If you're replacing the bearings you ALWAYS use sealed bearings not shielded. You never pound on any bearing using any metal hardened metal tools in order to seat your bearing. For grease for those of you asking NLGI #0 - NLGI #1 grease is needed, "check with manufacturer requirements". If the manufacturer doesn't provide information or the #0 and or number #1 grease isn't available in your area or the cost is out of range I do have a couple other options which will not harm your tool and can make the process possible at the same quality and effect, just a little more work is involved.
Hello, thank you very much for this great video, it has been very useful to me, because I had the same problem, and I disassembled the device, and verified that it was wrong with bearings, I liked it a lot
Not all grinders can be serviced like this, the green Bosch grinders has the bottom bearings into the plastic casing, they are cheap to replace. Good to see you repair a tool though, instead of just replacing, so well done!
Es una boludez, sin embargo admito que nunca le hice eso a mí máquina lo cual voy a proceder a hacer, éxitos y gracias por mostrar algo tan práctico que para unos es fácil y para otros no.
At my work electricians service them,but i was just curious how they do it,without disassembling myself actual grinder.Perhaps one day i might need to know it .All the best & thanks @@zana3587
Hey there, my battery grinder for some reason has started to loosen the flange nut right after I turn it on. What has possibly happened? Is it fixable with cleaning and greasing or something else? Thanks!
Hi - you have good information about (soma angle grinder) yes it is from china but i don't know about quality - but this angle grinder i buy it in 2006 and until now it is worked - maybe just this type are good
Thank you very much teacher for your encouragement - I didn't used any a special product - i use petrol (kerosene) to clean it - you can see (video 14) time 3:15 to 3:40 -
I also fix things on a certain level yet and I'm from a country where these tools costs way more than the salary of the users can handle. So repair is a must. I am amazed the uploader of this video can even acquire new part for this. I mean the exact sizes of the of the bearings and the screw. You would be more than lucky to find the exact part in my country. haha
मेरा ग्रँनडर तो चलताहै लेकिन गरम हो जताहै क्या प्रोबलम है मेरा नमबर 96488 46591 प्लिज फन पर समझाए Please sir 2 minit ke leya plz mai aap ka intjar karnjua plz Thanks
If you're replacing the bearings you ALWAYS use sealed bearings not shielded.
You never pound on any bearing using any metal hardened metal tools in order to seat your bearing.
For grease for those of you asking NLGI #0 - NLGI #1 grease is needed, "check with manufacturer requirements". If the manufacturer doesn't provide information or the #0 and or number #1 grease isn't available in your area or the cost is out of range I do have a couple other options which will not harm your tool and can make the process possible at the same quality and effect, just a little more work is involved.
Excellent Video. Congratulations and Many Thanks.
Hello, thank you very much for this great video, it has been very useful to me, because I had the same problem, and I disassembled the device, and verified that it was wrong with bearings, I liked it a lot
+Diego Decorrientes welcome any time
Diego Decorrientes
+Loise Marck Welcome man any time
This is what I'm looking for, very nice demo on repairing angle grinder. Regards from GOLDEN WORKS TV!
thank you
Excelente vídeo, gracias saludos
gracias Señor
Para acomodar los cables de pulidora d28402
Not all grinders can be serviced like this, the green Bosch grinders has the bottom bearings into the plastic casing, they are cheap to replace. Good to see you repair a tool though, instead of just replacing, so well done!
Thank you
Radman SA
lo que estaba buscando,grscias ahora ya sé
Bienvenido
Great Video, wonderful information.
Thank you sir . I am sorry for my late . Sometimes I forget the response
Dahen Zana, it's always better late, than never, to answer some one comment, O.K.
if you don't have the presser, just put a small wood piece or plastic between the bolt and your smasher...to prevent damaged to the bolt's head...
Thank you for your info
@@zana3587 www
Great work.
MOHSIN BAJWA Thank you
Bravo daher zana
thank you
Es una boludez, sin embargo admito que nunca le hice eso a mí máquina lo cual voy a proceder a hacer, éxitos y gracias por mostrar algo tan práctico que para unos es fácil y para otros no.
gracias
Спасибо за абзор
добро пожаловать
Help full indeed,thanks !
Thank you sir i hope it's helpful for you
At my work electricians service them,but i was just curious how they do it,without disassembling myself actual grinder.Perhaps one day i might need to know it .All the best & thanks @@zana3587
You welcome sir, any time
Good work
SANIL VA Thank you
fantastic very well done
Thank you sir
عمل متقن وممتاز
Welcome
👍👍👍👍👍👍👍👍👍
thank you sir
excellent!!!!!
Thank you
Very goooood
Thank you sir
Cool !
Thank you lady
Good video. Use mallet cleane Sw area
+Srirama Murthi Thank you
تسلم مهندس
شكرا
Muy buen video
Thank you
Hey there, my battery grinder for some reason has started to loosen the flange nut right after I turn it on. What has possibly happened? Is it fixable with cleaning and greasing or something else?
Thanks!
👍👏
ok
which grease is best used for lubricating the gears on the grinder
I don't know which brand is better . But i use normal cars grease
Moly grease high pressure
Look for high temp.grease.
Great
thank you sir
Thank you share👍🏻
thank you sir
which Grease did you use ? is Blue grease suitable for Angel Grinder ?
