Well, I for one am grateful to have this washing machine because I did not have any washing machine for over a year. If I wanted to wash my clothes without having to go to a laundry mat I had to wash them by hand, which would make the skin on my hands raw and painful. What has worked for me with this machine: put the liquid soap in first, then the clothing; pre-spot and rub any stains out as much a possible before adding them to the load, once there is enough water according to the sensor, open it and push whatever has not gotten wet down (I think that may affect the sensor and it will add more water to the load, the deep clean cycle takes too much time for my liking); be aware of when the rinse cycle begins and add the fabric softener then - or - much easier, after the entire cycle ends run the rinse cycle again with the fabric softener. I don't know how it works for others, but I read that adding vinegar to your wash really helps get them clean and strong odors out. That it does. But I think it caused my previous washing machine to slowly fall apart by disconnecting things that were glued in because hot vinegar is a really good way to remove sticky substances. It was a great machine and got things really clean, not old, but it got a great deal of use with hot water. I'll never use vinegar again in any washing machine, hot or cold water. Anyway, thanks for the video, I've never taken the time to watch my laundry being washed. It did help. Thank you.
Thinking this will be my next washer and the dryer set that comes with it in next few years. We have a Maytag washer and dryer and set, but the washer sometimes has problems spinning out the clothes plus the dryer has problems drying properly when drying clothes most of the time, but it’s probably getting close to buy a new set sooner than later
I own this washer too...I gave away my Maytag cause it bounced around too much...but I wish I kept it. For those of you who hv this 100 series Kenmore, hopefully it's hooked up next to a sink, or water faucet do you can attach a foot hose which are sold at any hardware store, after you start any cycle, wait till you hear the water stop filling, then either push pause, or just lift the lid and fill your top loader to the desired amount of water you want..don't over fill it..at least till the notch below the top flat part it where I always full mine. I know it's time consuming, but hey, I remember my mom washing clothes in my grandmother's old machine in the early 70's and it's better than a washboard. Life is short, I bought mine with proceeds from a Superbowl win in 2015...Aloha
We have the 2019 model of this washer, I have never missed my Samsung front load so much. I don’t hate it but I don’t love it either. We lost our home to a house fire back in 15. We (well we have always done this) live on a tight budget now. When our washer broke we had no choice but to buy this one.
To increase water level in the Kenmore 100 series, just turn the switch from normal to " DEEP WASH". I just found that out after months of searching and dismantling my unit
Thanks for the video. I and my husband always liked Kenmore brand and got this washer without thinking nor research. I really regret it now, because no matter how big the load is, the deepest the water level gets is like 12 inches. Saving the water is ok, but if the clothes needs good rinsing, they need more water, I believe.
I have the same washing machine one problem is you are selecting the same cycle second reason is if you put on a different cycle and if your clothes are not getting cleaned, you must add soap people like you don’t even know that soap exist!
Something else I learned about this machine, I think it may help in the long run, to run the machine empty with bleach (like you are supposed to to clean it every now and then. Maybe because it doesn't use much water and because I use fabric softener in the rinse cycle when I wash, the plumbing doesn't seem to not drain as quickly as it used to. I don't know but I do it as a precautionary measure every now and then. If have done that by running the machine empty using just bleach, and I have removed the drain hose from the wall drain pipe (not from the washing machine) and poured boiling water with bleach in it. This took care of the leaking (I had in the laundry room which was caused when the water didn't drain through the house drain pipe as quickly as it was leaving the washing machine) immediately. Maybe I was using too much soap and or fabric softener. I don't know, but I'm pretty sure it was something I was doing wrong since I am not mechanically inclined. And I'm sure I was just using too much vinegar, like I did when I would use it also to clean the outside of the refrigerator and now I have little chips and rust spots on the paint. I guess I just wasn't rinsing the vinegar off well enough. I'm learning though.
So me and my roommates have been having soiled clothes after the wash cycle and drain spin issues. The clothes come out dirtier then when they go in. The machine will not switch to the drain spin cycle at all. However after checking the valves I discovered maintenance men who installed our washer at our apt did not open the valves (hot and cold) completely. I’m waiting on a load now to see if that improves the current soiled wash situation. I’ll keep you all updated.
