If you subscribe you could be in with a chance to win lots of prizes! In every new video we will be picking one lucky subscriber to win! We will be starting this very soon so make sure you watch our most up to date videos!
You should know that the 2 input ports have very different purposes. One is garden variety input to metering venturi, feeding the crankcase. The other is the air supply for stratified scavenging, which greatly reduces emissions and fuel waste from short-circuiting of some fresh air & fuel from transfers to exhaust. The idea being so supply air-only as first feed through transfers, so that can be exhausted. I've a few saws with that stuff, from 40 cc RedMax, 50 cc PPro, 61 cc Dolkita, 576 XP, XT, AT Husqy, so it's not exotic. Much preferred, in fact.
First thing to replace on new saws is the decomp,Learned this the hard way year old new saw blew up from having a decomp that failed and it was never used,so I remove them first thing. These new bicc Husky saw are nicer then anything else made.
Do you know if they are selling the connectivity device yet? Cannot find it on the spare parts section on Husqvarna website just has the device holder available.
I'm quite sure that the sprocket is the same as in the 572. So you can use the sprocket for the 572 and 3120 for a .404 chain. I've done this on my 572 and it stays sharp much longer than a 3/8.
I have 395s and 372s for all the falling I do. This is the first time I've seen an auto tune taken down. Very cool video. Thanks. I was curious about the cooling fins in the cylinder, do you think it's got more or less than the older husqvarna saws. ( 372 and 395 ) I dont really have any overheating issues. Just curious if the newer saws like this do well in that department. Thanks again. Really enjoy your guys work
I use my chainsaws in the city. 60-in diameter up to 48 inch 20 ft up to the first garage maybe 80 in. The first 10 or 15 ft off the stump is filled with spikes and nails. I was thinking 32-in bar with a carbide chain. What do you think. Rough cutting in the city. Hello from Piqua Ohio.
Nice review. But please, tell us about the cheap SKF bearings husky uses in the new 572xp, the ones that spit steel balls inside the crankcase. Do they use those in the new 592 as well?
SKF bearings are not cheap, but it is very concerning to hear that they are failing! I sure hope that the 592XP will not befall the same fate. I just bought one at just under 1,500 USD.
have a 555 autotune 1 of the first ones built has 31 hours on it according to my dealer. it sits in the shed cause it wont stay running and my dealer wont give me any thing for it!!! went back to my old saws had them rebuilt. $600 spent on a 555 that i cant use after 31 hours. just will not stay running. my dealer has changed every thing except the carb
The dual intake "ports" do not allow "twice as much air in". They are, as with all the new saws strato. The top channel feeds fresh air only to scavenge the transfers, the lower feeds fuel/air mix. This is purely because of dumb EPA /EU regs. High revving, bordering on lean running, less low end torque is the result. In big timber and 404 it's predecessor 395 will eat it. Same as with 660 v 661
So Josh you're telling us James spent the weekend in bed with the chainsaw and in the woods🤣🤣 no but serious it can be plugged into a laptop and the data can be downloaded from it that is clever that's a good bit of kit (Had to watch and listen again it uses a NGK plug and not a torch plug tut tut and jame bedded it in not been in bed with it over the weekend)but once again really good video
I’m a little disappointed with this saw have being using Past 4 weeks I’ve gone through 6 tanks of fuel starting to loosen up a bit very powerful and smooth saw. What I’m disappointed about air filter is not as good as the 572 & 395 xp small particles are still getting through under base of air filter not happy also the felling dogs are very flimsy you would think Husqvarna would put some decent dogs on a 90cc saw. They also claim it has more power than the STIHL ms 661 they feel pretty much even to me in power and in cutting speed not a big deal of difference for what it’s worth the STIHL ms 661 is $300 cheaper. No I wouldn’t buy this saw again.
Someone else commented that they were using a bit of waterproof grease where the filter meets the air intake. They said it fixed it completely. I imagine a silicone putty or something would do the same thing.
Hi Daniel very good point you made that will work. The comment I made about 592 xp Husqvarna has failed with there air filter set up I have to clean air filter after heavy days work running the saw hard. Saw dust particles are getting pass the filter into the manifold. As for the 395 xp I can run that saw hard for a week and it’s still clean no saw dust in manifold. The best filter set up I seen 395xp
@@tonytribisonna9886 I have a 592xpg back ordered. Are you pleased with it other than the air filter issue? It's a shame that the the saw is lacking in such a critical area but i'm going to use grease right away on mine.
Hi Daniel you will not be disappointed with this saw has plenty of power smoother lighter than 395xp and cuts quicker more chain speed and also louder make sure you wear good hearing protection . I’ve never had any starting issues I use good quality premium fuel 95 octane & good 2 stroke oil. Don’t run ethanol fuel Another thing I forgot to mention you won’t like the saw the way it runs the first few tanks of fuel auto tune constantly adjusting which is normal it should loosen up 4 to 5 tanks off fuel you will notice revs go up and so does power. I’m happy with the power gets better the more I use. I just hope Husqvarna make an improvement filter so it sealed up better but for now grease will have to do.
