Bmw e36 Acceleration M5xxB28 BW300sx 300deg.cams solid lifters
Вставка
- Опубліковано 17 кві 2018
- First test at 1.2bara , reduced ignition and reduced rev to 7300rpm
Fuel PB98
Engine building By Alek
Engine Spec :
Head M52 with m50nv valves and springs
Porting head
33mm solid lifters conversion
Grinding Cams IN 306deg EX304 lift 10,4mm / 10,2mm
12mm head bolts
Stock head gasket
Block M50b25 - 1mm
Cr 8,6
Pistons N54b30
Rods M50 NV
Crankshaft m52b28
Turbo Borg Warner s300sx 60mm
Ecumaster Emu managment unit performance by Alek
Two-disk clutch from - k64.pl
Siemens deka 630 injector
044 fuel pump
exhaust 3,5" dp to 3"
wg turbo works k64 and scream pipe 50mm
bov greddy
building topic on forum
www.turbobmw.com - Авто та транспорт
Says no traction and does a massive clutch kick 😃
I like that - whole built used only BMW parts , it's just a lot of search and work but it is worth it 👌
konkret! świr, czekam na postępy w projekcie ;)
lata kozak musze sie wziasc za swojego , motywujacy filmik , zapierdala jak wsciekly:D
Hello, what solid lifters did you use ?
Thank you.
Siema skrzynia biegów z czego tam była? Mam dyfer 3.07 skrzynie z e36 2,8 ale biegi są sporo krótsze od tego co widac u ciebie
Wicked! What’s the car doing now ? Does it still live or is this one gone with the wind lol ?
Been wondering how solid lifters would be!
Hi Alek,
I work on similar project currently just smaller cams, I am also using emu from ecumaster, of course zi cannot ask your for a map or tune of yours)) but can you please email me a log with a couple of spools so I can at least know where to start from when setting my basemap? thank you in advance
nice project dude, I got a simplier turbo 528 m52, can you tell where did you get this cam?
etniesks In poland some guys name "Rewar" from Kraków , they grindng cams for me
Witam, mam pytanie, co zrobiły niestandardowe wałki rozrządu w tym silniku, jak zmienił się charakter silnika, skoro wszyscy budują turbo na fabrycznych wałkach rozrządu?
i want put solid lifters in my m52
how did you do ?
U kogo szlifowałeś wałki? Planuję zbudować troszkę mocniejsze n/a M52TUB28 i szukam kogoś kto by ogarnął. ;)
I co zbudowales ten silnik ?
fk sake this is scary fast only watching the speedo cant imagine what its like inside
0:08 fuel needle ran away never to be found again
What chassis mods? Stock diff and rear suspension would surely explode with such huge power increase....
You'd be surprised lol
Do you have the spec of the turbo?
BW sx300, but is it 0.88 a/r with singel scroll or 0.91 a/r with twin scroll? Thank you?
Hi, it was a P/N 177272
@@AlekHKSD Thank you!
God that e36 sounds like it wants to kill someone😂
Did the n54 pistons fit with no modification?
No modifications needed
@@rawadalkhoumassi8983 modification is needed :)
Do ilu to się kręci? Wałki robią robotę 👍
na filmie do 7300rpm , teraz po ponownym strojeniu do 7500rpm
Vanos deleted on this? M52 head but cannot see the vanos?
There is just vanos head case, valve/guide/spring is form NV and custom cams without vanos
If you put n54 pistons in a b28 crank you will get 8.5 cr?
almost to get such a cr I also had to lower the plane of the block by 1 mm
@@AlekHKSD so then what did you put for the head gasket stock thickness ? Not possible if you took a 1mm off the cylinder head or the crankcase ?
Rly pull hard like new m3
With about 600hp this pulls much much harder than an M3.
Stock Valve Springs?
Yes
No traction because you hit cluch
why on 300+ degree cams rev limiter is on 7k?
ile koni ?
cos koło 600
Hello cams custom ? Thank
yes cams is custom ( grinding )
From cams m50b25nv ?
@@AlekHKSD Helo Wath problém doing this idle ????
Jak auto sie studzi w garazu to asfalt sie jeszcze zwija
Na filmiku jest głowica bez vanosa 🤔
Bo ma dekiel z blachy dorobiony 😎
600cc injectors are too small for 8k
yeah obviously ur not gonna have traction if you clutch kick lol