You have to hold the button for approximately 3 seconds and then release the button and wait then it should unlock. I learned you have to be patient with it or it won’t work. Also if that fails unplug it for about 2 mins then plug it back in. Give it a moment and if it doesn’t unlock on its own repeat the first step again. Hope this helps.
i had to pause it when it was rinsing and wait about 30-40 seconds for the lid to unlock and then I added the fabric softener 🤷🏻♀️ idk if there’s an easier way because it’s annoying to be waiting next to the washing machine.
I apologize if I can't message some of you back directly. The video was for learning purpose only. Not for it to be a demo of things to do per say. Please unless you know what you are doing or have experience working on them just let the machine do its job. Thanks :)
I believe if you turn the fare right nob where it reads normal casual ect.. Turn it to the left from center on normal turn it counter clockwise just before it is on Heavy Duty. That should do it. The washer also has a sensor that tells it what size as well, it is just like a front load washer but it's a top load, so it doesn't use as much water as a normal washer. Are your clothes coming out not as clean as you would like?
Does yours do the same as mine? It is a totally different machine than any I have ever had, but it does get my clothes cleaner than any other washer that I have ever had..
There is no way to do a pre soak with oxyclean so I find it frustrating. I have always soaked my whites overnight in hot water and oxyclean to make sure the come out really white.😟😟
sure wish I had read these reviews before I purchased my can of waste. 3 weeks in and I am having each issue I read. I do not want to go through this anymore bye bye Kenmore. I loved my GE and I mean I LOVED IT for 16 years it worked without needing repairs.
Sdot Duncan I just don’t get how so many people are having issues with the washer. I haven’t had any problems not one. And it’s been the best washer I’ve ever owned so idk. But it’s the case with everything, you get good ones and bad ones. I fortunately got a good one I guess. I’m sorry you haven’t had a good experience with it. But do know it is a good washer just probably got a bad one idk. Again sorry for your bad washer. Hope you can get one to your liking.
Sdot Duncan I agree . My husband got me one of these at a sears store in Mac Allen Texas in march of 2015 and it stood in it's box in my living room till this 21st of December 2017 . Almost 2 years . I hated it on sight and I have used it 3 times and I despise it even more . Have a Kenmore Elite Total Care System with water level, rinse and speeds options that I totally love . I just want a machine that I can control .
I have had my washer for almost 5 years now and no issues what so ever. People get bad stuff sometimes. I’ve bought other stuff that people swore was great but I got the crappy one. It happens. Sorry for your frustration. I hope it doesn’t keep frustrating you. Have a great day
I have this same machine my model number stickers and serial numbers have been removed ..trying to order a new drain hose ..sears repair tells me they need the model number of the machine to help me...could you please share the model number of the machine
My series 100 kenmore does this thing where you can here the timer moving but the spin and rins and spin and drain acts up. honestly a towel or pants shifting should not cause the wash cycle to stop what is going on if i pause and cancel and move to the spot on the timer/control that says spin and rinse/ spin and drain it kinda acts better but i must pause it and un pause a few times.
we have this washer approximately 6 months old and it does the was but then when u go throw the clothes in the dryer they are still soaked. so to spin the clothes out you have to have it on the drain and spin button and it fills with more water makes no sense I just want it to spin the remaining water
Went to take my clothes out to dry and notched there was still water in there and the lights weren't on, I've tried to reset it but it only makes a humming noise with no movement and the light don't come on, please help
I fixed it by disconnecting the control board from the housing and pressing the start button on the control board directly. I did not disconnect the wiring from the control board. I then reassembled. I plugged it back in and pressed start. It acted like it wanted to work but I knew it needed re-calibration. I followed the instructions to re-calibrate here. It works like new!!! "www.searspartsdirect.com/repair-guide/washer/how-to-replace-the-electronic-control-board-on-a-top-load-washer.html"
It’s the worst investment to put your money. It leaves white clothes horribly dirty. I have to keep opening the lid and close the lid in order to get it to fill up to a decent level. Who ever engineered this in my opinion purposely created it to confuse the consumer.