If you subscribe you could be in with a chance to win lots of prizes! In every new video we will be picking one lucky subscriber to win! We will be starting this very soon so make sure you watch our most up to date videos!
Are they the same size as the 572?Thank you I just found your channel I love it
@@hbhb8173 thank you 👍🏼 they are slightly larger than the 572xp
@@MachineryNation ty for your time
@@hbhb8173 thank you for your support of our channel 👍🏼
You should know that the 2 input ports have very different purposes. One is garden variety input to metering venturi, feeding the crankcase. The other is the air supply for stratified scavenging, which greatly reduces emissions and fuel waste from short-circuiting of some fresh air & fuel from transfers to exhaust. The idea being so supply air-only as first feed through transfers, so that can be exhausted. I've a few saws with that stuff, from 40 cc RedMax, 50 cc PPro, 61 cc Dolkita, 576 XP, XT, AT Husqy, so it's not exotic. Much preferred, in fact.
I just picked up a 592 last week. It starts so easy. Such a pleasure to run compared to my 500i. That third gen Autotune really makes it simple.
That’s awesome, nice one Jamison 😎
Which do you prefer. I would like to buy a new saw. But canny make up my mind. The 500i or the 592.
Cool video man! Really enjoyed the commentary! Well done!
First thing to replace on new saws is the decomp,Learned this the hard way year old new saw blew up from having a decomp that failed and it was never used,so I remove them first thing. These new bicc Husky saw are nicer then anything else made.
I am interested in one of these saws. Thanks for breaking this one down.
No worries, thank you John. If you are in the UK check out www.hayesmachinery.co.uk
@@MachineryNation I am not in the UK but it looks like you have a lot of good products to offer here.
@@johnrosier1686 thank you John. We really appreciate it 🤩
Excellent presentation and introduction to the new saw. Thank you.
Thank you DC
Do you know if they are selling the connectivity device yet? Cannot find it on the spare parts section on Husqvarna website just has the device holder available.
A guy with a bad shoulder owns a 395. Always makes for a sore arm when starting cold. My question is will the 592 start easier?
You will have to buy one to find out haha. We have other videos on our channel where you can see us starting them 👍🏼
Starts like a 70cc saw. Second pull. Use de-comp and primer on morning starts for best results.
Great break down video. Love mine. Great saw!
Thank you.
I'm quite sure that the sprocket is the same as in the 572. So you can use the sprocket for the 572 and 3120 for a .404 chain. I've done this on my 572 and it stays sharp much longer than a 3/8.
Yes the same rim sprocket will fit them all 👍🏼
Is there a time to break the saw in? Have them new and it looks like it's not at full power.
I wish I owned one in Vietnam
I have 395s and 372s for all the falling I do. This is the first time I've seen an auto tune taken down. Very cool video. Thanks. I was curious about the cooling fins in the cylinder, do you think it's got more or less than the older husqvarna saws. ( 372 and 395 ) I dont really have any overheating issues. Just curious if the newer saws like this do well in that department. Thanks again. Really enjoy your guys work
I use my chainsaws in the city. 60-in diameter up to 48 inch 20 ft up to the first garage maybe 80 in. The first 10 or 15 ft off the stump is filled with spikes and nails. I was thinking 32-in bar with a carbide chain. What do you think. Rough cutting in the city. Hello from Piqua Ohio.
Nice! Nails are never a friend of a chain hey.
Nice review. But please, tell us about the cheap SKF bearings husky uses in the new 572xp, the ones that spit steel balls inside the crankcase. Do they use those in the new 592 as well?
I can’t confirm but it is a different part number than the 572 if this helps 👍🏼
SKF bearings are not cheap, but it is very concerning to hear that they are failing! I sure hope that the 592XP will not befall the same fate. I just bought one at just under 1,500 USD.
Very good chainsaws
Good videos Josh
Where can I buy the diagnostic software and cable?
You can’t it’s dealer only
have a 555 autotune 1 of the first ones built has 31 hours on it according to my dealer. it sits in the shed cause it wont stay running and my dealer wont give me any thing for it!!! went back to my old saws had them rebuilt. $600 spent on a 555 that i cant use after 31 hours. just will not stay running. my dealer has changed every thing except the carb
It might well be the carb then if he has changed everything else 👍🏼
make more videos like this 👍 useful
How can i order from Philippines..
Same clutch as 572xp
Nice video! Just subbed... trying to convince myself I need a 592! Have you done a similar video on the 585?
Thank you 🤩 we have not seen a 585 yet. So desperate to get one 😭
I like it this kind of chainsaw..,how can i buy it
You will need to find where your local dealer is 👍🏼
5.87Nm torque, is very great!
