Very easy to follow, you explained in great understandable detail. Replaced both my belts on my 94 G20. Belts installed safely and are spinning quietly. Thank you for all our Vids. Tony SD CAL
Replaced the pulley on my p10 because it came apart as well and never occurred to me to replace seal lol. After leaking all the oil I'm back doing the job again lol. Nice video and helpful tips.
I've done a couple of these and the dampeners on 95/96 sentra GA16DE motors. Wobble got so bad it started to eat into timing cover oil passages but caught just in time that it didn't get clear thru!
Thanks Eric I learned something for my 99 g20 I also wanted to ask you that there is a lot of rattle when I'm at a stop light but if I put it in neutral it smooth. I don't know if it's the belt tensioner or anything else!
Hey I have An 02 p11 my tensioner bolt that goes onto the side of the bracket came off -the 12mm one and not sure how to properly put it on. I couldn’t see from your video where the side bolt is connected to. So if u could tell me if it goes into one of the holes or in the long space In the brackets
Great video. Quick question. When you put the xxr rims on the rear did you have any problems regarding rhe rear wheel bearing hub dust cap not letting tge XXR center cap to stay in place?
no its not needed the crankshaft pulley is keyed meaning it will always fit at top dead center once you put it at top dead center so no needed to worry
@sethtreacy7576 I came across this issue on my car in the past. There is one more 14 mm bolt that goes on the bottom of the power steering pump you can try to loosen that up and see if you can move the pump backwards Normally you don't have to do this but in your case it might be the only way to do it
@@ERICSDIYGARAGE Infiniti delaers still sell them, but they're special order and they're almost $350. I called all the local salvage yards and they don't have them. I would rather get a used one, but if I'm forced to I'll buy a new one
Thank You Guys For Tuning In! YOU DO NOT Want To Miss Next P11 Video 😱 Stay Tuned & Thank You For Watching!
dude you are my real life hero. thank you so much!
My '99 is still going strong at 272k miles, just need to fix this oil leak lol
Awesome 👌 thank you for watching ! Keep it gong for many more to come!
Very easy to follow, you explained in great understandable detail. Replaced both my belts on my 94 G20. Belts installed safely and are spinning quietly.
Thank you for all our Vids. Tony SD CAL
Thank you dude ive been asking for a while now for this one lol need to replace my crank seal
my bad bro 😔 hope the video helps you out 👍and and thank you for watching!
Replaced the pulley on my p10 because it came apart as well and never occurred to me to replace seal lol. After leaking all the oil I'm back doing the job again lol. Nice video and helpful tips.
haha trust me I know how you feel lol! I appreciate your support!
Thank you very much for the video. You've saved me a lot of time.
You are really helpful thank you bro.
Great video thanks for sharing buddy
Thank you!
hey, the holes are for ballancing to prevent vibration.
My boi thanks bro
thank you for watching 👍
I've done a couple of these and the dampeners on 95/96 sentra GA16DE motors. Wobble got so bad it started to eat into timing cover oil passages but caught just in time that it didn't get clear thru!
Thanks Eric I learned something for my 99 g20 I also wanted to ask you that there is a lot of rattle when I'm at a stop light but if I put it in neutral it smooth. I don't know if it's the belt tensioner or anything else!
could be motor mounts
Hey I have An 02 p11 my tensioner bolt that goes onto the side of the bracket came off -the 12mm one and not sure how to properly put it on. I couldn’t see from your video where the side bolt is connected to. So if u could tell me if it goes into one of the holes or in the long space In the brackets
Great video. Quick question.
When you put the xxr rims on the rear did you have any problems regarding rhe rear wheel bearing hub dust cap not letting tge XXR center cap to stay in place?
I took it off
No need to put the crank on TDC in these vehicles? Please let me know. I'm about to do this tomorrow. Thanks Erick Great content
no its not needed the crankshaft pulley is keyed meaning it will always fit at top dead center once you put it at top dead center so no needed to worry
@@ERICSDIYGARAGE thanks for the quick reply. Now to change the leaking seal tomorrow. Thumps up bro. Keep up the great educational work.
@@ocesmekanics3831 thank you I appreciate it, good luck 👍🏻
Do more scat pack videos
How did you loosen the tension on the back tensioner you just cut and didn’t show you actually getting it
Loosen the 12 mm that's facing towards the firewall and than Loosen the 12mm long bolt in the back of the tensioner
@@ERICSDIYGARAGEI did that still isn’t loosening so I need to take the bold fully out
@sethtreacy7576 no you don't need to take it all the way out if it's not loosening use of prybar to manually move it back
I tried a long screw driver but it’s just not budging I’ve tryed hammering and prying :(
@sethtreacy7576 I came across this issue on my car in the past. There is one more 14 mm bolt that goes on the bottom of the power steering pump you can try to loosen that up and see if you can move the pump backwards Normally you don't have to do this but in your case it might be the only way to do it
I can't find the part anywhere, where's a reliable place to find one of them? My G20 needs a new one.
I had a difficult time finding one as well I used one from a salvaged yard
@@ERICSDIYGARAGE Infiniti delaers still sell them, but they're special order and they're almost $350. I called all the local salvage yards and they don't have them. I would rather get a used one, but if I'm forced to I'll buy a new one
you can also try a sentra 2.0 with a sr20 that's what I did
@@ERICSDIYGARAGE I'll look into that. Thank you! Also, dig the car. New here but looks snazzy.
Good shit
Same my car screams to high hell
people upgrade or downgrade however you look at to a lightweight crankshaft but idk how to feel about that because they have a mixed reviews
Ight