Це відео не доступне.
Перепрошуємо.
How to Fix Dead Electric Skateboard Batteries!
Вставка
- Опубліковано 13 сер 2020
- If your battery charger does not charge your electric skateboard, it may be because your battery voltage is way below 0%. You can easily fix this by using a lower voltage charger until your regular charger works on it.
Just wanted to stop by and tell you that this worked on my evolve bamboo that had a dead battery. I stuck on a charger to a vacuum cleaner for a few mins and then stuck on the original charger and now it's charging. Thanks a lot bro!
Hello I have the same problem, can you tell me how you connected it thnks
@@nelsonbonaki2345 I just took an old power plug that was lying around the house that had the same sized plug as the original charger. I just plugged it in for like 10 minutes then I unplugged the non official one and plugged in the official charger and the light started blinking indicating that it was charging again.
@@wetokebitcoins1769 Thanks, I was wondering why no charger has the battery output for my skateboard model (GTR), I guess your model is the GT?
Thanks for the info guys! I'm hoping my board will come back to life again. I've got it on a Dyson vacuum charger right now 😄
I recently got my first board ever and its battery was basically dead on arrival and the company I bought it from had gone bankrupt so it's been a pretty frustrating experience, but this gives me hope
I have a smaller boarder that uses a 29.4 volt charger and it isn't charging likely because it's way below zero, I get some blinking and beeping when I push the power button but that's it! What voltage do you recommend I try to see if I can being her back to life?
If you don't have a charger you can flip a bike upside-down mesh the wheel with a motor and crank the petals, so this for around 5-10 minutes untill it turns on. Spinning it like that generates power and charges your skateboard. I just did it
Did that for my board but it still can't charge
From my understanding, the board has to be powered on for regenerative breaking to be functional.
I think I would get amazingly fit trying to do that with my board. My batteries have almost completely discharged so I would be severely cranked off with myself if I ever tried to learn your skateboard trick
Same. Bustin magneto hybrid @@walter8758
If there is water damage is it the ESC that would be the problem, the battery or both?
Bro could you hook me up with the link for the 36v charger you got? I think that will work with my Vestar Blackhawk; your board looks almost exactly like it.
Can I get my dead battery up with a 9v charger?
Thank you very much for the info
Hey i have an issue with my electric skateboard. it only works when the charger is plugged in and when i unplug the charger and pressing on the start button on the skateboard it won't light up. why is that? how to fix that?
I have an Evolve GT that won’t charge. My charger is a 42v/2A charger and stays green when plugged in. The battery has 10 cells and each reads roughly 4050mV. The total voltage of the pack is 40.952v with a current of .012A. I’d like to try your smaller voltage charger trick but when I look for chargers to purchase for 36v they all state they’re 42v/2A chargers. What do I purchase? Need help
Yo I have a 36v 5.8 brand new right out of the box it won’t hold a charge at all I have a 12v charger on it now but I don’t think it’s working maybe dead cells what are my options on upgrading the battery for better range and distance
Hey man I got a question for you maybe you can help me out I'd really appreciate it. I have a battery pack that charges normally but then when I ride it for a coupe of kilometers it will just die all of a sudden. It shows the charge as full initially and then once I reach like 80%, it shuts right off and it will not turn back on? Do you know what might be the problem? Or maybe you can point me to one of your videos to see how I can test or what to test? Thanks Dr.E!
Seems like one of your P group might have a loose connection or a bad cell. So its draining faster then the other p group. BMS will shut it off when it detect it at a certain voltage.
@@619Mylife thank you ! I think I'll just upgrade to a larger battery pack. I wanted to upgrade anyway.
So I have a weirder problem
I didn’t use my electric skateboard in a long time and yesterday I wanted to go again and at first it didn’t want to charge but after a few moments it did
Then I went but when I was riding it randomly turned it multiple times and now today it doesn’t wanna charge anymore do you know the problem?
what charger do you suggest for the inboard m1 battery that has gone sleep or dead from inactivity? Also how to open a inboard m1 battery without breaking it?
