Watched this again, caught more the second time around. Thank you Harv. Looking forward to the next part and praying for your full recovery. You're the man Harv.
The piston wear is due to stroke, rod length and angle not the pin position. The rod ratio is well known 'phenomena' and promotes a lot of discussion. (and even more misunderstanding) Rod ratio's are usually in the 1.6 to 1.9 : 1 range, depending on what the designer was aiming for and intended use. Longer rods put less skirt load on piston simply because there is less rod angle at 90 degrees after TDC. I'll let everyone into a little (well known') 'secret' relating to the intake port you showed. That will have bad flow but it may be deliberate to cause extra turbulence and mix fuel better? Air doesn't like to change direction. If you look up some old NACA research from 1940's, about seven degrees is maximum divergence even on a fully pressurised system. I'm kinda old, been doing two stroke (and four stroke) motorcycles since early 70's.when piston porting was the only thing around Saws look a lot cheaper to mess with when you can buy a new Chinese motor for less than $100. Squish clearance closes up pretty good due to ball and roller bearings 'everywhere' plus con-rod stretch, piston just clearing head at max rpm is OK but may destroy several engines before you find the minimum. I found a one degree difference between piston crown and head works real good with about 0.038" on motors I've built. I don't usually work on 40mm bore or smaller cylinders though, 54~56 mm is usual for a 125 MX bike
I have followed your information to the letter on my first 372 build and it’s truly unbelievable. The response and power in the cut is night and day over stock . My buddies that have seen heard and ran this saw know . Full faith in you Harvey your specs are perfect buddy , thank you for your guidance and information sharing. No machining needed to get impressive gains . 🇦🇺👍🏻🇦🇺✊🏻
I just finished modding my g372xp. I am outside of your specs. I didn't want to do any port work so this is what I did . I modded the exhaust per your instructions on one of you other videos witha 3 inch piece of 3/4 inch pipe. I unshrouded the bottom of the tansfers by cutting the flanges out of the way. I installed 3 base gaskets and a slab sided flat top 268 piston. I ended up with .025 squish, 160 degrees intake duration and 155 exhaust. I just finished it and made a couple of cuts. I am impressed with how the saw runs. Maybe not ideal but it is definitely stronger now with minimal effort. Maybe I will epoxy the bottom of the intake next. Bring it to 150 degrees.
Ironhorse, if I get a Hyway cylinder kit for my 372xp , do I need to check any of the timing on the ports if it just stock. I'm just using it for firewood gathering and don't need it hopped up .😊appreciate your input .
Hi Harvey, You methods of saw building have worked for me. I add one of my custom pipes and a sharp chain, and that equals reliable pure fun! Thanks for sharing your years of experience, that can't be replaced!
Hello buddy, hope u r getting u some rest/sleep. But what is tht bhind u Mr. Harvey 🤷♂️ im building a little 355 roller motor right now for my lil 98 stepside s-10. I got a set of dome pistons for it, have a nice cam for it also, @50 its a 254/266 with .600 lift. Thts with 1.5 rockers. Anyway i hope and pray ur Dr can get u all fixed up so u can keep doing what u love to do. And thts building saws 🙏 GETRDONE Mr. Harvey 🤙
I’ve watched your videos from 3 years ago over and over. Ported my 372 this winter from what I’ve learned from your videos. Big bore gasket delete.Thanks Harvey saw runs great.
