Hello sir. I want to adjust mine like that. Will a factory hammer spring open the valve .? Or i will need to change the factory hamer spring? I mean is it srtong enough to open 200 bar reg?!! Or you did not change the hammer spring . Thank you sir
@@truthspeaker2062 we made our own upgrade upgrade kits which include the hammer spring available at www.africanairordnance.com/424820687#!/airgun-technology/products/2023-upgrade-kit-gen-2-for-vulcan-3
I have the same rifle, but the air cylinder was accidentally emptied, and the rifle is in a cocked state. The problem now is that there's a gas leak from the barrel when I refill the gas. What is the solution to this problem?
U have to remove the bottle then remove the front block that the bottle screws into then remove the front block from the plenum tube if you shine a light into the front block on the plenum side of the block way in the back you will see a Tiney Allen screw you will need a very long Allen key to reach it that screw holds a small Oring in place this Oring is what keeps the HPA from leaking back out once you bleed off to disconnect if it comes loose then it will let air leak out you just need to tighten it down
The plenum has tiny breather holes on each end of the tube. This means if you have the reg on one side you plenum will be smaller and less powerful if you the flip the plenum over and install the reg on the other side you would greatly increase the volume of the regulated area this would greatly increase the power of the rifle I can't give u the depth of how far the reg sits inside the plenum
Jeremy, this is a great tutorial, thanks for sharing your indepth knowledge of this wonderful pcp! My brand new .22 V3-700 with a factory depinger is quite loud at the cheek rest! Is it normal, wondering if it's suppose to settle down once I shoot it several hundred rounds? Thanks... Eddie-Eduardo
Thank you I don't think its a matter of settling down As the ping is coming from High Pressure Air moving at a high velocity through the plenum, a depinger works by slowing the air moving through the plenum in a similar fashion to a baffle in a suppressor. I don't see how after 700 shots the HPA will change how it flows through the Plenum.
What about the hammer spring I did adjust mine about 1/4 turn counter clockwise and I didn’t get much different velocity even with hummer springs at max. Can you give us some info about the spring and hummer I think my spring is too weak or something
A question please, by turning the regulator, do you know how much you earn approximately, thanks I forgot that the use of an added suppressor is appreciated. He has thrown slug boat tail with it, no more.
Hello again, regarding the regulator. What is the reg pressure set at in this video? Is it a spring type or washer type? Does the manufacturer of the rifle make the reg or is it bought 3rd party and if so, what is the brand of the reg ? At this stage, have you already changed the hammer spring to achieve these velocities?
@@AfricanAirOrdnance Interesting! The Reg has no spring or washers? How about doing a special video on the Reg design? That way we can see how it actually works. Many thanks
I contacted AGT about the max recommended reg pressure and they said it shouldn’t be set above 170 bar. Have you modified the reg so that it can withstand 220 bar? Or did you mean that 220 bar was the bottle pressure?
He will only show you regulator modifications and simple stuff. The hammers srping mods or any other mods in order to been able to work on 220 bars he will not tell you. Not very helpfull other than showing your gun shooting with a lot of power but that is all
They say that this vulkan is just so much better than the fx impact 3 despite all the hype and marketing bullshit of the latter. Thanks for making up my mind.!!
I've just watched your video again and you are getting great power with very good accuracy but at 220 BAR I'm amazed you are not suffering valve lock. Are you 100% sure the plenum pressure is working at 220 BAR? BTW, are there any proper schematics of this gun?
