Great mechanic and welding skills but it seems like this is a lot of work for such a small chipper. Wouldn’t it have been better to make it about three times the size to handle large diameter branches?
I don’t think this will work - it will probably need a shelf with blade to provide a space for the chips to shear. Otherwise it will jam! Unless you show otherwise. P.s please don’t take your shirt off again!
Saludos al amigo de Cypsmen el video esta muy bueno lo unico mal que encontre es tu seguridad usando la pulidora sin proteccion para tu nariz te recuerdo de que los pulmons no se venden en la ferreteria o en la farmacia pero el equipo para protejerte si cuidate. Te hablo por experiencia de mi padre el soldaba usaba la pulidora etc y sin proteccion para su nariz y murio victima de una enfisema pulmonar , una enfermedad muy triste sus ultimos dias los paso pegado a una maquina oxigenadora. Su mejor mensaje fue bien claro antes de morir y nunca lo e olvidado me dijo al usar maquinaria y bregar con cosas toxicas , fiberglas etc cuidate y proteje tanto tu vista como tus pulmones.
wanted to see more. like what powers it and how is it affixed to whatever you are putting it in or on. like it is it is just a box with a fancy spinning shaft and blades. looked for link to part two but did not find one. because of that i have to give this video an incomplete.
When you cut the center hole for the bearing plate you could have used a holesaw in the drill press or chucked the plate in the lathe useing the 4 mounting holes.
Wood Chipper with 1 shaft are not really good. Just because it can cut about 2-3 cm based on wood density. Wood Chipper with 2 shafts are really better. Can cut much more, up to 6-8 cm
Just 2 bolts per blade? you need more! Those bolts will snap, theres tremendious forces involved in a Wood chipper. Would suggest at least 4 bolts per blade.
Hey man you did a good job on this. Why did you go for narrow design with long blades and not the drum design with staggered blades? I don’t have the eqiptnent to work on sheet thicker than 1/4” so have too gone with this arrangement but a little smaller, using pillow blocks rather than flange bearings for ease of adjusting cutting height. It seems all the drum designs are direct drive off motor.
Na ja, Löcher bohren um danach trotzdem mit den Winkelschleifer auszuschneiden, Acetylen Brenner kann man auch als Plasmaschneider benutzen, und ob das Zeug funktioniert wissen wir auch nicht. Maximaler Zeitverlust.
Should have done your welding without a shirt. I found that wearing only a t-shirt leaves tan lines on the upper part of the arms after the radiation burn heals.
What was that ,that you used for the blades? I need one of these to chew up sawmill slabs. I have some half inch x 4 inch mild steel bar stock that I thought about making the blades from but I'm afraid mild steel will bend at the cutting edge.
надеюсь вторая версия уже была с ножами под углом30-40 градусов , вместо 90 градусов на валу. в таком положении ножи будут принимать удары на плоскость а не на острие.не работай без перчаток.
why did you cut out the center with a grinder after you drilled the four holes why not skip the four holes and cut out the center with the grinder ????
I think it will jamb as there is no shear plate. Plus depth of cut is extreme with no feed control. We need to see further how this performed. Its not how chippers are normally made.
Masakra 😮 Tam BHP to nie istniało,takie wiertło by mogło dużo krzywdy narobić...dobrze że ci nie obruciło i łap nie pocieło,śruby zamiast wzmacniane to zwykłe i to bez podkładek sprężynowych he i jeszcze to trasowanie pod otwory......oś zmierzona na pałe🤦
Holy Moses. Those blades mean business; I Cant wait to see em in action
Can you do a small one that can run on 240v for a home workshop
What do you attach this to? Electric engine by belt? Gasoline engine hooked to shaft?
Ciao volevo sapere se questo rotore di taglio è in vendita. Quanto costerebbe? Grazie!
Great mechanic and welding skills but it seems like this is a lot of work for such a small chipper. Wouldn’t it have been better to make it about three times the size to handle large diameter branches?
I want see it in use.