So I've been watching your video along with a couple other guys that build two strokes and it seems all of you guys do smaller engines so my question is I have 139 cc I want to put on a mini bike what would be the best port job to do like should I raise the exhaust port or what would be beat any advice would be greatly appreciated
Bless you IRONHORSE for sharing your life and wisdom with us:) God Bless and Protect you and your loving family:) We love you IRONHORSE, any time with you is a true Blessing to all of us, especially the younger generations:)
Why does'nt IRONHORSE share, what the situation about NOVICE LUMBERJACK's chainsaw, g395 ?? Novice Lumberjack would very much like to have his property back and have reached out to IRONHORSE several times through the past three month, to solve the situation, but to no avail. IRONHORSE has only responded with emty promises and lately just SILENCE ! IRONHORSE !! Please solve the situation !! and give back Novice Lumberjack his rightfull property
I have a question for you....I have an 048-042 and was wondering if the 038 heads are interchangeable? Parts for this seem to be slim and few and far between... And some of the hwy robbers on Ebay seem to think they have gold... so I am looking for possible interchangeable parts...
hi harvey.very good explaining.a have a question.what you think its better in intake polish and smooth or little bit rugged surface?have heard many teories about it.
IRONHORSE, the information that you are sharing is invaluable and has historical value. You are share the wisdom of your years, may God Bless your kind and loving soul for sharing with us. You are Blessing everyone and it is being captured for historical educational reference:) You are everyone's hero IRONHORSE, you are just an amazing inspiration to all:)
Just discovered your channel, and I am impressed. I am out of action for a while due mishap and interested in building solid work saws. After watching your other videos, am curious what the recipe you would lean(pun) to for an aerial saw for steering softwood/hardwood tops. You have mentioned the scenario in your videos but as far as I can tell haven't discussed the super reliable but performance logging/topping (work saw) incl keeping vibration down
Ya got to keep up the maintenance, change oil adjust the valves, to keep it running properly, and valve overlap is very important, you would think that would hurt performance, but it is almost everything, 😆 what's that to your right shoulder, the Saw is that for 😆,. It's just like the wrong cam , good day✌️
Thank you so much for sharing your knowledge! I built a 359 modeled after what you shared on tin man's 372 build. OMG! That little saw is an absolute animal! It contends with many of my 72 Cc saws. I wish I could say I fully understand everything your saying. I don't, but the principle makes sense and I'm trying to apply it and learn as I go. Thanks again. Take care of yourself.
Glad to see you getting back out to your shop , your channel is terrific. … Question, with the exception of carbon deposits in transfer ports , is there a way ( ie:piston reading) that one can tell if the transfers are to high ? I take your knowledge quite seriously & it HAS changed some of my techniques,again thanks IRON Horse
I dont know what to say, re-affirming, learnin... this is getting really good now, working the individual parts to get numbers more so than machining and helping a little bit of everything, everything I've ever done to my saws per exact uncle harv teachings have and are amazing machines. Look good buddy good to see ya
Awesome info as always thank you from NZ 🇳🇿 ! Any chance in future of getting a video on Porting a dolmar 9010 ? Seems like a great platform for building a torque monster with the large stroke ! Take it easy man !
I’d be really interested to better understand how it all changes when you add reeds into the mix and how that affects blowdown or if at all. The way some pioneers p series are designed almost makes me think they’re made to shorten the blowdown
A reed valve motor allows for asymmetric intake timing but doesn't change much else. The intake can 'open' as soon as there is crankcase depression which would generally be a 'free port' without the reeds. Prior to reed valves, it was far more common to have a rotary (disc )valve opening directly into crankcase. It does make motor wider though. You still have piston controlling transfer timing and exhaust timing
Thank you Harvey for your expertise in two cycle performance design. I don’t really understand it yet, but I very much appreciate the passion and hard work you put into explaining this to us. I like the whiteboard tutorial someday, as a picture is worth a thousand words. I do like listening to your words so maybe we can get both.
Hello there Harvey and hello to the saw community I was just wondering if you know of a lighter riste pin that I could use in a Husqvarna 262xp if you could let me know that would be great and eny other recommendations thanks
IRONHORSE, do you know what you have made run better for me and my family, you showed me how to live a moral, respectful, high integrity life in gratitude:) You have Blessed me and my family. You made me a better husband, father and man in life. Bless you for that IRONHORSE:)
Love your videos. So I have a 462 with intake and exhaust at 160 degrees..... I'd have to run a piston with lower skirt to get 154° and should I delete base gasket cause that's just gonna Increase the intake? Thanks
Harvey I've got a question that nobody seems to be able to answer, maybe somebody can answer it here. I understand the oil gas mix, but how is that delivered to the rotating assembly? How does the bottom end receive its lube to the bearings? I've asked this question on a couple real popular saw channels and have gotten completely different answers. Anybody feel free to chime in?
