I've been ba certified mechanic over 40 years and that is not the correct way to pack wheel bearings. Also why not replace the worn and overheated brake shoes? If you had that much trouble trying to get the brake drum on, why not back off on the brake shoe adjustment the re adjust them. I didn't see him bleeding the brakes also since he disconnected the brake line. Shoddy job.
And people paid him for this garbage... lol. First the grease job on the bearing was pathetic, but the icing was watching him take and put the excess grease back in the can with dirty fingers. Nothing like putting fresh dirt in with "new" grease... Just wow.
While there is much to criticize in this man's methods..there is also room to say that just having a job done by a "professional" is no guarantee either. Had a new cylinder head put in replacing one with nearly 200,000 miles on it. "Professional" didn't think it would be necessary to have new rocker arms riding on a new cam. I was out $400 having his mistake corrected.
You take the emergency brake cable out by putting a hose clamp around it to compress all the tabs at once and then put a screwdriver or punch against the end of that housing and tap on the punch to drive it out of the backing plate. Simple.
Is it me or are those break shoes about done for and why doesn't he at least adjust the shoes so the hub will go on and then readjust the break on that side and I hop he bleeds those breaks after cracking the break line wide open.
Absolutely incredible, hammer and home made chisel, personally I'd have tried a puller, wonder how long those bearings will last without being hand packed, so much done wrong, I've seen so much on here watched one guy heat the drum in his oven and placed the bearing in the freezer, put them together with loads of smoke and flames, obviously with a lose of the grease, how many unsafe cars are on our roads with so many UA-cam home mechanics trying these tricks, very frightening
Has to be some where in africa or maybe india They would not do here No way. Very rough back yard job. Not knocking them. Far from it. Did not see them bleed brakes or adjust brake cable. I would change brake shoes.seemed glazed and wornout he put new drum on did not put new shoes , Also looked like leaky wheel cylinder.
He should have obserbed the procedure to secure a correct preload on the bearing which means using a torque wrench whilst spinning the wheel then backing of the nut guidence should be gained from car dealer or haynes workshop manual consearning preload procedure.
With the brake drum design wheel brake replacement is very fast. Try and do it that fast on disc brake when the bearing are inside the steering arm or inside the rear axle.
Disagree. Removing and reinstalling a disc brake wheel is much easier. No bleeding or brake adjustments required. I have t worked on a drum brake in a while but couple years ago replaced wheel hubs on a disc brake system and found it quite simple.
I have to disagree! I would rather do disc brakes, i can do them in a fraction of the time it takes to do drum brakes. With drum brakes you have to see if the cylinder is rusty, then try to adjust it & try to get the drum off. Sometimes have to heat the drum to break it free. Disc brakes, just a couple of sockets, a C clamp, & you'll be done in 10 minutes. No need to bleed brakes, don't have to replace rusted cylinders. If a caliper is leaking, it will take a little longer, but still easier than drums. Even replacing bearings isn't bad with disc brakes. Some vehicles today have sealed bearings, just unbolt the old hub & bolt the new hub in.
Le mec fait sa chochotte avec son petit bâton pour graisser le roulement et ne pas se salir les mains puis finalement à la fin, il y passe allègrement le doigt pour bien nettoyer autour, cherchez l'erreur.
Горе слесарь. Первый и последний инструмент молоток. Им можно херачить по всему. По цапфе, по резьбе шпилек, по обойма подшипника, по сальнику и т.д. пока такие слесаря есть, мы без работы не останемся.👍🤣
The title of the video suggest that a man replaced wheel bearings belonging to himself. This is a video of a man replacing a completely destroyed wheel bearing and axle that did not belong to him. There's no way a man with those mechanical capabilities would have driven a wheel in that condition
Ola meu amigo não se coloca a capa do rolamento batendo com o próprio têm que ter uma peça de apoio e uma prensa ou ate com a marreta o rolamento vai danificar a capa nova !
Nobody will follow it here obviously we don't even have such primitive bearings. Still wouldn't hammer on it. These metals ain't fully hard, will deform. It will bend the shaft also.