Esk K If you look at all the responses and how frustrated they are with this “energy efficient “ washer you will have to agree it’s a disaster. Not sure why you are defending this product
@@elizabethvillalobos8927 I just bought one and Kenmore should be ashamed of themselves saling junk never will I buy a Kenmore again they should be sued these washers aren't cheap
This is years later now. I just had the misfortune of moving into an apartment with this washing machine. How can I stop the cycle so I can soak clothes in it? Even with the lid open it drains!
What is the center portion for? You’re not to put detergent under the cap in the center? I’m renting a home that has this washer and I don’t know to put in the detergent and softener just in the clothes or in the center part? That’s what I’m looking for
Hey so me and my roommates have this same washer but when we do our laundry its going through the sense cycle and the first wash cycle and drains but after draining it makes a clicking noise and wont go any further, when it stops the clicking noise its first was cycle light flashes would you possibly know whats wrong?
Nasha M good question, how long have you had the washer and is this something that just started. It’s possible that the sensor it’s not working properly. If that is the case I would check with the manufacturer and see if they have any trouble shooting that can help. I’m sorry I really don’t know what else to do I have not had that problem
FYI the newer washing machines (with the fancy buttons and idiot lights) are total garbage. Next time get a used one with the pull out knob on CL or FB.
I have this same washer in my apartment. It is the worst. This mans clothes never got completely soaked nor did the clothes ever move from the top. What i call. ..not cleaned. I have never been able to havevthe water level ever get a full drum even with a load of king size sheets and towels...ever
Since it is a computer "sensor", I am not even going to try to figure out how to adjust the water level to my own liking. I do not want to have to pay a professional to come fix it and have them ask me "Well, what's wrong with it? What did you do? Oh no, you can't do that, that's going to take some time and money to fix. I don't work on the computer stuff, just the mechanical stuff." No thank you. Sometimes good enough is just that, good enough.
Just bought a house with this washer, when I run on medium, cool lights, normal and during the wash phase the clothes aren’t even fully submerged in water, is this normal?
My dark clothes are coming out with white residue on them. I’m using tide he turbo detergent, and using the settings above. We use a teaspoon and a half of soap cause we have soft water. This washer doesn’t rinse them properly. Any suggestions.
I have the same washer unit that came with my apartment unit however the tub looks loose and not close up like yours in the video. Could this mean an issue with the washer?
bamaboss99 I could not tell you without looking at it first. Maybe have someone take a look, someone who knows what they are doing and not just anyone.
Frank Borrego hey sorry I haven't gotten to making that video yet. Have had a lot of crazy things going on and just haven't made it yet. I will try and get it done, just wanted to touch base to let you know I have not forgot
Esk K Not a problem whatsoever bud. I'll check it out now, thank you! Also, sub up to my page so you can keep up with what I'm up to. And I promise to do the same. :)
My washer just started making a loud clunking sound, sound and feels like the drum is going to come out the side of the washer. Any ideas whats wrong with it?
CHARLESF55 you should be able to remove the cap on the center of the agitator and there is a nut, then gently pull it up not off just up enough to reach under to get the coins. Hope that helps.
Wilbur Tabácskó sorry so long to reply haven’t been online in a few months. I’m sure you fingered it out on how to get your coins removed by removing the cap on the agitator and unscrew the metal nut/bolt.
Eva M I don't know what to tell you other than you got a bad one and I would take it back if possible or exchange it. My washer runs great and I haven't had any issues with it. Sorry your having these issues.
@@eskk2169 I’ve tried the lid lift reset. All the other cycles work fine. Just doesn’t go to the last spin cycle and clothes are saturated. When I switch to spin/drain it pumps all the water out and spin drains fine. Just won’t automatically
Terrible Appliance avoid at all cost I'm sure we're all here commenting because we have one and it's trash... unable to wash four pair of pants without leaving one dry and soapy(work pants not yoga pants). Whoever designed this is probably been demoted
isaac tapia people aren’t here to complain. Not all of these washers are bad. You can get a bad one or a good one it happens with all appliances believe it or not. Just because yours doesn’t work doesn’t mean others don’t. I still have mine and it works great. You just have to know the run down on it. I’m sure you just got one that isn’t good but don’t blame them all for one. That’s like saying all Fords or Chevys are garbage, not so. I don’t care for Ford but I do know they make some great vehicles.