@@williamwallace9620 are you suggesting that the cylinder and the crank case are hollow and connected in such a way that the mix has a way to reach the rotating assembly and then make its way back into the cylinder? You could be right, I've gotten so many different answers regarding this. thanks for your opinion.
@@williamwallace9620 you did a nice job explaining that,I'll buy it. I'm pretty engine savvy but have never torn a saw down to see how it all jives, thanks again for your time
I’d like to see a longer rod and a gudgeon pin closer to the top of the post too. Same stroke but would be a much stronger combination. Though I don’t know how far you could take it. In the performance V8 world like in your last video, some pins are are so high, they have to make special plugs to support the rings. However, that could be pushing the envelope way too far for a saw
That platform likes good intake flow better than anything. It also helps to widen the bottom of the transfer ports. That's what has worked well for me.
Hi Harvey ~ I ran into an older (3 year old) Ironhorse video in which you couldn't sleep until you compared the stock jug from a Dolkita 7900 to a bigger top end you had in your shop. We now have a brand spankin' EA7900P here, so I'd really like to learn whether or not that upgrade actually panned out for you? Did you make an additional video about that 7900? I've just liked and subscribed, so please keep up with the fine video work, sir.
On my 372 with a 272 piston I used some of your knowledge I angled my upper transfers up above my popup piston and not to raise the transfer too much It helped. Today I did a experimental muffler mod and it really runs strong now. I agree too much machining can hurt performance like making the combustion chamber small and making the area for the explosion small so there is less area to push on the piston. Which means less power.
If anything, we should be tapering everything opposite to flow direction. To build velocity. That also slows the velocity at which the flow comes back in for the exhaust or out for the intake. Could probably also do that on the transfers.
Hey Ironhorse! I just ordered some parts for my Stihl 660. I ordered a 54mm pop up piston. Would you recommend a gasket delete as well? Would you have went with the big bore?? 🙏
Rule number one…. Harv is right and your wrong. Rule number 2. See rule number 1. Ive noticed that high compression saws tend to vibrate more. Have you experienced this? High compression is good and all but after so much your fighting the compression and going backwards arnt ya? Im no professional but i dont care for super high compression saws.
Yer right Kyle! Too much compression and the piston slowes down too much before tdc! And then it fires real hard accelerating the piston! This is where the vibration comes from!
Long intake duration and too high transfers(not enough blowdown)will use alot of fuel. Also if your upper transfers are poorly shaped you will have short circuiting happening. Long intake creates spitback and wastes fuel. Higher you go on transfers more you will short circuit fresh air fuel charge trough exhaust port and muffler instead of keeping it in the chamber and making power. There is a point when givin the saw more fuel does nothing and if you build work saws you want to have good fuel economy. I dont port for living but its just common sense.
