@@TheRaccoonFPV i connected ma naked gopro straight to the power leads and it worked for like a day, than it stopped working, now it only works with the original battery from gopro. Do you have any idea, what could cause that? I only get SD ERR reading, but my SD card is working.
@@TheRaccoonFPV unfortunatelly, i didnt have any crashes. do i need to install LABs firmware? It worked before with original firmware, and now im trying my luck with labs. What if i solder it straight to the BEC from GEPRC?
I had the same problem at first. The GepRC board was not correctly in place. Two of the lower connectors had clicked but the top one was still loose. Had to install the board again and got it finally connected after some struggle. Connectors were little bit off so I had to carefully bend the board a bit to get the connectors to line up while installing. Works well now 😊
this does not help me! I have spent all monrning trying to get this thing connected go my phone app. Originally it looked like it did but then I've been getting warnings it cannot connect as well as the battey is too low! this is getting very frustrating here!!!
@nitefieldfpv i believe i bought a balance lead adapter and plugged it in to get power. However keeping it powered and not cooling it is risky. But then i crashed it a while ago and havent been able to get it to work
Even when I have the Hero 9, and interested in features of the Hero 10 that just dropped, I still also want this geprc naked 8 for my cinewhoop🥲👌 life is hard🤣
Thanks for the video! This was really helpful for me. I can't wait to put this naked GoPro on my quad once it's built!
hey, Can I solder geprc gopro to my esc + - where is the XT60 ?
Yes red wire goes to plus black to minus
@@TheRaccoonFPV i connected ma naked gopro straight to the power leads and it worked for like a day, than it stopped working, now it only works with the original battery from gopro.
Do you have any idea, what could cause that?
I only get SD ERR reading, but my SD card is working.
@@FrederiQQ that’s your GoPros cpu chip did you have a collision? because that would explain it
@@TheRaccoonFPV unfortunatelly, i didnt have any crashes.
do i need to install LABs firmware? It worked before with original firmware, and now im trying my luck with labs.
What if i solder it straight to the BEC from GEPRC?
@@FrederiQQ to be honest im 99% sure its dead, you can try soldering to the board but that shouldnt be the issue unless the connector looks fucked
Is it safe to run off a 4.7v pad?
Perfect working
My ears are bleeding.
mine are too
Stuck in my doop doop doop doop head doop doop doop doop
Mine gets to the hero8 screen but freezes there, might need to send it back
I had the same problem at first. The GepRC board was not correctly in place. Two of the lower connectors had clicked but the top one was still loose. Had to install the board again and got it finally connected after some struggle. Connectors were little bit off so I had to carefully bend the board a bit to get the connectors to line up while installing. Works well now 😊
Thank you! :)
this does not help me! I have spent all monrning trying to get this thing connected go my phone app. Originally it looked like it did but then I've been getting warnings it cannot connect as well as the battey is too low! this is getting very frustrating here!!!
same problem here. nothing, absolutely nothing is easy in this hobby
@@dtaves how did you solve
@nitefieldfpv i believe i bought a balance lead adapter and plugged it in to get power. However keeping it powered and not cooling it is risky. But then i crashed it a while ago and havent been able to get it to work
@@nitefieldfpv flywoo has one
The app sux . I have to re sinc up each gopro everytime . This one is very much harder because of what it is . Good luck girls n guys
Even when I have the Hero 9, and interested in features of the Hero 10 that just dropped, I still also want this geprc naked 8 for my cinewhoop🥲👌 life is hard🤣