Jose Canosky TRD I don’t know exactly what’s the issue with yours but to rest if the lid is locked you have to hold the start/stop until you hear it click the release lock for the lid. I hope that helps.
Once they reset it by opening and closing the lid and started to work. I do not remember how to follow the steps. it was that the light went out and gave an error. Thanks.
It barely agitates and sometimes if I don’t get my clothes out right at finish I like to run them through the rinse again.I had to run them through the hole cycle.Put some on the soak and it filled up and run back out was no soaking to it.
Well, I for one am grateful to have this washing machine because I did not have any washing machine for over a year. If I wanted to wash my clothes without having to go to a laundry mat I had to wash them by hand, which would make the skin on my hands raw and painful. What has worked for me with this machine: put the liquid soap in first, then the clothing; pre-spot and rub any stains out as much a possible before adding them to the load, once there is enough water according to the sensor, open it and push whatever has not gotten wet down (I think that may affect the sensor and it will add more water to the load, the deep clean cycle takes too much time for my liking); be aware of when the rinse cycle begins and add the fabric softener then - or - much easier, after the entire cycle ends run the rinse cycle again with the fabric softener.
I don't know how it works for others, but I read that adding vinegar to your wash really helps get them clean and strong odors out. That it does. But I think it caused my previous washing machine to slowly fall apart by disconnecting things that were glued in because hot vinegar is a really good way to remove sticky substances. It was a great machine and got things really clean, not old, but it got a great deal of use with hot water. I'll never use vinegar again in any washing machine, hot or cold water. Anyway, thanks for the video, I've never taken the time to watch my laundry being washed. It did help. Thank you.
Thinking this will be my next washer and the dryer set that comes with it in next few years. We have a Maytag washer and dryer and set, but the washer sometimes has problems spinning out the clothes plus the dryer has problems drying properly when drying clothes most of the time, but it’s probably getting close to buy a new set sooner than later
I own this washer too...I gave away my Maytag cause it bounced around too much...but I wish I kept it.
For those of you who hv this 100 series Kenmore, hopefully it's hooked up next to a sink, or water faucet do you can attach a foot hose which are sold at any hardware store, after you start any cycle, wait till you hear the water stop filling, then either push pause, or just lift the lid and fill your top loader to the desired amount of water you want..don't over fill it..at least till the notch below the top flat part it where I always full mine.
I know it's time consuming, but hey, I remember my mom washing clothes in my grandmother's old machine in the early 70's and it's better than a washboard. Life is short, I bought mine with proceeds from a Superbowl win in 2015...Aloha
We have the 2019 model of this washer, I have never missed my Samsung front load so much. I don’t hate it but I don’t love it either. We lost our home to a house fire back in 15. We (well we have always done this) live on a tight budget now. When our washer broke we had no choice but to buy this one.
To increase water level in the Kenmore 100 series, just turn the switch from normal to " DEEP WASH". I just found that out after months of searching and dismantling my unit
Thanks. I did not know and will try with my next loads!
Thanks for the video. I and my husband always liked Kenmore brand and got this washer without thinking nor research.
I really regret it now, because no matter how big the load is, the deepest the water level gets is like 12 inches. Saving the water is ok, but if the clothes needs good rinsing, they need more water, I believe.
momomin0218 I haven't had any problems with mine at all I got it probably a week before I did the video and it's doing what it's supposed to do. Sorry
Do you get paid for your hype and optimism? This machine is crap! You can read stories of disappointments all over Internet.
I have the same washing machine one problem is you are selecting the same cycle second reason is if you put on a different cycle and if your clothes are not getting cleaned, you must add soap people like you don’t even know that soap exist!
I have this washer and it's a fucking piece of shit. Glad it was free
Something else I learned about this machine, I think it may help in the long run, to run the machine empty with bleach (like you are supposed to to clean it every now and then. Maybe because it doesn't use much water and because I use fabric softener in the rinse cycle when I wash, the plumbing doesn't seem to not drain as quickly as it used to. I don't know but I do it as a precautionary measure every now and then. If have done that by running the machine empty using just bleach, and I have removed the drain hose from the wall drain pipe (not from the washing machine) and poured boiling water with bleach in it. This took care of the leaking (I had in the laundry room which was caused when the water didn't drain through the house drain pipe as quickly as it was leaving the washing machine) immediately. Maybe I was using too much soap and or fabric softener. I don't know, but I'm pretty sure it was something I was doing wrong since I am not mechanically inclined. And I'm sure I was just using too much vinegar, like I did when I would use it also to clean the outside of the refrigerator and now I have little chips and rust spots on the paint. I guess I just wasn't rinsing the vinegar off well enough. I'm learning though.