I don’t think this will work - it will probably need a shelf with blade to provide a space for the chips to shear. Otherwise it will jam!
Unless you show otherwise.
P.s please don’t take your shirt off again!
Sunteți extraordinari
Saludos al amigo de Cypsmen el video esta muy bueno lo unico mal que encontre es tu seguridad usando la pulidora sin proteccion para tu nariz te recuerdo de que los pulmons no se venden en la ferreteria o en la farmacia pero el equipo para protejerte si cuidate. Te hablo por experiencia de mi padre el soldaba usaba la pulidora etc y sin proteccion para su nariz y murio victima de una enfisema pulmonar , una enfermedad muy triste sus ultimos dias los paso pegado a una maquina oxigenadora. Su mejor mensaje fue bien claro antes de morir y nunca lo e olvidado me dijo al usar maquinaria y bregar con cosas toxicas , fiberglas etc cuidate y proteje tanto tu vista como tus pulmones.
wanted to see more. like what powers it and how is it affixed to whatever you are putting it in or on.
like it is it is just a box with a fancy spinning shaft and blades. looked for link to part two but did not find one.
because of that i have to give this video an incomplete.
Ugye fogalmad sincs a szerszámok használatáról?
When you cut the center hole for the bearing plate you could have used a holesaw in the drill press or chucked the plate in the lathe useing the 4 mounting holes.
Whats the size of the square middle shaft
The size of the square shaft on which the cutting knives are mounted is 3.5 cm wide, 3.5 cm high, and 12 cm long.
Greetings.
Wood Chipper with 1 shaft are not really good. Just because it can cut about 2-3 cm based on wood density. Wood Chipper with 2 shafts are really better. Can cut much more, up to 6-8 cm
How do the 2 shaft ones work?
сначала сверлил, потом болгаркой обрезал и в итоге выяснилось что есть ацетиленовая горелка. Вопрос А сразу горелкой вырезать не смог?
Горелка предназначена для пайки или сварки! Для резки используют резак!ЭТО РАЗНЫЕ ИНСТРУМЕНТЫ!¡!!!!!!
Иначе видеоролик коротким получится.
Just 2 bolts per blade? you need more! Those bolts will snap, theres tremendious forces involved in a Wood chipper. Would suggest at least 4 bolts per blade.
Hey man you did a good job on this. Why did you go for narrow design with long blades and not the drum design with staggered blades? I don’t have the eqiptnent to work on sheet thicker than 1/4” so have too gone with this arrangement but a little smaller, using pillow blocks rather than flange bearings for ease of adjusting cutting height. It seems all the drum designs are direct drive off motor.
you look great
Home made?
workout schedule. you are pretty shredded.
let us see this thing working
Jaki odstęp noża jest od podłoża gdzie będzie przecinana gałąź? Z góry dzięki 😉
Jeżeli to możliwe to odstęp powinien być jak najmniejszy. Pozdrawiam.
W profesjonalnych rębakach 0.2 mm
Please don't wear gloves or loose clothing around rotating machinery. That is an excellent way to lose a body part.
Hello, what are the dimensions of the blade?
Good work. thanks
Congratulations on your work. I would like to know if I can buy a wood chipper. Thanks!
Na ja, Löcher bohren um danach trotzdem mit den Winkelschleifer auszuschneiden, Acetylen Brenner kann man auch als Plasmaschneider benutzen, und ob das Zeug funktioniert wissen wir auch nicht. Maximaler Zeitverlust.
Should have done your welding without a shirt. I found that wearing only a t-shirt leaves tan lines on the upper part of the arms after the radiation burn heals.
E possibile sapere le misure ???
What was that ,that you used for the blades? I need one of these to chew up sawmill slabs. I have some half inch x 4 inch mild steel bar stock that I thought about making the blades from but I'm afraid mild steel will bend at the cutting edge.
i think it was a leaf spring
где практическое применение этой поделки? Или это, чтобы было, на полке для поделок?
Виктор Малыгин это главная деталь в измельчителе веток на дрова! Отличная штука с бензиновым движком!
