Thanks bro. But almost every engine use a different type of compressor. Example a Toyota 1nz engine compressor fit different from a Nissan HR compressor
@@darenbhalai9872 Toyota Yaris ProBox axio belta that use the 1NZ engine. Use the same compressor most of the time is just the pulley make the difference
I did change my ac compressor for toyota axio 2007 along with changing the dissicant in the dryer and replace with another solenoid compressor brand new, ac cool for 2 days and stopped working again. Can anyone comment as to what may have happened.
If your AC was working properly but only the bearing was making a lot of noise...you did NOT have to remove the ac compressor and discharge the system to change that pulley. It can be done with the ac compressor attached to the car. You did too much work.
Thank you for comment sir. I clearly understand what your trying to say. This is why a lot of technicians damage customer AC compressor because they are trying to save refrigerant (ac gas) and break off the customer compressor shaft neck. That is where the clip lock the compressor bearing. When the technician do so they only inconvenience the customer to buy a new compressor at their expense when it is the technician's fault. Why the compressor shaft Neck break off: (1). Once the compressor bearing is damaged it would normally get tighter on the shaft neck . That would therefore mean when it gets tighter the pulley would then have to come off straight. Failure to do so will damage the compressor. So when a technician try to remove the compressor on the car 70% chance that the shaft neck will break off given the lack of space. When the compressor is removed and placed on a work table it easier to monitor. (2). Once the compressor bearing is damage it always best to remove the compressor and inspect inside of it to see the condition if it's wise to replace the bearing or change the compressor itself. We don't like to cheat the work so we dweet the right way so the customer happy😁
I'm not hating but this is stupid, video make no sense, you skip out all the necessary part, you don't remove the bearing and install a new one you replaced it instead. Plus you didn't show the audience how you remove the pulley. Therefore, video is trivial. I do all that at Jay's AC and refrigeration works at passage fort drive portmore
It's obvious that you don't watch the video properly. I never say a new bearing. I say used bearings. Please note this is not a how to do video so don't criticize my video to promote your workplace . This is just a video to promote our work so that mean it will not show you all the information
@@KirksCoolAirAutoTV great job...My axio engine is 2zr but my compressor don't work well the ac guy say the switch not working properly..so I buy a new compressor a 2az compressor one with clutch and they conver it but working properly but thing different is when I stop and the ac compressor keep chip in and out I feel the vibration don't know if something else can done to fix that or it's because a different compressor convert?
@@KirksCoolAirAutoTV oh but its fine when am driving you don't feel it I was thinking probly bkz the original one did have the built-in switch and this one they convert a switch on the out side with a relay.
How did you take it apart with what tools and how exactly I want to change the bearing too
Just wanna to ask the details why you change a cover hub?thanks
Like the video but wanted uou to show how disassemble everything
Nice one great job keep these informative videos coming
Respect bro remember to subscribe to the channel and share the video
Good video appreciate
@@alexplainlater9713 👍
Very informative keep it up
Yes Kirk, nice video again but I ha e a question, does all those vehicles uses the same type of compressor?
Thanks bro. But almost every engine use a different type of compressor. Example a Toyota 1nz engine compressor fit different from a Nissan HR compressor
@@KirksCoolAirAutoTV I know that, I was referring to the Toyota types of vehicles. Probox, axio, yaris, rav4...etc
@@darenbhalai9872 Toyota Yaris ProBox axio belta that use the 1NZ engine. Use the same compressor most of the time is just the pulley make the difference
@@KirksCoolAirAutoTV just checking still, but if I have any issue it's you who I'll be finding. My car has in a 2nz engine though.
No problem bro you are welcome anytime
Hey Kirk , does a bad bearing damage the compressor after a while?
Yes davis it can damage the compressor
How much to do this on a 2014 probox
I did change my ac compressor for toyota axio 2007 along with changing the dissicant in the dryer and replace with another solenoid compressor brand new, ac cool for 2 days and stopped working again. Can anyone comment as to what may have happened.
If your AC was working properly but only the bearing was making a lot of noise...you did NOT have to remove the ac compressor and discharge the system to change that pulley. It can be done with the ac compressor attached to the car. You did too much work.
Thank you for comment sir. I clearly understand what your trying to say. This is why a lot of technicians damage customer AC compressor because they are trying to save refrigerant (ac gas) and break off the customer compressor shaft neck. That is where the clip lock the compressor bearing. When the technician do so they only inconvenience the customer to buy a new compressor at their expense when it is the technician's fault. Why the compressor shaft Neck break off:
(1). Once the compressor bearing is damaged it would normally get tighter on the shaft neck . That would therefore mean when it gets tighter the pulley would then have to come off straight. Failure to do so will damage the compressor. So when a technician try to remove the compressor on the car 70% chance that the shaft neck will break off given the lack of space. When the compressor is removed and placed on a work table it easier to monitor.
(2). Once the compressor bearing is damage it always best to remove the compressor and inspect inside of it to see the condition if it's wise to replace the bearing or change the compressor itself.
We don't like to cheat the work so we dweet the right way so the customer happy😁
How can i locate u
Kingston jamaica call us (876)447-7703
Seme as camary
I'm not hating but this is stupid, video make no sense, you skip out all the necessary part, you don't remove the bearing and install a new one you replaced it instead. Plus you didn't show the audience how you remove the pulley. Therefore, video is trivial. I do all that at Jay's AC and refrigeration works at passage fort drive portmore
It's obvious that you don't watch the video properly. I never say a new bearing. I say used bearings. Please note this is not a how to do video so don't criticize my video to promote your workplace . This is just a video to promote our work so that mean it will not show you all the information
@@KirksCoolAirAutoTV great job...My axio engine is 2zr but my compressor don't work well the ac guy say the switch not working properly..so I buy a new compressor a 2az compressor one with clutch and they conver it but working properly but thing different is when I stop and the ac compressor keep chip in and out I feel the vibration don't know if something else can done to fix that or it's because a different compressor convert?
@@jahbless3904 greeting brother thanks for the comment it sound like the compressor never fit properly
@@KirksCoolAirAutoTV oh but its fine when am driving you don't feel it I was thinking probly bkz the original one did have the built-in switch and this one they convert a switch on the out side with a relay.
@@jahbless3904 How many switch your original compressor use?