So me and my roommates have been having soiled clothes after the wash cycle and drain spin issues. The clothes come out dirtier then when they go in. The machine will not switch to the drain spin cycle at all. However after checking the valves I discovered maintenance men who installed our washer at our apt did not open the valves (hot and cold) completely. I’m waiting on a load now to see if that improves the current soiled wash situation. I’ll keep you all updated.
What button do you use to fill the washer all the way to the top, like the normal washer do
Deep Wash.
And it only fills it to a 1/3 full.
HOW CAN WE CHANGE THE WATER LEVEL ON IT.. MINE ONLY STAYS AT LESS THAN HALF FULL NO MATTER WHAT SETTING I PUT IT ON
Priscilla Moore read my blog next to yours...happy washing.... :)
Tomo San I’m trying to see where you commented about the water level. Any help on that?
@@puppet003 wheres your link?
Omggggg I'm having the same issue. Please someone helppppp!!
Mines too
You have to hold the button for approximately 3 seconds and then release the button and wait then it should unlock. I learned you have to be patient with it or it won’t work. Also if that fails unplug it for about 2 mins then plug it back in. Give it a moment and if it doesn’t unlock on its own repeat the first step again. Hope this helps.
how do you add fabric softener to the wash?
Did you ever find out how do to add fabric softener to the washer
i had to pause it when it was rinsing and wait about 30-40 seconds for the lid to unlock and then I added the fabric softener 🤷🏻♀️ idk if there’s an easier way because it’s annoying to be waiting next to the washing machine.
Use a Downey ball. You can use any liquid fabric softener in it. Dryer sheets are hard on the heating elements of your dryer.
I apologize if I can't message some of you back directly. The video was for learning purpose only. Not for it to be a demo of things to do per say. Please unless you know what you are doing or have experience working on them just let the machine do its job. Thanks :)
Hi can you get back to me tatybossita@gmail.com I need some help if you know about the washer
I made this video so people could see how it works not for people to try stuff and have issues I went through the steps to tell what not to do.
What?
How can you make it put more water, I noticed it puts little water and I think it's not enough for a good wash
I believe if you turn the fare right nob where it reads normal casual ect.. Turn it to the left from center on normal turn it counter clockwise just before it is on Heavy Duty. That should do it. The washer also has a sensor that tells it what size as well, it is just like a front load washer but it's a top load, so it doesn't use as much water as a normal washer. Are your clothes coming out not as clean as you would like?
Does yours do the same as mine? It is a totally different machine than any I have ever had, but it does get my clothes cleaner than any other washer that I have ever had..
It will do it all by itself so don't worry
There is no way to do a pre soak with oxyclean so I find it frustrating. I have always soaked my whites overnight in hot water and oxyclean to make sure the come out really white.😟😟
WHO I SELECT THE WATHER LEVOL
Mines does not fill enough water
sure wish I had read these reviews before I purchased my can of waste. 3 weeks in and I am having each issue I read. I do not want to go through this anymore bye bye Kenmore. I loved my GE and I mean I LOVED IT for 16 years it worked without needing repairs.
Sdot Duncan I just don’t get how so many people are having issues with the washer. I haven’t had any problems not one. And it’s been the best washer I’ve ever owned so idk. But it’s the case with everything, you get good ones and bad ones. I fortunately got a good one I guess. I’m sorry you haven’t had a good experience with it. But do know it is a good washer just probably got a bad one idk. Again sorry for your bad washer. Hope you can get one to your liking.
Sdot Duncan I agree . My husband got me one of these at a sears store in Mac Allen Texas in march of 2015 and it stood in it's box in my living room till this 21st of December 2017 . Almost 2 years . I hated it on sight and I have used it 3 times and I despise it even more . Have a Kenmore Elite Total Care System with water level, rinse and speeds options that I totally love . I just want a machine that I can control .