I know you mentioned that you were not trying to shoot groups, rather trying to check velocity. But how does the gun group at those speeds. The groups you shot were average for that gun. Thabks
Actually the groups in the first part of the video were much bigger at lower speed and got tighter with the increase obviously finding ammo that the gun likes is also very important again as I did state I wasn't shooting for Super tight groups but to get a 40 gn slug over 1000fps and the numbers were extremely consistent for that power output The bigger slugs 40 gn and 45 ,gn are designed for higher speed Old school Airgunners rule of thumb used to be for Airguns keeping your slug under 1000 fps was best for accuracy in pellets that is true but slugs things are changing fast
@@AfricanAirOrdnance thx for that bud! Would u make a video shooting those slugs and try to get them to group sub MOA. I have a few AGT Vulcans/Uragans from .177 to .762 and was just about to press the button on the Vulcan 3. Love the polygonal barrel on it but can’t seem to find any evidence on whether it can really shoot slugs sub MOA with minimal tinkering. Thx again
Thanks for the video.. very well done... the next step I'd love to see done... is the step to get very tight groups... seems to be every gets the tutorial to this point and won't go any further.. so is the next step to up speed a little more at a time to see what happens with accuracy?? And what would you recommend a safe speed for the rifle...any info we may need on hammer spring adjustments??? Does it need adjusting? Or should we just stay with reg pressures...it's just feels like we as newbys to the slug club are only getting half the story all of the time.... OK yes you need a slug the gun likes... but show us how it all goes for first shot and all the tuning to get to crazy groups at 100m
What is the working pressure after changing the regulator?
Amazing, have changed the hammer spring? And how much is the reg pressure?
?
Thank you for the informative video. Looking forward to the next one 😉
Nice video on pressure adjustment. Question: Is there a reason why your not loading up the mags and loading one at a time?
Slugs to long for standard mag
@@AfricanAirOrdnance Rubbish design. Did they really expect pellets to be accurate at 70ft/lb?
Hello sir. I want to adjust mine like that. Will a factory hammer spring open the valve .? Or i will need to change the factory hamer spring? I mean is it srtong enough to open 200 bar reg?!! Or you did not change the hammer spring . Thank you sir
thank you for watching you will need to replace the factory hammer spring
@AfricanAirOrdnance thank you for your reply sir. So which spring will fit .
@@truthspeaker2062 we made our own upgrade upgrade kits which include the hammer spring available at
www.africanairordnance.com/424820687#!/airgun-technology/products/2023-upgrade-kit-gen-2-for-vulcan-3
شكرا جزيلا على الفيديو الجميل
كم رفعت ضغط المنظم لو سمحت ؟
Thanks for watching 60 bar
Beautiful video and clear enough
Glad you think so! thanks for watching
THANK YOU!! Awesome! I just love my Vulcan 3.. and now gonna up the reg just a bit😁
Adjust in small amounts
How many shot you get with your velocity?
Seriously, not able to adjust reg pressure from outside?
I have the same rifle, but the air cylinder was accidentally emptied, and the rifle is in a cocked state. The problem now is that there's a gas leak from the barrel when I refill the gas. What is the solution to this problem?
U have to remove the bottle then remove the front block that the bottle screws into then remove the front block from the plenum tube if you shine a light into the front block on the plenum side of the block way in the back you will see a Tiney Allen screw you will need a very long Allen key to reach it that screw holds a small Oring in place this Oring is what keeps the HPA from leaking back out once you bleed off to disconnect if it comes loose then it will let air leak out you just need to tighten it down
Greetings to you, sir. I have a question. Please answer. What are the dimensions of the receiver? Length, width and height please
@@markjonior contact Airgun Technology who manufacture the rifle they could give you that info
Thanks for watching
Great informative video…my question is, how far in does the regulator sit inside the plenum? Is there any indication? TIA
The plenum has tiny breather holes on each end of the tube. This means if you have the reg on one side you plenum will be smaller and less powerful if you the flip the plenum over and install the reg on the other side you would greatly increase the volume of the regulated area this would greatly increase the power of the rifle I can't give u the depth of how far the reg sits inside the plenum
Wait, you have to completely drain the bottle, and dissasemble the rifle to adjust the regulator? I THOUGHT I wanted a Vulcan 3 until I saw this.
Yes you do
Jeremy, this is a great tutorial, thanks for sharing your indepth knowledge of this wonderful pcp! My brand new .22 V3-700 with a factory depinger is quite loud at the cheek rest! Is it normal, wondering if it's suppose to settle down once I shoot it several hundred rounds? Thanks...