Hey mate, where did you source the center axle piece?
lathe
un procedimiento para un buen uso, Me darias las midas ( gracias.)
All that great work snd you didn’t show us in operation????????????????
надеюсь вторая версия уже была с ножами под углом30-40 градусов , вместо 90 градусов на валу. в таком положении ножи будут принимать удары на плоскость а не на острие.не работай без перчаток.
Forgot the keyway in the shaft. blades stick too far which increases vibration.
please make a video, how its works!?
Yes the proof of the pudding. . . . . . . . I notice you put your shirt on before welding!
Супер! Молодец!
why did you cut out the center with a grinder after you drilled the four holes why not skip the four holes and cut out the center with the grinder ????
I had thick steel and later it was easier for me to cut off the middle, grinder is not a laser.
holes did not have to be square, just cut them out with hole saw. lots cleaner and quicker
I think it will jamb as there is no shear plate. Plus depth of cut is extreme with no feed control. We need to see further how this performed. Its not how chippers are normally made.
Para que sirve eso???
Para moler que??
Great ! Good job !
Szia.működéséről nincs video?hogy dolgozik?
Szabolcs Kun van róla videó
Radziłbym zrobić mocowanie noża na 3 śruby.
Según tu q cargada isistes
Не сверлите заготовку держа ее в руках! у меня как то вырвало из рук при таком сверлении, разбило пальцы до кости
на уроках труда в школе видел как однокласнику пальцы распарола когда сверло закусило....Та и поделка вышла непрактичной по факту у автора
Θρυματιστης κλαδιον τσουντανης
Moze neki kontakt
That darn music just ruin's an otherwise good video...
Death machine waiting to be powered up. (see video #3)
Para que sirve esa herramienta
Super
ลองเครื่อง ..ให้ดู ด้วย ครับ นายช่าง 😅😅😅
Good Luck
А тест драйв чё не удался? Зажевало ветки ?
Plans? Anybody?
cuanto esta molino de granos
Hello... Can you send me the sketchup project please ? Thank you for advance
Я вот думаю почему у нас напряженка? Просто там левшей судя по сварке, сколько у нас правшей, руки пожимать не получается.
Мне кажется или на самом деле нож один не той стороной стоит
Tuyệt vời quá
Para que sirve
Dude use the vise
Good thing u took ur shirt off. Now everybody knows u work out
Membuatnya beneran.
Sayangnya tidak diuji kerja.
а в работе
Y que hace esto ?
julio vera picar ramas y hojas de árboles
this is no home made. no regular home has that kind of equipment.
Ai bombado gostei do seu trambalho bastante extrovertido parabéns. manda um alo ai, te dei um joia,e vou me inscrever no seu canal Manaus AM brasil
Met des gants quand tu soudes
9 minutes of "2x playback just isn't fast enough"
Pero que hace
Masakra 😮
Tam BHP to nie istniało,takie wiertło by mogło dużo krzywdy narobić...dobrze że ci nie obruciło i łap nie pocieło,śruby zamiast wzmacniane to zwykłe i to bez podkładek sprężynowych he i jeszcze to trasowanie pod otwory......oś zmierzona na pałe🤦
you don't wanna show us that it won't wo.. .
Oye donde comprastes esa mascara para soldar .. jajajajajajajaaj
(╬ಠ益ಠ) You can’t even fit a human skull in it, pointless!
Что это?
Kardeş bundan banada yaprmısın
Nobody is interested in how quick you work or fast forward. Useles video without measurements and parts specs.
Инструмент есть-ума нет.
facet nie pokazuje tego co jest istotne :/
too much side clearance
Зачем большие отверстия сверлил?
Won't work.
Tasheer Alam
Х
Me gusta el pico y era
My husband used these plans from woodprix and he's very satisfied. However. I love Yours !
Haha, a twig chipper, maybe?
вот продолжение ua-cam.com/video/VG-BLf7yOrQ/v-deo.html
Aaarg me eyes
???
Jesus fucking title screen...
What music!!👿