Sorry, good work getting everything apart but the wheel bearings were not packed correctly with grease. These bearings will not last nearly as long as originals. Grease must be packed/forced inside the cage completely, smearing grease on races & rollers is not adequate
How bizarre! They clearly have most of the right tools but don’t seem keen to use them. So much wrong here, I think he is making it up as he goes. I feel I should buy him a much bigger hammer, he likes them
سایک غلطی کی ھے جس کا خاص خیال رکھنا چاھیئے۔جتنے بھی بولٹ لگائے ھیں سب خشک تھے ان پر تیل لگاتے یا گریس۔آئیندہ کھولنے میں ضائع نھیں ھوتے۔امید ھے آئیندہ خیال کریں گے۔
I am not sure about record time, but for the tools he had, it was not bad. I credit him for what he did, but the way he'd lubed bearings is wrong. Bearings need to be packed, not submerged in grease. A little heat on the inner bearing race would have made it easier. Driving races was not entirely correct, either. If they are not fully seated, your bearing preload will loosen up.
This dude shouldn't have showed several incorrect and improper ways of doing the job at hand. He got the job done but not to my standards. Unfortunately jobs like this gives any auto tech a bad reputation.
Another 10mins of my life im not going to get back watching why do i do it to myself, gess we the suckers for watching, all about clicks surly no one takes it seriously😮
Anyone else think that the handbrake lever in the hub was a bit seazed, and all those new parts fitted but no new brake shoes on a new brake drum. The driver will need to bed those old shoes in on a new drum.
Back yard hackers, disgraceful work.
Well, they drove it to that point so this kind of hackery is to be expected
I would not this guy touch my cloths line let along do repairs on my car clearly not qualified
I've been ba certified mechanic over 40 years and that is not the correct way to pack wheel bearings. Also why not replace the worn and overheated brake shoes? If you had that much trouble trying to get the brake drum on, why not back off on the brake shoe adjustment the re adjust them. I didn't see him bleeding the brakes also since he disconnected the brake line. Shoddy job.
exactly what i was thinking.
Wrong in every way imaginable. It must be Jesus because it's a miracle.
But the Vaseline used for bearing grease is going to outlast it all😂😂😂😂😂😂😂😂😂
Would have used a socket to remove the large but myself
Exactly Edward, I am a certified mechanic myself and agree with your response.
Don't follow this tipe of job, could be very dangerours!!!
This is the reason why I do my own work on my car.
Someone needs to teach this guy how to pack a bearing in his hand.
I was going to say the same thing. He probably can't afford a bearing packer, but he could at least learn to pack wheel bearings by hand.
I'm a welder and I know it's the palm of the hand
Shocking, indeed...
Very unprofessional work.
Good thing he's not a professional
😅😢
Very Good Like Old School Mechanics 👏👏
If that's how you pack your wheel bearings, no wonder you burnt them up. I wouldn't let you work on my wheel barrow.
None of that was done correctly
Thank you my friend 🌹🙏
"RECORD TIME"! "WHAT"?! 😆
They meant the longest time
Даже досмотреть не смог . Кровь из глаз .
😂😂😂Есть рукожопы но есть и жопоруки , я досмотрел и мне медальку .😂
And people paid him for this garbage... lol.
First the grease job on the bearing was pathetic, but the icing was watching him take and put the excess grease back in the can with dirty fingers. Nothing like putting fresh dirt in with "new" grease... Just wow.
Lazy mechanic, that is not the proper way to grease the bearing.
Wow, a genuine Handy Andy realistic pliers and screwdriver set and a sharpened piece of rebar. That's making do....
Just needs to learn how to pack bearings, because he sure didn't pack those bearings correctly.
Yes it is when money is tight you compromise!
Съемник подшипника? Не, не слышал
Just about the worst I've ever seen
Thank you my friend 🙏♥️
Оказывается нетолько у нас зубило и ручку на молоток делают из куска арматуры.
Bestia¡¡¡¡ animal¡¡¡¡ existen extractores de rodamientos... y encima sube un video como que lo hiciera bien....
😂 it’s hammer time.
Barbaric
How long will those bearings last? Lord have merci on the Monkey!!!
Not sure yet
Get lost they will last as long as need be !
Зато представьте сколько он таких же уников собрал. Европа одним словом.
While there is much to criticize in this man's methods..there is also room to say that just having a job done by a "professional" is no guarantee either.
Had a new cylinder head put in replacing one with nearly 200,000 miles on it. "Professional" didn't think it would be necessary to have new rocker arms riding on a new cam. I was out $400 having his mistake corrected.
Tragedia 🤦♂️ Gorszej pod każdym względem wymiany łożyska nigdy nie widziałem 🙆♂️
You definitely need a brass hammer
He is a real cowboy mechanic 😂
He’ll be replacing that in about 6 months.