Folks can yap away till the cows come home about blowdown , machining,port shapes, widths , duration ,squish bands , pistons mods , dynos and any number of alterations to enhance the performance of a chainsaw. Imho the modded saw must 1) increase cutting speed, 2) get good mileage and 3) last near as long as a stocker for it to be worth a damn …. A 70cc “built” saw with a sharp chain should be able to pull 1in /sec or better using a 24” bar/chain thru a 21-22” log/round (HARDWOOD not pine or balsa) with larger cc saws maintaining this 1in/sec with longer bars / bigger diameter wood. This is where da rubber meets the road and what separates the wheat from the chaff ! IF the saw cannot pull this 1in/sec (or better) than hit the bricks 🧱 bub. All this 2-stroke theory was worked out 50 YEARS ago by men much smarter than either you or I - These gospel according to masterboob , must be machined / 12 deg of blowdown high compression wondersaws simply cannot pass the 1in / sec standard in REAL HARDWOOD ! They just CANNOT DO IT hee hee hee 😂
@@jerseyjoshua4818 has nothing to do with me so I cld care less that's for anyone that has a issue to deal with. Buckin Billy is a no bullshit tell it like it is guy and watching him run a iron horse saw is all the proof I need as far as build quality. Don't want anything to do with all the other bs drama
LMFFAO!!! When us crazy guy’s get older that whole fear of doing life in prison isn’t nearly as scary when you might only have a dozen or so of those left!!! 😂😂😂😂. Those older fella’s shouldn’t be messed around with because they don’t have as much to loose the older they get!!! 😂😂😂. I’m all about 154 and not more then 156… but I just can’t really do anything without see my port mapping and actually seeing the engine!!! I just love when you are feeling scrappy brother!!! LMFFAO!!! I’m an old redneck boy so a good scrap is always fun! 😂😂😂. You’ve helped a whole bunch of guy’s build them a really decent work saw and they didn’t have a lathe and they have a strong runner! And obviously if a guy has a lathe he’s going to be able to get a stronger engine if he’s doing it right! Just cutting the popup into the taller pistons is the huge benefit as well as trimming the base’s!!! Great video Harvey! Nothing but love for ya brother!!!
Gracious, confident, beatin down . And still sharing and helpin’ love wins
Love watching your videos, trying to absorb all of your knowledge Thank You
This information is pure gold:)🙏🙏🙏🙏🙏🙏🙏💖💖💖💖💖💖💖👍👍👍👍👍👍👍
Keep it coming! I’ve learned so much from your vids. 🤙🏼
Howdy Harvey, great to see you!
Watched this again, caught more the second time around. Thank you Harv. Looking forward to the next part and praying for your full recovery. You're the man Harv.
The piston wear is due to stroke, rod length and angle not the pin position.
The rod ratio is well known 'phenomena' and promotes a lot of discussion. (and even more misunderstanding)
Rod ratio's are usually in the 1.6 to 1.9 : 1 range, depending on what the designer was aiming for and intended use.
Longer rods put less skirt load on piston simply because there is less rod angle at 90 degrees after TDC.
I'll let everyone into a little (well known') 'secret' relating to the intake port you showed.
That will have bad flow but it may be deliberate to cause extra turbulence and mix fuel better?
Air doesn't like to change direction.
If you look up some old NACA research from 1940's, about seven degrees is maximum divergence even on a fully pressurised system.
I'm kinda old, been doing two stroke (and four stroke) motorcycles since early 70's.when piston porting was the only thing around
Saws look a lot cheaper to mess with when you can buy a new Chinese motor for less than $100.
Squish clearance closes up pretty good due to ball and roller bearings 'everywhere' plus con-rod stretch, piston just clearing head at max rpm is OK but may destroy several engines before you find the minimum.
I found a one degree difference between piston crown and head works real good with about 0.038" on motors I've built.
I don't usually work on 40mm bore or smaller cylinders though, 54~56 mm is usual for a 125 MX bike
Great Video Harv do you have a lathe that you do machining. Was wondering what your setups are like. Thanks.
hey from Pa, harv, great infoe
Love your videos harv. This is the kind of info we need. Thank you!
Hey great video! Quick question does ring gap and circlip positioning (6-12o clock matter in chainsaws
I have followed your information to the letter on my first 372 build and it’s truly unbelievable. The response and power in the cut is night and day over stock . My buddies that have seen heard and ran this saw know . Full faith in you Harvey your specs are perfect buddy , thank you for your guidance and information sharing. No machining needed to get impressive gains . 🇦🇺👍🏻🇦🇺✊🏻
Hey Marko!
About to build my first OE 372XP. What timing numbers did you go with after a gasket delete?