My board charges but when i try using the board the battery loses all juice until plugged back into the charger then works for acouple seconds only to keep shutting off
Yes yes this is me just now with my first e skateboard I just got. Works for a minute, turns off then won't turn on again unless I plug it into the outlet just to turn it on. Idk I'll try charge it overnight I guess even though it shows it's fully charged
I Have a Exway X1 max and it won't charge period ! and it's only at 29 % but good to know this
Thanks for sharing the great video. I have an arc board I got used but it won't charge. Original fast charger output is 38V 3amp. I plugged in a notebook charger, output 16V 3.75amps, but even after 8 hours the charger is not warm at all. Any idea of what could be wrong? BTW, the motor runs with the battery level light in the red.
Quick question hopefully you can help me out. I have the backfire G3 like new only rated like 10 times bought it last summer. When I put it up for winner, it was on a food charge and then when it was time to write it, it was dead so I charged it and it charged and turned the green light on in 10 minutes then the next day it was dead. Please help.
Hi I have a skatebolt breeze 2 my battery is 4 month old Samsung 18650 10s2p when I conect cthe charger is 42 volts show green that means battery is full but won't start skateboard and the output voltage on my skateboard battery show 16v only if I plug charger shows 42 and I can start skateboard. should I apply your method or something different because battery is full charge. please help
Did you manage to solve it ?
My board just died out of no were and won’t charge what can I do???
I have Ownboard AT like yours. I left it for 2 months without charging it. Obviously now the main charger, when plugged to the board, stays with the green light on and this means that isn't charging. Did this happen to your AT as well? If yes, did you sort out the problem in they you said in the video? Thank you
This is a faulty bms, battery pack is fine. I will have a video on bms replacement soon.
@@dr.eskateboard3381 don't you think is the same problem you had? (What showed in the video)
Yes I thought it was just bms discharge but later found out it was bad bms or bms that went bad, this seems to be a widespread case for ownboards.
It does this happen only when the battery discharge by itself completely? Because the board is new, I've only used it for 3 months and about 6 weeks without using it.
What if my battery won't charge past 50 percent? Dead cells?
Very important question my board doesn't charge I meant it changed but doesn't fill it . Exway flex. What should I use as a charger
So it charged but not 100%? Keep power cycling, basically ride to 50% then recharge to 100%. Batteries probably not balanced then it wont charge to 100%.
Do you ever do giveaways or anything like that
I have a Halo Board carbon edition. Brand new but has not been used for 3 years. It was shipped by sea and arrived this week. Life, work, and travel restrictions eg coronavirus meant that I ended up settling in the UK. The manufacturers will not provide any support to attempt a repair myself. Their reason for not helping is that I'm no longer living in the US. I think a more honest answer would have been that they do not want to give any time on this. Thank you for your video. I would appreciate any advice that you can give eg anything I definitely should not do?
I took the top off and disconnected the battery to test its voltage with a multimeter. That gives a reading of 1.889V. The label on the battery says 6.6AH (capacity) and 36V (standard voltage). I've ordered a 2.1mmx5.5mm 12V DC Male Jack to Alligator Clip power cable connectors. Its usually used for CCTV security camera lighting but in my case I will connect it to a 200W adjustable power supply (PS201ADJT). I can only adjust the output between 5 to 15V and current limit 0 to 15A. I might have to build something to get it down to a voltage low enough to charge the battery. Any help or advice would be appreciated. I've never attempted anything like this on a lithium ion battery before. I'm likely going to have to build an LM317 voltage regulator to get this battery working again.
