How To | 2007-2015 | Mazda CX9 | Brakes | No Specialty Tools
Вставка
- Опубліковано 19 бер 2021
- #MazdaBrakes #Diy #HowTo #EasyStepByStep
Vehicle In This Video: 2011 Mazda CX9
3.7L (Gas)
Oil Type: 5W-20
Oil Capacity: 5.5 Quarts
In this video we ll show you how to do brakes with common home\garage everyday tools.
easy step by step process
Im Using EpedmicSound for music click here: www.epidemicsound.com/referra...
Support Us On PAYPAL: bit.ly/3r4DPdJ
--------------------------------------TOOLS I OWN--------------------------------------
Wheel Stud Installer amzn.to/39VUDNx
Disposable Gloves amzn.to/2Isg9yq
Toyota/Lexus Oil Filter Tool amzn.to/2VtyQEP
Vacuum Brake Fluid Bleeder amzn.to/2Jffy3f
Gearwrench Ratcheting amzn.to/33e3VRp
7-Piece Spare Tire Retrieval Tool Kit amzn.to/3o0sE3D
Oil Filter Wrench Wrench Kit amzn.to/2UXwI7Y
Oil Filter Pliers amzn.to/3kZz5SB
Craftsman 1/2 Impact Sockets Set amzn.to/2V0Zyog
Screw Driver Set amzn.to/2V1PNpE
Hand Impact Driver Set amzn.to/39cZ9at
Dual Piston Brake Caliper Push Tool amzn.to/2KDvGfI
Wind Back Brake Caliper Tool Set amzn.to/3nUmuSj
--------------------------------------------------------------------------------------------------------
If this video helped, let us know in the comments, and if you liked this tutorial, leave a like and subscribe fore more content like this! Thanks for watching!
DISCLAIMER: This video description contains affiliate links, which means that if you click on one of the product links, I’ll receive a small commission. - Авто та транспорт
The tool you used to remove the large flat head screws "is" and special tool in most DIY garages.
Thanks for the video, Bud! It made the job a lot easier.
Awesome 👍
Fantastic video, thank you
Great video! So I did my front brakes and blew out my power booster. I'm guessing it was just old, seals, etc. She has 200k miles. The rear pads are hollering but I'm hesitant to change them because I might jack up the booster again. Our mechanic suspects it happened before when I compressed the caliper pistons. Thoughts?
What are the torque specs on the caliper bolts? And what direction was the top pad clip facing, in or out? Facing in looks like it would rub on the disc.
i wish you did the rear wheel also. how to adjust the parking shoe
One additional question, taking the original pads out there were very tight in the little stainless guides. Putting in the new PowerStop pads and guides the pads are also very tight. In other vehicles the pads always slid in with little to no force. I am guessing I need to file out either the guide area or the ears on the pads a little in order for them to slide feely. Must be something slightly out of tolerance on this Mazda.
clean stainless guides outside and then pop them out and clean rust/dirt/corrosion that builds up under it...that should take care of it, don't force pads on those guidelines if they don't want to go smooth , it might lock up the brakes
What is with dust shields missing on all CX9 videos?
idk lol rust maybe
What do you do when your pins don't line up and your caliper won't seat down properly?
Lube pins make sure they move freely and push pins in while with other putting caliper on
Does one need to replace the rotor too?
it depends on mil/shapeofrotor/vibration on braking/rust/based on high milage (yes) etc
What's that punch Philips head tool??
Impact screw driver
Do this also good for a 2014 cx9?
Yes
What’s that special tool called bro?
@@stevencordova3160 which one?
The one you used to remove the rotor screws
I see lots of special tools in this video. LOL