@@eskk2169 i here more bad reviews than good ones// worse washer i ve ever had..
I have had my washer for almost 5 years now and no issues what so ever. People get bad stuff sometimes. I’ve bought other stuff that people swore was great but I got the crappy one. It happens. Sorry for your frustration. I hope it doesn’t keep frustrating you. Have a great day
Esk K how do u know ? I have had most of my washes come out ok. Some smelled sour.
I have this same machine my model number stickers and serial numbers have been removed ..trying to order a new drain hose ..sears repair tells me they need the model number of the machine to help me...could you please share the model number of the machine
@@rhondaredbird it’s the Kenmore series 100 HE washer.
This washer sucks really bad. From the water level to the lid lock to the violent bouncing around. Trash. You must work for them.
My series 100 kenmore does this thing where you can here the timer moving but the spin and rins and spin and drain acts up. honestly a towel or pants shifting should not cause the wash cycle to stop what is going on if i pause and cancel and move to the spot on the timer/control that says spin and rinse/ spin and drain it kinda acts better but i must pause it and un pause a few times.
So cause the water level is low does that mean you can't do big loads?? Just moved in an apartment that has this and I have no idea what I'm doing.
Yes you can do big loads in there. The washer has a sense mode thats automatic and will adjust for you. Hope that helps.
we have this washer approximately 6 months old and it does the was but then when u go throw the clothes in the dryer they are still soaked. so to spin the clothes out you have to have it on the drain and spin button and it fills with more water makes no sense I just want it to spin the remaining water
Went to take my clothes out to dry and notched there was still water in there and the lights weren't on, I've tried to reset it but it only makes a humming noise with no movement and the light don't come on, please help
Mine just stopped working. No lights. Motor humming. It never filled up. This is only just over a year old!!!!!!
Cathi Lee that's not good. Sorry to hear it pooped out.
I fixed it by disconnecting the control board from the housing and pressing the start button on the control board directly. I did not disconnect the wiring from the control board. I then reassembled. I plugged it back in and pressed start. It acted like it wanted to work but I knew it needed re-calibration. I followed the instructions to re-calibrate here. It works like new!!! "www.searspartsdirect.com/repair-guide/washer/how-to-replace-the-electronic-control-board-on-a-top-load-washer.html"
i would use a fabric softner ball
I need to remove the agitator and I don't see any other youtube videos on how to do it.
It’s the worst investment to put your money. It leaves white clothes horribly dirty. I have to keep opening the lid and close the lid in order to get it to fill up to a decent level. Who ever engineered this in my opinion purposely created it to confuse the consumer.
Elizabeth Villalobos everyone gets a bad item. Mine I’ve never had issues with and I’ve had it for years. Sorry for your frustration
Esk K If you look at all the responses and how frustrated they are with
this “energy efficient “ washer you will have to agree it’s a disaster. Not sure why you are defending this product
@@eskk2169 lint lint lint tons of lint will not clean the clothes
@@elizabethvillalobos8927 I just bought one and Kenmore should be ashamed of themselves saling junk never will I buy a Kenmore again they should be sued these washers aren't cheap
This is years later now. I just had the misfortune of moving into an apartment with this washing machine. How can I stop the cycle so I can soak clothes in it? Even with the lid open it drains!
Usually to pause it you push the button for I think 3 seconds. I’ve since moved and left the house to my kids and they still use it. Hope this helps
@@eskk2169 that doesn’t work, but I can definitely understand why you left the washer
If the lid is lock press and hold the start/stop cancel button until it unlocks
Happy Easter to all of you
Happy Easter
What if when you press the start button and the light doesnt come on
I would look for a video of how to calibrate it. That should help.
my washer puts in a little water then soon after the water starts to drain out leaving the clothes wet n not washed help...
Krystal S can you walk me through from the moment you put the clothes in the washer so I can have a better idea of how to help if I can.
Where do you put the softener? And or do you. Just add it in the clothes? The agitator in the middle have holes at the bottom. Kinda weird.
Misha Hans add a fabric softener ball the one you put liquid in and it will do the rest.
The washer works great and it's supposed to use less water just like the front load washers do.
