How To Replace Control Board // MINN KOTA POWERDRIVE

Learn how to replace the control board on your Minn Kota PowerDrive.
Whether you have a PowerDrive V1, V2 or Bluetooth Model.
Our step by step guide will help you identify and replace your board.
POWERDRIVE CONTROL BOARDS
Minn Kota PowerDrive Control Board (12 Volt - No AutoPilot)(2884055)
trollingmotorp...
Minn Kota PowerDrive Control Board (24 Volt - No AutoPilot)(2884056)
trollingmotorp...
Minn Kota PowerDrive Control Board (12 Volt - AutoPilot)(2884057)
trollingmotorp...
Minn Kota PowerDrive Control Board (24 Volt - AutoPilot)(2884058)
trollingmotorp...
The repair in the video was done on a Minn Kota PowerDrive V1 Model.
The control board used was part number 2884055.
Adding Advanced GPS to your Minn Kota PowerDrive? WATCH THIS:
• How To Install Advance...
Adding I-Pilot to your Minn Kota PowerDrive? WATCH THIS:
• Minn Kota PowerDrive V...
Check out our channel for other Quick Tips, Repairs and Reviews.
Thanks for Watching!
If this video was helpful, remember to give it a like and please consider subscribing!
**New videos coming soon on other repairs, maintenance and tips**
Disclaimer:
Due to factors beyond the control of TrollingMotorParts.com,
We cannot guarantee against improper use or unauthorized modifications of this information. TrollingMotorParts.com assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. TrollingMotorParts.com recommends safe practices when working on motors, boats, wiring and or with tools seen or implied in this video. Due to factors beyond the control of TrollingMotorParts.com, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result.
All do-it-yourself projects entail some risk, it is the sole responsibility of the viewer to assume this risk.
Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not TrollingMotorParts.com.
#trollingmotor #powerdrive #minnkota

[@ChadCunningham-n7j]

Can you provide more details on what is needed to make a V1 unit operational after installing a V2 board? I didn’t know the foot pedal would need replaced? Mine has the copilot installed. What are the issues with the copilot and operating phobe? Your information is very helpful and is done well. Thanks

[@devonplant6742]

You will need the remote or the foot pedal for the v2. Your V1 pedal will be useless after the upgrade.

[@VizXRyRy]

The obvious question is, if I were to put this v2 board into my v1 Powerdrive, would that allow me to add the Copilot or iPilot accessories?

[@notsogood6249]

I learn so much from your video's. Have you ever done a video on where you should keep your trolling motor clean or lubricated? I have a 24V Fortex 80 lbs. on my bass boat and I just look for moving parts to keep clean and lubricated. I'm not sure if this is correct.

[@RichardDanielson-i2q]

I have a 80 thrust min Kota it just started acting up it goes forward and reverse but as soon as you try to increase your power it stops forward and reverse do you have any idea what the problem my be. It is a 24volt motor the voltage gauge shows plenty of power.any suggestions would be helpful.thank you very much 👍😎

[@damonellison8112]

I have a v1 power drive with a serial number starting with mkaf. Can I replace the control board?

[@conniedarnell3517]

Do you have a phone #?