Eddie-Eduardo
Thank you I don't think its a matter of settling down As the ping is coming from High Pressure Air moving at a high velocity through the plenum, a depinger works by slowing the air moving through the plenum in a similar fashion to a baffle in a suppressor. I don't see how after 700 shots the HPA will change how it flows through the Plenum.
@@AfricanAirOrdnance OK, thanks👋
Nice shooting. 45 good groop. What the distance
85 yards
What about the hammer spring I did adjust mine about 1/4 turn counter clockwise and I didn’t get much different velocity even with hummer springs at max. Can you give us some info about the spring and hummer I think my spring is too weak or something
Definitely find a stronger spring we will be putting out a Upgrade kit in the next 8 weeks that will include new hammer springs and some other parts
Hi
I have the same problem with
hammer spring
What hapen with you now
@@كريمعلي-ج1ث we made a upgrade kit ua-cam.com/video/sLEL22YIkKM/v-deo.html
@@AfricanAirOrdnance thanks lot
A question please, by turning the regulator, do you know how much you earn approximately, thanks
I forgot that the use of an added suppressor is appreciated.
He has thrown slug boat tail with it, no more.
a quarter turn = 25 to 30 bar
What stops the regulator from moving inside the plenum tube?
the front of the plenum tube is machined out to the OD size of the regulator so the regulator can only go so far into the plenum
What kind of ball does the Vulcan have behind the bleed screw?
@@ralstonraz not sure contact Airgun Technology and ask them
how much bar 170? also did you change hammer spring?
Wouldn’t those three adjustments put the reg over the 170 recommend max ?
@@Light_357 yes around 220 bar but it's the only way to push 40gn slugs at those speeds it does no harm to the rifle
Hi i have a question regarding your plenum. Has your plenum got a small air hole on both ends? Or just the one end. 👍🏽
both ends
Very impressed.. Is the barrel no choked?
No it is not .i got the details from the factory. 500mm version is chocked but 700mm is unchocked
also seem you didnot do anything with hammer spring just reg pressure incrased?!
Hello, is this a full time job for you? Do you supply PCP rifles? BTW, I really like your 45 gn slugs.
Thanks for watching yes this is my full time gig
I have one v3 in 25 caliber what I don't like is the sound when I shoot. What to do to change that unpleasant so
We brought out a whole upgrade kit that includes a Depinger to dampen that sound ua-cam.com/video/sLEL22YIkKM/v-deo.html
Wow nice vodeo mate 😊
@@PCP_HUNTER_UK thanks for watching
I just bought the same model at 0.25 Cal, the test report shows avg. fps at 1013 for 41 gr ZAN slugs. Is this too high?
Not at all
Hello again, regarding the regulator. What is the reg pressure set at in this video? Is it a spring type or washer type? Does the manufacturer of the rifle make the reg or is it bought 3rd party and if so, what is the brand of the reg ? At this stage, have you already changed the hammer spring to achieve these velocities?
220 bar The Reg comes installed on the rifle from AGT Hammer spring was changed the Reg does not have Bell washers or springs in it
@@AfricanAirOrdnance Interesting! The Reg has no spring or washers? How about doing a special video on the Reg design? That way we can see how it actually works. Many thanks
I contacted AGT about the max recommended reg pressure and they said it shouldn’t be set above 170 bar. Have you modified the reg so that it can withstand 220 bar? Or did you mean that 220 bar was the bottle pressure?
He will only show you regulator modifications and simple stuff. The hammers srping mods or any other mods in order to been able to work on 220 bars he will not tell you. Not very helpfull other than showing your gun shooting with a lot of power but that is all
What is the aluminium tube inside the plenum for
@@Premierslugs it's a spacer
@@AfricanAirOrdnance does the reg sit against it upto the valve , I Thought I saw in one of your videos the HP doesn’t have it
They say that this vulkan is just so much better than the fx impact 3 despite all the hype and marketing bullshit of the latter. Thanks for making up my mind.!!