Marko
@@BuckinBillyRaySmith Buckin
Your throwing Pure Gold Info!!
Thank You Again!!
Great stuff Iron Horse. I don’t understand the haters.
Your looking good and healthy I'm glad to see
I just finished modding my g372xp. I am outside of your specs. I didn't want to do any port work so this is what I did . I modded the exhaust per your instructions on one of you other videos witha 3 inch piece of 3/4 inch pipe. I unshrouded the bottom of the tansfers by cutting the flanges out of the way. I installed 3 base gaskets and a slab sided flat top 268 piston. I ended up with .025 squish, 160 degrees intake duration and 155 exhaust. I just finished it and made a couple of cuts. I am impressed with how the saw runs. Maybe not ideal but it is definitely stronger now with minimal effort. Maybe I will epoxy the bottom of the intake next. Bring it to 150 degrees.
Looking great Harvey !! Blessings sir 🙏 Always great to see a new video 😊
Ironhorse, if I get a Hyway cylinder kit for my 372xp , do I need to check any of the timing on the ports if it just stock. I'm just using it for firewood gathering and don't need it hopped up .😊appreciate your input .
It will be fine!
Guys harvey is on the money. Good job bud
Thanks Donny!
👍🆙DW
@ 4:23 instant thumbs up 👍
Hi Harvey, You methods of saw building have worked for me. I add one of my custom pipes and a sharp chain, and that equals reliable pure fun! Thanks for sharing your years of experience, that can't be replaced!
Hello buddy, hope u r getting u some rest/sleep. But what is tht bhind u Mr. Harvey 🤷♂️ im building a little 355 roller motor right now for my lil 98 stepside s-10. I got a set of dome pistons for it, have a nice cam for it also, @50 its a 254/266 with .600 lift. Thts with 1.5 rockers. Anyway i hope and pray ur Dr can get u all fixed up so u can keep doing what u love to do. And thts building saws 🙏
GETRDONE Mr. Harvey 🤙
Just learning this stuff. Really anxious to see your part 2 to this. I like pictures too! Thanks!!
I’ve watched your videos from 3 years ago over and over. Ported my 372 this winter from what I’ve learned from your videos. Big bore gasket delete.Thanks Harvey saw runs great.
So I've been watching your video along with a couple other guys that build two strokes and it seems all of you guys do smaller engines so my question is I have 139 cc I want to put on a mini bike what would be the best port job to do like should I raise the exhaust port or what would be beat any advice would be greatly appreciated
Bless you IRONHORSE for sharing your life and wisdom with us:) God Bless and Protect you and your loving family:) We love you IRONHORSE, any time with you is a true Blessing to all of us, especially the younger generations:)
Why does'nt IRONHORSE share, what the situation about NOVICE LUMBERJACK's chainsaw, g395 ??
Novice Lumberjack would very much like to have his property back and have reached out to IRONHORSE several times through the past three month, to solve the situation, but to no avail. IRONHORSE has only responded with emty promises and lately just SILENCE !
IRONHORSE !! Please solve the situation !! and give back Novice Lumberjack his rightfull property
Please keep making the best vids & piss'n people off
I have a question for you....I have an 048-042 and was wondering if the 038 heads are interchangeable? Parts for this seem to be slim and few and far between... And some of the hwy robbers on Ebay seem to think they have gold... so I am looking for possible interchangeable parts...
Great information Harvey, thanks for sharing👍🏻
Harvey takes us to school. Love it, great to see you getting better.
hi harvey.very good explaining.a have a question.what you think its better in intake polish and smooth or little bit rugged surface?have heard many teories about it.
Rough will keep the fuel in suspension better and create better air flow!
@@theironhorse6600 yes, thats what a have saying too allthe time.but like you know there is many therories.
IRONHORSE, the information that you are sharing is invaluable and has historical value. You are share the wisdom of your years, may God Bless your kind and loving soul for sharing with us. You are Blessing everyone and it is being captured for historical educational reference:) You are everyone's hero IRONHORSE, you are just an amazing inspiration to all:)
Widening the exhaust ever run into the ring seperation?