How do you add fabric softener to the washer
What is the center portion for? You’re not to put detergent under the cap in the center? I’m renting a home that has this washer and I don’t know to put in the detergent and softener just in the clothes or in the center part? That’s what I’m looking for
I just add a fabric softener ball. And use He detergent in it.
Hey so me and my roommates have this same washer but when we do our laundry its going through the sense cycle and the first wash cycle and drains but after draining it makes a clicking noise and wont go any further, when it stops the clicking noise its first was cycle light flashes would you possibly know whats wrong?
Sounds like something in the controls for the sensor are faulty possibly causing the noise. Was the washer yours or was it there when you moved in?
my washer kenmore series 100 it will fill with water and drain but doesn't wash, pls any idea how to fix it... thanks
Nasha M good question, how long have you had the washer and is this something that just started. It’s possible that the sensor it’s not working properly. If that is the case I would check with the manufacturer and see if they have any trouble shooting that can help. I’m sorry I really don’t know what else to do I have not had that problem
I had this washer since 2015, it was working fine, suddenly it stop washing
Nasha M your washer fills all the way with water?
This washing machine is the worst piece of garbage I've ever purchased.
Gotta put a lid strike in there with the door open
Cuándo prima la ropa la máquina da cantazo qué es eso ayúdame por favor
FYI the newer washing machines (with the fancy buttons and idiot lights) are total garbage. Next time get a used one with the pull out knob on CL or FB.
Lavadora kenmore series 100 no enjuaga ni exprime y marca luz se spine y locked encendida como puedo resolver?
This machine does not have a fabric softener dispenser, correct?
Max correct. I use a fabric softener ball.
I have this same washer in my apartment. It is the worst. This mans clothes never got completely soaked nor did the clothes ever move from the top. What i call. ..not cleaned.
I have never been able to havevthe water level ever get a full drum even with a load of king size sheets and towels...ever
Hi, my washing machine is the same, i do not know how to apply downy. i do not want to stain fue fabric. ¿where or how it is applied?
I use a downy ball to add my fabric softener, it quick and easy. If you don't have one I would suggest getting one, well worth it. Hope that helps.
Ive had this washer for years. No problems but how do I do a quick wash?
I guess this washer is not modern enough to have the features😢
Since it is a computer "sensor", I am not even going to try to figure out how to adjust the water level to my own liking. I do not want to have to pay a professional to come fix it and have them ask me "Well, what's wrong with it? What did you do? Oh no, you can't do that, that's going to take some time and money to fix. I don't work on the computer stuff, just the mechanical stuff." No thank you. Sometimes good enough is just that, good enough.
Just bought a house with this washer, when I run on medium, cool lights, normal and during the wash phase the clothes aren’t even fully submerged in water, is this normal?
Yes, it adds as it washes.
My dark clothes are coming out with white residue on them. I’m using tide he turbo detergent, and using the settings above. We use a teaspoon and a half of soap cause we have soft water. This washer doesn’t rinse them properly. Any suggestions.
i have the same washer and mine just stopped on the wash cycle it hasnt moved. how do u fix that problem?
I would start off by pressing and holding the cancel button until it unlocks. You might have to start the load over again. Hope that helps
I have the same washer unit that came with my apartment unit however the tub looks loose and not close up like yours in the video. Could this mean an issue with the washer?
bamaboss99 I could not tell you without looking at it first. Maybe have someone take a look, someone who knows what they are doing and not just anyone.
Wow so smart
ESK K, do you have any videos of it washing with the lid open? Full cycles maybe... Im very interested in watching how it washes! :)
Frank Borrego I don't have any no. I could try sometime this week.
That would be awesome dude! Any full cycle would be fine, Im super curious on how it washes! Remember, hold the phone side ways for a full view! :D
Frank Borrego hey sorry I haven't gotten to making that video yet. Have had a lot of crazy things going on and just haven't made it yet. I will try and get it done, just wanted to touch base to let you know I have not forgot
Frank Borrego video is up of the washer doing a load with the lid up. Sorry it took so long.
Esk K Not a problem whatsoever bud. I'll check it out now, thank you!
Also, sub up to my page so you can keep up with what I'm up to. And I promise to do the same. :)
My washer just started making a loud clunking sound, sound and feels like the drum is going to come out the side of the washer. Any ideas whats wrong with it?
It's your suspension springs.