Solid gun very reliable
Would you have any clue as to how much 1/2 turn on the regulator equals in psi or bar?
a quarter turn is roughly 35bar
I've just watched your video again and you are getting great power with very good accuracy but at 220 BAR I'm amazed you are not suffering valve lock. Are you 100% sure the plenum pressure is working at 220 BAR? BTW, are there any proper schematics of this gun?
Made a stronger hammer spring the reg works great even at 250 bar
You set your regulator at 220 😲
I'm scared to go above 170 do you think I'll be fine going 200 bar !!
What will the biggest (Weight in Grains) Slug be for a .22 Vulcan before you have to modify the magazine?.....I am looking to order one!
Around 36 to 38 gn
Sorry, I meant that by turning the regulator around you change from small plenum to large plenum.
Still, thanks for the information, thanks
@@Piupiu68az if you flip the plenum around then it will change
did you play with valve adjuster? or no it is just from factory setting
Only adjusted the regulator hand hammer spring
@@AfricanAirOrdnance ok, i see valve adjuster is important for accurecy testing.
What’s the shot count with the 40 g
around 45
Good video . But you didnt say how many shot you can get with this speed . Its so important . Tell us if you know .
If you put a 700 cc bottle on looking at around 40 shots at that speed
Thanks for watching
Hi from France , good video , is gun noisier after mod ? Thanks 👍
No not really very quite gun to start with
The Vulcan 3 has a very good Internal Suppressor
@@AfricanAirOrdnance ok , it’s the same thing for all the rifle ? Thank
Hi nico are you not restricted on power for air guns in France was looking to take mine to Brittany?
Ficou com quantos bar na reguladora?
180 thanks for watching
How many cc has the plenum on that rifle ?
120cc
كم مسافة التجميع ؟؟
what dia is that tube u have to push out the reg?
We are bringing out a regulator removal tool so you don't need to push the regulator out so it's less hassle to pull the regulator out
@@AfricanAirOrdnance when is this?
I know you mentioned that you were not trying to shoot groups, rather trying to check velocity. But how does the gun group at those speeds. The groups you shot were average for that gun. Thabks
Actually the groups in the first part of the video were much bigger at lower speed and got tighter with the increase obviously finding ammo that the gun likes is also very important again as I did state I wasn't shooting for Super tight groups but to get a 40 gn slug over 1000fps and the numbers were extremely consistent for that power output The bigger slugs 40 gn and 45 ,gn are designed for higher speed Old school Airgunners rule of thumb used to be for Airguns keeping your slug under 1000 fps was best for accuracy in pellets that is true but slugs things are changing fast
@@AfricanAirOrdnance thx for that bud! Would u make a video shooting those slugs and try to get them to group sub MOA. I have a few AGT Vulcans/Uragans from .177 to .762 and was just about to press the button on the Vulcan 3. Love the polygonal barrel on it but can’t seem to find any evidence on whether it can really shoot slugs sub MOA with minimal tinkering. Thx again
Thanks for the video.. very well done... the next step I'd love to see done... is the step to get very tight groups... seems to be every gets the tutorial to this point and won't go any further.. so is the next step to up speed a little more at a time to see what happens with accuracy?? And what would you recommend a safe speed for the rifle...any info we may need on hammer spring adjustments??? Does it need adjusting? Or should we just stay with reg pressures...it's just feels like we as newbys to the slug club are only getting half the story all of the time.... OK yes you need a slug the gun likes... but show us how it all goes for first shot and all the tuning to get to crazy groups at 100m
σε ποσο αποσταση ειναι ο στοχος
Hello friend, how much is the setting of that regulating valve??? What consistent range of shots do you have with 40 gr? Thank you
200 bar
Wow you done all that without adjusting the hammer.
defiantly adjusted the hammer strike
10:00
oh yessssss
bro next time use any tourch light are room light your video is very low light
Poxy adverts just ruin this , stopped watching halfway through first add !
Get rid of that infuriating background din.
will do
Very eratic
❤
Thanks for watching