Just discovered your channel, and I am impressed. I am out of action for a while due mishap and interested in building solid work saws. After watching your other videos, am curious what the recipe you would lean(pun) to for an aerial saw for steering softwood/hardwood tops. You have mentioned the scenario in your videos but as far as I can tell haven't discussed the super reliable but performance logging/topping (work saw) incl keeping vibration down
Good job
Nice to see you out in the shop looking healthy Harvey. Thanks for your knowledge and advice.
I listened to this two or three times while I was mowing and just watched it
Love the info thanks for sharing
Ya got to keep up the maintenance, change oil adjust the valves, to keep it running properly, and valve overlap is very important, you would think that would hurt performance, but it is almost everything, 😆 what's that to your right shoulder, the Saw is that for 😆,. It's just like the wrong cam , good day✌️
Thank you so much for sharing your knowledge! I built a 359 modeled after what you shared on tin man's 372 build. OMG! That little saw is an absolute animal! It contends with many of my 72 Cc saws. I wish I could say I fully understand everything your saying. I don't, but the principle makes sense and I'm trying to apply it and learn as I go. Thanks again. Take care of yourself.
Good afternoon Harvey
Glad to see you getting back out to your shop , your channel is terrific. … Question, with the exception of carbon deposits in transfer ports , is there a way ( ie:piston reading) that one can tell if the transfers are to high ? I take your knowledge quite seriously & it HAS changed some of my techniques,again thanks IRON Horse
Thanks for sharing your knowledge in the interests of propogating your passion - God Bless!
I dont know what to say, re-affirming, learnin... this is getting really good now, working the individual parts to get numbers more so than machining and helping a little bit of everything, everything I've ever done to my saws per exact uncle harv teachings have and are amazing machines. Look good buddy good to see ya
Awesome info as always thank you from NZ 🇳🇿 !
Any chance in future of getting a video on Porting a dolmar 9010 ? Seems like a great platform for building a torque monster with the large stroke !
Take it easy man !
If you send him a saw, chances are you won't get it sent back. I highly advise staying away from this crook.
Terrific information Harvey. I was wondering if you could do a total port job from start to finish in a series if you haven't done one already.
Hey Harvey, that saw for tinman sounds like a real ripper, good to see you in the shop moving around
love this man
I’d be really interested to better understand how it all changes when you add reeds into the mix and how that affects blowdown or if at all. The way some pioneers p series are designed almost makes me think they’re made to shorten the blowdown
I will cover this in the next video!
A reed valve motor allows for asymmetric intake timing but doesn't change much else.
The intake can 'open' as soon as there is crankcase depression which would generally be a 'free port' without the reeds.
Prior to reed valves, it was far more common to have a rotary (disc )valve opening directly into crankcase.
It does make motor wider though.
You still have piston controlling transfer timing and exhaust timing
Thank you for sharing your secrets!👍
Thank you Harvey for your expertise in two cycle performance design. I don’t really understand it yet, but I very much appreciate the passion and hard work you put into explaining this to us. I like the whiteboard tutorial someday, as a picture is worth a thousand words. I do like listening to your words so maybe we can get both.
Love the channel Harvey good stuff ❤❤
Hello there Harvey and hello to the saw community I was just wondering if you know of a lighter riste pin that I could use in a Husqvarna 262xp if you could let me know that would be great and eny other recommendations thanks
I do gas rc 1/5 scale engines and I agree with what your putting out …finally some good true tested info on UA-cam thank you ..
☀️❤️🔥🧬🔥Don’t let these jokers get you upset. Hope your well uncle Harvey ☀️🌲🌳
IRONHORSE, do you know what you have made run better for me and my family, you showed me how to live a moral, respectful, high integrity life in gratitude:) You have Blessed me and my family. You made me a better husband, father and man in life. Bless you for that IRONHORSE:)
Love your videos. So I have a 462 with intake and exhaust at 160 degrees..... I'd have to run a piston with lower skirt to get 154° and should I delete base gasket cause that's just gonna Increase the intake? Thanks
Are those numbers the stock timing numbers?