Thank you sir
Welcome sir
Great video! What kind of grease did you use?
any kind but good quality
Dahen Zana so can I use the same grease I use for my vehicles suspension parts such as u joints, upper and lower ball joint’s, wheel bearing, etc?
Good job
thank you sir
very good job
thank you
Thanku sir
Mithun Mandal You welcome man
أحسنت عمل رائع
اشكرك اخى العزيز
soma are made in china, i hope the new bearings are of better quality than the old ones, it does not look very old to have worn so badly.
Hi - you have good information about (soma angle grinder) yes it is from china but i don't know about quality - but this angle grinder i buy it in 2006 and until now it is worked - maybe just this type are good
Stary... Wirnik spadł ci na podłogę....
Part of engine fall on the floor ! Pal
In time bar 10:20 i connect the armature by wire with the table .its Not visible to camera
Hola. Que medida la balineras? Gracias
why machine is heating when new armature is repaleced please reply
Sorry
Donde comprar las cunas para las pulidoras
+maria cordoba Miss Maria Can you write in English because I do not understand you sorry
How did you clean the old grease? did you used a special product? Thanks for the great video, very informative ! It remind me my school days :)
Thank you very much teacher for your encouragement - I didn't used any a special product - i use petrol (kerosene) to clean it - you can see (video 14) time 3:15 to 3:40 -
great thanks ! Be sure I will watch your future video - very nice to see people repairing stuff - Cheers
great thanks to you too - you are a great teacher
clean it with kitchen towels, finally use an air compressor
Gasoline in a pan and brush it out old school. Or a good degreaser
👏👏👏👏👏👏👍
Thank you
Nice video
What grease you use
Thank you sir. any kind but good quality
@@zana3587 thanks
Maybe you should spend some money on some basic tools. Using hammer directly onto the new bearing, is a bad deal.
Thank you for your info
what is the small metal looking part?
which small metal ? can you point in time bar?
If you are referring to the half moon shaped part, it is called a woodruff key.
Thank you for your info
Put bearing in freezer overnight and it will just drop in
Paul Cluer Thank you
good video but dont hit bearings in and remove some grease and clean the whole machine. buy a press or something and torque to specs..
Ryan Sardjoe Missier would a big vise with soft jaws work in place of a press? Or even a C-clamp with a wide solid smooth top over the lead screw?
Sure, just buy a press bc it's that simple.
thank you
Sure fire way to shorten the bearing life by at least 80%, HAMMER IT!
ok
No how lightly he was hitting it and just on both races it would do nothing to it if he slipped and hit just the seal then yes but No
I have black&decker grinder so which barring I can use brother please tell me.
Written on bearing . you must open it , then you can see the number on it
@@zana3587 ohh my dear.barring is fully broken how can I see it.
Thanks sar
thank you
What size bearing?
6001z
تسلم ايدك والله عندى صاروخ بس ضعيف الحل ايه
ربما يكون العطل فى الملفات
انا عندي مشكله الصاروخ وهو شغال الصتوانه بتقف ايه المشكله
عندي مشكله في صروخ في مشكله صروخ شغال الصتوانه بتقف
what fat do you use? brand and compound that contains that fat, to see if I can get it in my country, Mexico. thanks
any good brand
Brother what is the barring number???
It's 6001
I can't open the head screw it very tied how to open
hitting on the head of the screw using screwdriver
what the name of thing that you say don't lose it?well i lose it,where can i buy it.
no idea sorry sir
woodruff key
Parabéns
Obrigado senhor
bhi hi max grander ka gear box nahi khull raha koi bta sakta hai kaise khulega
When to regrease grinder
+Soldier1287 Does not depend on when! But depends on the duration of use
ok
High temperature grease is ok?
grade 2 and is red.
How clean out old grease?
+Soldier1287 Only with gasoline
ok
Подскажи название смазки /// удачи каналу
можешь показать мне шкалу времени
@@zana3587 12: 17
ar.aliexpress.com/item/4000589115023.html?spm=a2g0s.8937460.0.0.5d662e0e1QxeTa
I SEND THE LEINK
thank you sir
J
!
I could not do that service of yours. I would buy a new makita! I am giving you a like for your heroic service. Tool was not worth it!
As you like
I also fix things on a certain level yet and I'm from a country where these tools costs way more than the salary of the users can handle. So repair is a must.
I am amazed the uploader of this video can even acquire new part for this. I mean the exact sizes of the of the bearings and the screw. You would be more than lucky to find the exact part in my country. haha
@@N1Zer0 where are you living? 🙂
12:32 i lost the little pin what should i do ???
1 you can made another one 2 buy it in the internet but its expensive 3 you can find it in broken angle grinder
@@zana3587 thank you brother for the help , very much appreciated 🙏
Like just because I care about the tool.the execution leaves much to be desired.
ПАВЕЛ ЕРЕМЕЕВ good job
All grinder same barring use
No
विडयो बोलते हुवे बनाये
धन्यवाद
Contacto
por qué
.
thank you
मेरा ग्रँनडर तो चलताहै
लेकिन गरम हो जताहै
क्या प्रोबलम है
मेरा नमबर 96488 46591
प्लिज फन पर समझाए
Please sir 2 minit ke leya plz mai aap ka intjar karnjua plz
Thanks
Lot of work just to change a bearing. Rather go buy a new grinder. £21 at screwfix.
This work cost me a few bucks
Dont watch diy videos then! Watch how to buy new tools instead!
That's just stupid.