Tudo na base da marretada, nem passo perto desse mecânico, se pode chamar esse camarada de mecânico
You take the emergency brake cable out by putting a hose clamp around it to compress all the tabs at once and then put a screwdriver or punch against the end of that housing and tap on the punch to drive it out of the backing plate. Simple.
I use those pliers for removing vacuum hoses.
He did good with very limited basic tools...but he definitely didn't finish in record time...😊😊😊
Yes, thanks
Is it me or are those break shoes about done for and why doesn't he at least adjust the shoes so the hub will go on and then readjust the break on that side and I hop he bleeds those breaks after cracking the break line wide open.
Absolutely incredible, hammer and home made chisel, personally I'd have tried a puller, wonder how long those bearings will last without being hand packed, so much done wrong, I've seen so much on here watched one guy heat the drum in his oven and placed the bearing in the freezer, put them together with loads of smoke and flames, obviously with a lose of the grease, how many unsafe cars are on our roads with so many UA-cam home mechanics trying these tricks, very frightening
Thank you very much!
Made a right mess of that shaft.
Been a mechanic for 135 years,,, this will be just fine 😂😂
Я думаю он частенько на этом авто так меняет,потому что рожковым ступичную гайку привычно легко открутил🤣
🙏🏻🙏🏻
He doesn't have any Idea what he doing 😅 every thing is balaaa balaaa balaaa 😂
I don't think that was fast at all. Especially given that it was heavily edited and played at fast speed.
Has to be some where in africa or maybe india
They would not do here
No way. Very rough back yard job. Not knocking them. Far from it.
Did not see them bleed brakes or adjust brake cable.
I would change brake shoes.seemed glazed and wornout he put new drum on did not put new shoes ,
Also looked like leaky wheel cylinder.
I like your rerod chisel
Hey amigo !!! Y las zapatas de freno vieja con la masa nueva?🤔. faltaría ese reemplazo, con los frenos no se escatima!!!❤
He should have obserbed the procedure to secure a correct preload on the bearing which means using a torque wrench whilst spinning the wheel then backing of the nut guidence should be gained from car dealer or haynes workshop manual consearning preload procedure.
Great point!
He’s probably never heard of a torque wrench
ทุกระบบจบที่บัง
😂😅😂😅😂
Видео о том как не нужно делать
Great video thank's !
Thank you too!
With the brake drum design wheel brake replacement is very fast. Try and do it that fast on disc brake when the bearing are inside the steering arm or inside the rear axle.
Disagree. Removing and reinstalling a disc brake wheel is much easier. No bleeding or brake adjustments required. I have t worked on a drum brake in a while but couple years ago replaced wheel hubs on a disc brake system and found it quite simple.
I have to disagree! I would rather do disc brakes, i can do them in a fraction of the time it takes to do drum brakes.
With drum brakes you have to see if the cylinder is rusty, then try to adjust it & try to get the drum off. Sometimes have to heat the drum to break it free.
Disc brakes, just a couple of sockets, a C clamp, & you'll be done in 10 minutes. No need to bleed brakes, don't have to replace rusted cylinders. If a caliper is leaking, it will take a little longer, but still easier than drums.
Even replacing bearings isn't bad with disc brakes. Some vehicles today have sealed bearings, just unbolt the old hub & bolt the new hub in.
A real pro
How not to replace a wheel bearing video.
What country are you in?
Un meccanico macellaio😅😅😅
Che lavoriiiii😄
In what universe does the axle nut come off so easily.
Acho que ele não sabe o que é um sacador de rolamento 😅
Había olvidado colocar los tornillos al armarlo.
We would use a torch to flat top the bearing race and not hurt the shaft. Sand the shaft and install new bearings.
Подшипник видимо из алюминия если зубилом свободно рубит
Ну разве можно так подшипники устанавливать, бить по внутренней обойме?
Из чего он сделан😅подшипник зубилой разрубил
Ce métier je c'est ma vie
Le mec fait sa chochotte avec son petit bâton pour graisser le roulement et ne pas se salir les mains puis finalement à la fin, il y passe allègrement le doigt pour bien nettoyer autour, cherchez l'erreur.