👍🆙Harvey
Harvey I've got a question that nobody seems to be able to answer, maybe somebody can answer it here. I understand the oil gas mix, but how is that delivered to the rotating assembly? How does the bottom end receive its lube to the bearings? I've asked this question on a couple real popular saw channels and have gotten completely different answers. Anybody feel free to chime in?
@@williamwallace9620 are you suggesting that the cylinder and the crank case are hollow and connected in such a way that the mix has a way to reach the rotating assembly and then make its way back into the cylinder? You could be right, I've gotten so many different answers regarding this. thanks for your opinion.
@@williamwallace9620 you did a nice job explaining that,I'll buy it. I'm pretty engine savvy but have never torn a saw down to see how it all jives, thanks again for your time
@@williamwallace9620 solid 10 4!
I’d like to see a longer rod and a gudgeon pin closer to the top of the post too. Same stroke but would be a much stronger combination. Though I don’t know how far you could take it. In the performance V8 world like in your last video, some pins are are so high, they have to make special plugs to support the rings.
However, that could be pushing the envelope way too far for a saw
Thank Y Ironhorse for letting us know bits of your experience and knowledge. The power saw world love Y❤
Please keep making these videos. I feel like I’m finally starting to grasp this stuff. Kinda lol. I am at least starting to get some ah ha moments.
Hi everyone hope everyone is having a blessed day
THANK YOU HARVEY THIS IS JUST IN TIME AND I WILL BE HERE FOR THE NEXT LESSON, THANK YOU
I'm going to be doing a 044 and a 440 this fall. Can't wait to get some good ideas.
That platform likes good intake flow better than anything. It also helps to widen the bottom of the transfer ports. That's what has worked well for me.
🗽🇺🇸💯👌
Hi Harvey ~ I ran into an older (3 year old) Ironhorse video in which you couldn't sleep until you compared the stock jug from a Dolkita 7900 to a bigger top end you had in your shop. We now have a brand spankin' EA7900P here, so I'd really like to learn whether or not that upgrade actually panned out for you? Did you make an additional video about that 7900? I've just liked and subscribed, so please keep up with the fine video work, sir.
Do you think you could do a video talking about finger porting?
Hey, looking to see about having you build one of my saws. Got a ms310 i wanna get hopped up a bit, let me know if you might be interested.
Best treatment for the 310 is to open the muffler a bit, and replace the carb with one from an 044.
On my 372 with a 272 piston I used some of your knowledge I angled my upper transfers up above my popup piston and not to raise the transfer too much It helped. Today I did a experimental muffler mod and it really runs strong now. I agree too much machining can hurt performance like making the combustion chamber small and making the area for the explosion small so there is less area to push on the piston. Which means less power.
If anything, we should be tapering everything opposite to flow direction. To build velocity. That also slows the velocity at which the flow comes back in for the exhaust or out for the intake. Could probably also do that on the transfers.
Good good good.
Thanks Harv!…
Hope you’re doin well!
As always, educational
Love ya buddy! 👍
love it!!!!!!! you do an amazing job!
Hope you’re doing well! Love your channel! Kevin from Bowmansville!
blow out i got plenty ////need a saw to cut HARD wood down here MATE plenty of blow out 😁😁😁😁😁😁😁😁😁
Can you explain all that again 😂. Be good brother 👍
😁😁
Amen! Tell it like it is Harv, no more, no less. The way it's supposed to be.