One of 4 either came off or is broken.
It's an easy fix.
You tube will show you how.
I fixed my neighbors washer.
Can you help me why doesn't fill more water turn of the sensor
How long have you had this issue?
@@eskk2169 i want more water but I don't know how to turn off the sensor mode or if that's possible at all thank you 😊
Mines ONLY ALWAYS HALF LOAD, HOW DO YURN ON FOR FULL LOAD OF WATER, MY DOOR IS LOCK WITH RED LIGHT ON, WHAT TO DO...HELP
I just bought one it locks how do I add fabric softtner
Latonya Morrell I use a fabric softener ball. That is the way to go.
We had a few coins get stuck inside it. How can i get them out??
CHARLESF55 you should be able to remove the cap on the center of the agitator and there is a nut, then gently pull it up not off just up enough to reach under to get the coins. Hope that helps.
I can just pull up on the agitator and it comes out.
Wilbur Tabácskó sorry so long to reply haven’t been online in a few months. I’m sure you fingered it out on how to get your coins removed by removing the cap on the agitator and unscrew the metal nut/bolt.
Do the whole inside suppose to move
Yes
This washer stains my clothes with what looks like grease stains on ALL my clothes and i don’t know how to get those stains out!!
Kamhyri Patterson THANK YOU SO MUCH IM GOING TO TRY IT SOON! I hope it still works even after i already dried my clothes!!!
It might be the actual detergent, since you have to pour it directly onto the clothes - very poor design !
in 40 years it's the worse washer I got . Level water problems and to wet for the dryer.
Eva M I don't know what to tell you other than you got a bad one and I would take it back if possible or exchange it. My washer runs great and I haven't had any issues with it. Sorry your having these issues.
Esk K thank you so much . But I live in Tx
Eva M hopefully you will be able to get something more to your liking. :)
@@user-od6wt4bw4s I have this one too and it's been nothing but problems but what does living in texas have to do with taking the washer back??
How do you find the filter?
There are 2 crescent-shaped Fine Mesh plastic lint filters in the bottom of the wash basket, under the agitator.
Not spinning out last cycle any help?
Have you tired doing a reset on it yet?
@@eskk2169 I’ve tried the lid lift reset. All the other cycles work fine. Just doesn’t go to the last spin cycle and clothes are saturated. When I switch to spin/drain it pumps all the water out and spin drains fine. Just won’t automatically
@@eskk2169 I’ve tried the lid lifting after unplugging
Never I can cancel the cycle if its necessary, even if desconected . the washer continue
the washer starting washing but then it stop how do i fix that
Chris Romero can you go into detail on what led up to it stopping?
Terrible Appliance avoid at all cost I'm sure we're all here commenting because we have one and it's trash... unable to wash four pair of pants without leaving one dry and soapy(work pants not yoga pants). Whoever designed this is probably been demoted
isaac tapia people aren’t here to complain. Not all of these washers are bad. You can get a bad one or a good one it happens with all appliances believe it or not. Just because yours doesn’t work doesn’t mean others don’t. I still have mine and it works great. You just have to know the run down on it. I’m sure you just got one that isn’t good but don’t blame them all for one. That’s like saying all Fords or Chevys are garbage, not so. I don’t care for Ford but I do know they make some great vehicles.
How do u unlock lid
Latanya King I put my reply in the comments section for you. Hope it helps. Let me know how it goes
Cómo la programo
Can,t find the switch to let the water run
Danny Goode what do you mean, What switch to make the water run?
Hi, how I do reset?
Jose Canosky TRD I don’t know exactly what’s the issue with yours but to rest if the lid is locked you have to hold the start/stop until you hear it click the release lock for the lid. I hope that helps.
Once they reset it by opening and closing the lid and started to work. I do not remember how to follow the steps. it was that the light went out and gave an error. Thanks.
Keep it moving don't buy, the worst head ach
I just bought this washer and it is the worst.
Tonya Kay why do you say it’s the worst?
It barely agitates and sometimes if I don’t get my clothes out right at finish I like to run them through the rinse again.I had to run them through the hole cycle.Put some on the soak and it filled up and run back out was no soaking to it.
This washer sucks
High efficiency means too little water and dirty clothes.
The
This washer sucks.