SUPER !!! 👍👍👍 🤝🤝🤝
Thank you! 😀
The dual intake "ports" do not allow "twice as much air in". They are, as with all the new saws strato. The top channel feeds fresh air only to scavenge the transfers, the lower feeds fuel/air mix. This is purely because of dumb EPA /EU regs. High revving, bordering on lean running, less low end torque is the result.
In big timber and 404 it's predecessor 395 will eat it.
Same as with 660 v 661
The 661 is not a strato saw
@@johnwalt3504 I stand corrected, thanks
Sounds like this guy doesn't know as much as he thinks he knows about this saw. But I'm a stihl man anyway just watching for entertainment
Great
So does it have a carburetor or does it have a fuel injected module.
It has the latest Autotune carburettor 👍🏼
Why didn't you take off the fly wheel?
Entre la Husqvarna 592xp y la Stihl 662 cuál consideras que es mejor,tomando en cuenta la calidad de materiales y durabilidad con el tiempo.
Stihl 662, what is?
Absolute same chainsaw like my 2016 year 545mk2 only difrance is 41cc
u said demo saw so what did hus give u a free saw ??? phew id show alotta love lol cost me almost 1400 to buy mine
hey nice video, but what about Husqvarna 585？
As soon as we can we will put some videos up, I promise 👍🏼
@@MachineryNation super I will stay tuned 😃
So Josh you're telling us James spent the weekend in bed with the chainsaw and in the woods🤣🤣 no but serious it can be plugged into a laptop and the data can be downloaded from it that is clever that's a good bit of kit (Had to watch and listen again it uses a NGK plug and not a torch plug tut tut and jame bedded it in not been in bed with it over the weekend)but once again really good video
Hahahahaha cheers Nev! I love bedding saws 😂😂 NGK all the way haha
Love it
Untuk saya (1)satu master Cain Saw sebagai promosi di Indonesia master
Thank you 🤩
Goog
Got a 572 +592.choice/husky are just better quality/everything else is junk.next.
The flywheel is a disaster taking off
Modification ability? There never as good as they CAN be. And a primer bulb,...really... Ive never had trouble starting a good running PRO husky.
Yeah, everything is mod-able, just depends how brave you are 👍🏼
Super dravec 😅😆🤗🚜🐻🍗♥️😛😝😀🐙🎻🌽💪💪💪💪
Give me manual carb any day of the week if this thing thinks it's running well and it's not your fucked
Husqvarna are also bringing out the 585 which is pretty much the same as this, but with a manually adjustable carb 👍🏼
@@MachineryNation and how many kilos ?dry weight?no bar
been a long time since auto tune has had issues.
@@Rob-tl9md Using my 545mk2 from 2016 Auto tune wit zero problems and saw has ower 2800 working hrs.
I’m a little disappointed with this saw have being
using Past 4 weeks I’ve gone through 6 tanks of fuel starting to loosen up a bit very powerful and smooth saw.
What I’m disappointed about air filter is not as good as the 572 & 395 xp small particles are still getting through under base of air filter not happy also the
felling dogs are very flimsy you would think Husqvarna would put some decent dogs on a 90cc
saw.
They also claim it has more power than the STIHL ms 661 they feel pretty much even to me in power and in cutting speed not a big deal of difference for what it’s worth the STIHL ms 661 is $300 cheaper.
No I wouldn’t buy this saw again.
Someone else commented that they were using a bit of waterproof grease where the filter meets the air intake. They said it fixed it completely. I imagine a silicone putty or something would do the same thing.
Hi Daniel very good point you made that will work.
The comment I made about 592 xp Husqvarna has failed with there air filter set up I have to clean air filter after heavy days work running the saw hard.
Saw dust particles are getting pass the filter into the manifold.
As for the 395 xp I can run that saw hard for a week and it’s still clean no saw dust in manifold.
The best filter set up I seen 395xp
@@tonytribisonna9886 I have a 592xpg back ordered. Are you pleased with it other than the air filter issue? It's a shame that the the saw is lacking in such a critical area but i'm going to use grease right away on mine.
Hi Daniel you will not be disappointed with this saw has plenty of power smoother lighter than 395xp and cuts quicker more chain speed and also louder make sure you wear good hearing protection .
I’ve never had any starting issues
I use good quality premium fuel
95 octane & good 2 stroke oil.
Don’t run ethanol fuel
Another thing I forgot to mention you won’t like the saw the way it runs the first few tanks of fuel auto tune constantly adjusting which is normal it should loosen up 4 to 5 tanks off fuel you will notice revs go up and so does power.
I’m happy with the power gets better the more I use.
I just hope Husqvarna make an improvement filter so it sealed up better but for now grease will have to do.
In US, 661 is over $300 more than 592.
$1589 vs $1260
Once I see chisel and a hammer, I turn this off, dislike as well.
I bet you’re fun at parties 😂