Hey Ironhorse! I just ordered some parts for my Stihl 660. I ordered a 54mm pop up piston. Would you recommend a gasket delete as well? Would you have went with the big bore?? 🙏
Hey, comment from me
Harvey, that was a short rain that you guys had wasn’t it? Of course, it beats having a gulley washer of a deluge! 😉
thank you for all you do from the heart
Wow this information is now filling in the blanks for this beginner Thank You
Rule number one…. Harv is right and your wrong. Rule number 2. See rule number 1. Ive noticed that high compression saws tend to vibrate more. Have you experienced this? High compression is good and all but after so much your fighting the compression and going backwards arnt ya? Im no professional but i dont care for super high compression saws.
Yer right Kyle! Too much compression and the piston slowes down too much before tdc! And then it fires real hard accelerating the piston! This is where the vibration comes from!
👍
Yeah! Harvey is right and your wrong!!!😂😂😂
Crazy seeing my (almost) wifes name wrote there next to mine
@@travisweldmaster7815 your wife's name is Gabriel ?
@@gabrieltravis6121 gabrielle, gabby, gabbie ect...lol
Long intake duration and too high transfers(not enough blowdown)will use alot of fuel. Also if your upper transfers are poorly shaped you will have short circuiting happening. Long intake creates spitback and wastes fuel. Higher you go on transfers more you will short circuit fresh air fuel charge trough exhaust port and muffler instead of keeping it in the chamber and making power. There is a point when givin the saw more fuel does nothing and if you build work saws you want to have good fuel economy. I dont port for living but its just common sense.
Hey Harvey I sent you a few emails about an 066 that I’m building, haven’t got a response are you still replying to emails? Thank you
😊😊😊😊😊😊👍👍👍🫂🫂🤍
Folks can yap away till the cows come home about blowdown , machining,port shapes, widths , duration ,squish bands , pistons mods , dynos and any number of alterations to enhance the performance of a chainsaw. Imho the modded saw must 1) increase cutting speed, 2) get good mileage and 3) last near as long as a stocker for it to be worth a damn …. A 70cc “built” saw with a sharp chain should be able to pull 1in /sec or better using a 24” bar/chain thru a 21-22” log/round (HARDWOOD not pine or balsa) with larger cc saws maintaining this 1in/sec with longer bars / bigger diameter wood. This is where da rubber meets the road and what separates the wheat from the chaff ! IF the saw cannot pull this 1in/sec (or better) than hit the bricks 🧱 bub. All this 2-stroke theory was worked out 50 YEARS ago by men much smarter than either you or I - These gospel according to masterboob , must be machined / 12 deg of blowdown high compression wondersaws simply cannot pass the 1in / sec standard in REAL HARDWOOD ! They just CANNOT DO IT hee hee hee 😂
Well said!
@@theironhorse6600 thanks Harv , keep up the good work sir
I laugh my ass off everytime I read a comment against a iron horse saw.
@@jerseyjoshua4818 has nothing to do with me so I cld care less that's for anyone that has a issue to deal with. Buckin Billy is a no bullshit tell it like it is guy and watching him run a iron horse saw is all the proof I need as far as build quality. Don't want anything to do with all the other bs drama
Tell them haters that you were doing this stuff when they were sh__ting in diapers.
stealing in diapers?
LMFFAO!!! When us crazy guy’s get older that whole fear of doing life in prison isn’t nearly as scary when you might only have a dozen or so of those left!!! 😂😂😂😂. Those older fella’s shouldn’t be messed around with because they don’t have as much to loose the older they get!!! 😂😂😂. I’m all about 154 and not more then 156… but I just can’t really do anything without see my port mapping and actually seeing the engine!!! I just love when you are feeling scrappy brother!!! LMFFAO!!! I’m an old redneck boy so a good scrap is always fun! 😂😂😂. You’ve helped a whole bunch of guy’s build them a really decent work saw and they didn’t have a lathe and they have a strong runner! And obviously if a guy has a lathe he’s going to be able to get a stronger engine if he’s doing it right! Just cutting the popup into the taller pistons is the huge benefit as well as trimming the base’s!!!
Great video Harvey! Nothing but love for ya brother!!!
😲🦴