Thank you so much for very understandable videó sir! That "turn to clockwise to loose" screw made a full sunday of headache for me. You made my happy :) Thank you again and I wish you good health! Greatings from Hungary
If anyone is going to do this, I strongly advise you replace the tone ring while you are at it. That is the press fit steel piece with the dozens of little rectangular cutouts around the outside. This is what the wheel speed sensor for the ABS brakes uses to measure axle speed.
Thanks for the video. Really good information. Question: If I did not have a press to put the bearing back on, I reverse your technique of removing it?
I personally would NOT try that. If you were to do it that way, it would be putting pressure on the outside of the bearing. That could possibly break the bearings out of their housing.. That is why I suggest pressing the inside part of the bearing. That way there is no pressure on the outside housing.
great video, I have the same seal leak why did you remove(hammer on) the sheet metal holding the seal? replacement kit I got doesn't include the metal part only the thick rubber seal
What us peasants who don't have a slide-hammer bearing puller yokie do is put 2 over-long bolts into the stud holes & wind the sucker off using those & an impact gun.
Thanks very much sir. I'm not very good in English but you speak slow and I can enderstand. Thanks a lot, God bless you. I'm from Madagascar.
Thank you so much for very understandable videó sir!
That "turn to clockwise to loose" screw made a full sunday of headache for me.
You made my happy :)
Thank you again and I wish you good health!
Greatings from Hungary
If anyone is going to do this, I strongly advise you replace the tone ring while you are at it. That is the press fit steel piece with the dozens of little rectangular cutouts around the outside. This is what the wheel speed sensor for the ABS brakes uses to measure axle speed.
На подшипнике нужно удалить внутренний пыльник чтобы к нему поступала смазка.
this is a really cool technique to remove the bearing (Y)
Привет дядя у меня тоже такой DODG SPRINTER только жёлтый завтра пойду менять кожух тормозного диск ка с колодками видео понравилось всё понял. Ok😊
thanks for a great video
Thanks for the video. Really good information. Question: If I did not have a press to put the bearing back on, I reverse your technique of removing it?
I personally would NOT try that. If you were to do it that way, it would be putting pressure on the outside of the bearing. That could possibly break the bearings out of their housing.. That is why I suggest pressing the inside part of the bearing. That way there is no pressure on the outside housing.
nice work
great video, I have the same seal leak
why did you remove(hammer on) the sheet metal holding the seal?
replacement kit I got doesn't include the metal part only the thick rubber seal
I am not real sure what you mean. The seal that I replaced has the metal ring and rubber gasket all one piece.
Priceless....
What us peasants who don't have a slide-hammer bearing puller yokie do is put 2 over-long bolts into the stud holes & wind the sucker off using those & an impact gun.
What’s your trick for pressing the bearing into place?
Отрезок трубы подходящего диаметра
А гребёнку можно менять?
Здравствуйте. Номер, размер гаечного ключа который затягивает гайку подшипника скажите!
I bought my tool on eBay. Please search eBay for this description. (FIT MERCEDES SPRINTER REAR AXLE LOCK NUT SPANNER WRENCH TOOL FITS 9023570126 NUT)
Hit it with a punch to tighten it lol
why 2 splined areas near the diff?
I have no idea. I saw other video's that state they have no idea either. Good Question.
В этих мостах ставят блокировочные втулки ,для полной блокировки моста !
Probably something to do with lubrication.
The rear diff lock (if you have one) engages with those outer splines
Good info for how to replace backing plate on 2004 sprinters too.
Actually, that is what I was doing. Thanks for watching!!