If anyone has to attempt something like this possibly due to very bad technical support from their skateboard manufacturer here is a useful video to build a voltage regulator. If you are in the US all of the parts can be purchased easily.
ua-cam.com/video/IjJWWGPjc-w/v-deo.html
Also found this on amazon www.amazon.co.uk/Charger-Digital-Balance-Discharger-Batteries/dp/B07LG21Z3P/ref=asc_df_B07LG21Z3P might be useful for other repair projects
Bad bms is very common also, you can try this ua-cam.com/video/rw9EYVSWaz0/v-deo.html
@@dr.eskateboard3381 Thanks, your forum link doesn't work. Can I email you Lee?
what charger does anyone suggest for the voyager neutrino?
Idk if you still check comments but I have a wowgo 3x that suddenly stopped working and only turns on when plugged in could you try and help me?
My problem is the board quit running. Battery is nearly at full capacity and won't power back up. It suddenly quit while riding. Remote also shows full charge but pulse vibrates indicating disconnection from board. Even tried pushing and holding power button with pen to make connection. Still nothing
Same problem here
Can someone please share a link to the correct volt charger that would work for my board? He shows a close up of the 42 volt charger, but that is not helpful. I need specs for a lithium battery 10s5p 18650 36v, 10ah, 360 Wh. I'm assuming, based on this video, that I would need a charger that is lower than 36 volts, which would probably be a 7s 29.4v 1.5 A. I just want to be sure before purchasing. Thank you for your help!
I have the same battery in my off road board. It charges enough for 5 seconds of riding and then totally dies . I can't even find a replacement battery so I don't know what to do next.
wonder if this works for the boosted RLOD issue.
Thank you
This looks like a fire in the making LOL
Hi maybe you can help me out my board is won't charge when I plug the charger is still show green light is not change to red any idea(maybe the charger died) beacuse I let to sit my board for 8 months when I charge is charge up and after I use like 5 mins to see is ok and then that's it thanks your help
Have you ever found a fix?
I have a Lycaon board GR 2020 and the charger stays green so it’s telling me it’s fully charged. I turn on the remote then sync it and then immediately dies. Does anyone know what that might be?
I have the same problem with my Swift, what did you end up doing?
Recently got my first board. Died after 4 minutes. Tried returning but company went bankrupt. Tried this trick with some old chargers I found but no dice. This hobby sucks lol! Guess I will have to get custom battery from somewhere....
I have a Ownboard Bamboo battery that won’t charge beyond 60%
Will this work for a koowheel
Possibly.
my board has a 42 volt charger, what do you recommend 36v or any thing lower is fine???
I would actually recommend adjustable bench power supply, then you can dial in any voltage you want. Get a 60v power supply so you can do 0 to 60v.
you are cracked and you help alot! :)
Hey dude, I just got my Ownboard AT1W and it has pretty much the problem you're saying. Charger won't change light and whenever I charge it for hours, it turns off super fast. You believe even in the case of a brand new board it's worth trying it?
I am gonna figure out how to fix it or maybe just replace the ESC. It seems Hobbywing esc likes to die. Even my Vestar is dead.
You actually believe swapping the esc might help? I might just unplug everything, plug it back in and see if it helps somehow
You need to try measuring voltage of battery first. If battery is at 42v at full charge it's not the battery but if battery voltage 36v or below and not charging it's your battery that's dead.
@@dr.eskateboard3381 Thank you so much for your help, take my sub ;)
Two minutes of information explained five times. Thank you, anyway.
BRO I WATCH YOU VIDEOS THEY ARE GREAT I NEED SOME HELP WITH MY EVOLVE 2ND GEN BAMBOO ALL TERRAIN I CANT SEEM TO GET A CHARGE GOING ON MY BATTERY
Try opening up board and measure the battery pack with battery terminals disconnected first. If near 40v your battery pack is fine and probably bad bms or esc.
My evolve battery is putting out 19 volts and the 42v charger won’t charge it. What do you recommend?
Did you ever figure this out? I’m having the same problem.
hi can you help to fix my skateboard?
Sure what's the problem?