Горе слесарь. Первый и последний инструмент молоток. Им можно херачить по всему. По цапфе, по резьбе шпилек, по обойма подшипника, по сальнику и т.д. пока такие слесаря есть, мы без работы не останемся.👍🤣
🤔🤔 A comedian at work !!😆🤣😂
The title of the video suggest that a man replaced wheel bearings belonging to himself. This is a video of a man replacing a completely destroyed wheel bearing and axle that did not belong to him. There's no way a man with those mechanical capabilities would have driven a wheel in that condition
Ola meu amigo não se coloca a capa do rolamento batendo com o próprio têm que ter uma peça de apoio e uma prensa ou ate com a marreta o rolamento vai danificar a capa nova !
Гайковёрт в наличии. Он рожковым ключём откручивает! Талант.на шпильках резьбу захреначил, потом их ставит. Есть пресс, обойму молотком забивает.
Nobody will follow it here obviously we don't even have such primitive bearings. Still wouldn't hammer on it. These metals ain't fully hard, will deform. It will bend the shaft also.
Арматурой перерубить подшипник.... Однако!!
Serviço grosseiro, medieval ainda bem que usou uma Esmerilhadeira e não um maçaricos
En el mundo de la herramienta existe una que se llama EXTRACTOR úsalo que te ahorrará tiempo y dinero
А подшипник - пластилиновый ????
Наглядное пособие, как не надо делать !!
Necessity may be the mother of invention, but it might just be the death of this clown
Record time? What was that like several days and a delivery of a whole new part?
Sorry, good work getting everything apart but the wheel bearings were not packed correctly with grease. These bearings will not last nearly as long as originals. Grease must be packed/forced inside the cage completely, smearing grease on races & rollers is not adequate
Back in the day packing was done in your hand by forcing the grease into the bearing the only way I know & my dad showed me that one👍
Thanks for sharing
90 day warranty? Lol
Cara, ta tudo errado, até oq ele faz "certo" ta errado. Até no final do video da pra ver que o eixo ta com folga quando ele chuta a roda
Это его автомобиль, он каждую неделю ремонтирует.
Kia car My friend 🌹🙏
Los picapiedras reparando el trocomobil😂😂😂😂😂
SHOW 👏👏👏 from Salto SP Brazil.
Those brake shoes could fo with changing?
Si uviera lavado las bamdas uviese sido mas elegante queda un trabajo sucio
muito bom trabalho parabéns nota 10
Thank you my friend 🌹
Is this Tipa?
No gloves, no safety glasses and just (mainly) hammer and chisel. Bucher.
Propio un lavoro da pakistano o algerino gia visto farlo martello cobran toglie tutto 😅😅😅😅
That’s not how you pack a bearing
Wrong way to pack grease into thee bearing.
That bearing won't last long. You do not use the cone to put the cup in the hub, all you do is damage the bearing
How bizarre! They clearly have most of the right tools but don’t seem keen to use them. So much wrong here, I think he is making it up as he goes. I feel I should buy him a much bigger hammer, he likes them
سایک غلطی کی ھے جس کا خاص خیال رکھنا چاھیئے۔جتنے بھی بولٹ لگائے ھیں سب خشک تھے ان پر تیل لگاتے یا گریس۔آئیندہ کھولنے میں ضائع نھیں ھوتے۔امید ھے آئیندہ خیال کریں گے۔
Al that work and did not replace the wheel cylinder and springs or clean up the entire hub. Come on man!
I am not sure about record time, but for the tools he had, it was not bad. I credit him for what he did, but the way he'd lubed bearings is wrong. Bearings need to be packed, not submerged in grease. A little heat on the inner bearing race would have made it easier. Driving races was not entirely correct, either. If they are not fully seated, your bearing preload will loosen up.
This dude shouldn't have showed several incorrect and improper ways of doing the job at hand. He got the job done but not to my standards. Unfortunately jobs like this gives any auto tech a bad reputation.
Another 10mins of my life im not going to get back watching why do i do it to myself, gess we the suckers for watching, all about clicks surly no one takes it seriously😮
♥️♥️♥️
Done does not equal done right.
🙏🏻🙏🏻
Your fired.
एक्सलची आय झवली. हा मेकॅनिक आहे का धवड. सगळच बडवून काढतोय.
Anyone else think that the handbrake lever in the hub was a bit seazed, and all those new parts fitted but no new brake shoes on a new brake drum. The driver will need to bed those old shoes in on a new drum.
You Didn't Clean Or Brush Off The Rusty Parts lol
Hi hi hi … yep thats the way you do it 😜
New brake shose
Brut force and stupid works sometimes 😂