you provide a link? Thank you.
You need to cut holes in the seals of the door you put on. There's drainage holes in the bottom, and your seal will trap water and cause the door to rust. Just cut holes where those drainage holes are located.
Thank you for pointing that out. Will inspect.
Solid video! Really enjoy the wood center counsel.
Thank you.
A very helpful video. Thank you. I'll use your referral code when I order my Model 3 Performance.
Thank you sir and good luck to you
Love the charger ideas man
Love the look of the wood-look wrap on the centre console. Why Tesla chose to do the gloss black I don't know - it shows all the finger marks and tiny scratches, totally silly decision!
Great ideas. Thanks.
Where'd you get the wood wrap from?
Nice, informative video Sir. Thanks for sharing your thoughts! Hey if you haven’t done so, check out the usb hub with secret storage for your flash drive. #TeamBlack
Remember, any time you give a ride to a non-Tesla owner, an angel gets its wings!!!
Good video with great suggestions but you fail to give a reference as to where to find or buy an item.....THanks
Super👍
Does the wood color center console wrap match the interior woods? Also is the Tesla Bro’s wrap?
Yes, the color match is exact and even close on the texture.
I'm wondering where you purchased your wood wrap for center console , it's the best I've seen . The one offered on Amazon right now is not as nice and the grain is vertical not horizontal like yours . Please let me know thanks
Can you link these accessories?
Thank you! Super helpful video!
What brand is that phone magnetic holder?? Do you have a link for it? Thanks in advance!
Good video. Most of the comments are about the links of the items you recommend. Constructive feedback : include the links in the video description in the future.
Can you please provide the link of the magnetic phone mount used under the screen?
Thank you
Thanks Yacouba, as mentioned all the accessories were bought on Amazon or eBay. Links seems to change a lot so I don't post all of them. Just search you will find it.
www.amazon.com/Foldable-Magnetic-Dashboard-Universal-Smartphone/dp/B07K56NPCR/ref=mp_s_a_1_9?keywords=model+3+phone+magnetic+holder&qid=1573134606&sr=8-9
Sir, where and how much is the magnetic phone mount? How did you attach it to the back of the screen? Thanks
Could you please provide the link to the center console wooden wrap ? Thanks and good video
Adolfo Montero I would also like this link
@@thatlocalrealtor you can get those at www.rpmtesla.com or evannex.com. www.abstractocean.com might have them too.
How did you get at NEMA 14-50 pulg on the Tesla wall connector? I don't see that as option on the Tesla store website? shop.tesla.com/product/silver-wall-connector
Many of these things can be bought much cheaper from Aliexpress. Directly from china. The amazon things are often from aliexpress..
Just thought I'd share a Model 3 accessory that I purchased on amazon and thought you guys might really like. EVNV Tesla seat cover (B08FGKVLXB.) They are pretty simple but they fit the seat really well and offer good protection. NO more sand on my car seats!
Hey if you don’t need your 1450 adapter would love to buy it from you!
Wood wrap?
Could you try the steel ball test on the screen protector for us? Thanks
I don't have balls of steel to try that. However the protector is more to prevent scratches more than anything.
Does your wall charger with the 15-40 plug charge as fast as the charger that does not have a plug (needs to be wired directly) ?
Good question, the hard wired model can push out 48 amps while the plugged model pushes out 40 amps max. Having said that my car's onboard regulator caps at 32 amps, so no difference for me or any model3 owners, Model S and X you will see a bit faster charge in the hard wired setup.
what magnetic phone holder is that??
Half of your "25 must have recommendations.... you don't have"
Can you share a link to where you purchased the center consul wrap the wood look is nice.
www.amazon.com/ROCCS-Console-Protector-Sticker-Decoration/dp/B07T11FG99/ref=sr_1_2?keywords=model+3+wood+vinyl&qid=1572145733&sr=8-2
www.rpmtesla.com/collections/model-3-center-console-wraps/products/model-3-vinyl-wood-console-wrap-gen-1-or-2-69-w-20-off
How easy or hard was it to install door seals?
It was pretty easy on the outside edges, behind the hinges was a challenge. Took 20 minutes per door.
Home link comes with other cars that around 40,00 and above
$130 for WeatherTech floor mats for the Model 3.
So yours doesn't have the Homelink option for the garage?
No, that is a extra dealer installed option
Right now I have BMW 740 X drive 2015, I was thinking to get an electric, but this tesla car with the money they charge looks from inside like a piece of crap(kia like) and not a luxury car. Nio has luxury inside( was designed by BMW engineers) and I will buy Nio es6 or es 8 when they finally sale in USA
MyQ Smart garage opener solves the garage issue for $19.99
Do you use the phone to control the garage door in myq app or is there a Tesla integration somehow?
Could you share me link for magnet phone mount pls...?
www.amazon.com/gp/product/B07K56NPCR
For the price they’re charging for this car all of this should be standard.
If they included all those accessories then they would have to raise the price accordingly. And most of there’s are completely unnecessary. So it’s better to keep the price low for everybody and then you can customize if you choose to
Screen protectors protect screens from a fall. lol
niacal4nia smudges or a kid in the back seat playing with a ball. Lots of reasons for screen protectors
Maryland 💛❤️💛❤️
Where do you get off saving a charge spot with a cone!! Selfish
i skimmed parts of this video. what are you referring to?
I spent $90000 on weather tech mats lol
I think you overpaid :(
Frzenflme nah brah it’s coo
bling bling
I hate the carbon fiber look. I was going to use a matte black wrap for the center console but I like yours better. It really matches the wood.
I would suggest not using the goop that is included with the Tesla air pump, it will ruin the tire pressure sensor and it would need to be replaced. Use a tire plug kit instead.
Also, there is no such thing as a 220 volt outlet, it's 240 volts. You also failed to mention how using the mobile charging cable with the 240 adapter charges at a slower rate than your plug in wall charging cable, and that one charges slower than the hard wired wall charging cable.
Good catch with the 220v mix up, yes it is a 240v outlet with a 220v supply. I do not see any difference between charging with the mobile or wall charger, the inbuilt car regulator caps at 32 amps in both cases for the SR+, may be the M3 LR and the model S,X will charge faster on the wall charger.
@@JJCentral-DIY again, the supply is not 220 volts, it's 240 volts. Everyone seems to confuse this. 110v/220v hasn't been around in like forever, it's 120/240v now.
Vacuum that driver side!
You know, right? :)
yikes...needs a bit of cleaning
This guy's phone pad is upside down and his phone cradle blocks the screen, I can't take him seriously.
Dirty Car, ill fitting mats and trunk mats - not really inspiring?
Well... Looks like you would love it then when I show the car with a bale of hay and chicken feed.
@@stevensosna2003 finally ordered a proper fitting mats for floor and trunk for the winter. Will show case that in another video. Thanks
Tu indian hai samjha teri baato say he lagraha hai