Think she’s a little top heavy and that’s why there is a bit of a wobble. But best lathe build I’ve seen, so refreshing to see a large build that doesn’t need a lathe to make it. Must have taken you a long time. Great work full stop, end of. Brilliant! Liked and subscribed
I worked in machine shops for 40 years. I never used gloves when operating machinery with spinny parts! Drills, lathes, mills. I worked with a guy that lost half of his hand because of a glove. If the pillow bearings go bad, how will you change them? Spindle welded at both ends.
He was very good friend, it takes a lot of work I imagine, whoever watches the video thinks it is easy, but in reality you get to do it, it gets complicated.
Se que es muy difícil. Soy militar jubilado y nunca trabajé, ni estudié en ésta área, pero me atrae. Seguí otro camino, comercio y administración pero no era lo mío. Me hice militar más por necesidad que por convicción. Me jubilé hace casi 10 años. En la milicia estudié y aprendí algo de Inglés. Estudié y fui profesor en el área de Inglés, pero como la universidad del Ejército en la que estudie, en sus inicio había sido centro de capacitación técnica en todo lo relacionado a herrería, siempre me daba mis escapadas por los talleres y deseaba aprender, pero estaba inscrito en el área de la Electrónica y Comunicaciones. Me gusta algo enseñar, pero me gusta mucho más aprender. Tengo un cuarto repleto de libros de todo tipo. Me fascina la carpinteria, algo de la construcción, electricidad y electrónica algo aprendí, y mi tendencia a la implementación de herramientas. Estoy instalando un taller... aún es solo para uso de instrucción...personal...
When you weld thick plate like that especially a but weld leave a gap the width of the bare metal of the rod your using between the plates I was a welder for 30 odd years. Amazing work by the way I have wanted to do something similar for years.
Seen a few af these “home made” builds but most of them gave lathes that only turned but had absolutely no precision. This looks great! Very very nice job, hope to see a lot more of your great work with mostly readily available materials. Thanks for sharing👍🏻
Good machine! You're doing fine! BUT! NEVER work with gloves on a lathe unless you want to lose your hand! Do not stop the chuck with your hands! All workers know these rules! Observe safety precautions!
So far your home made lathe machine is the best on YT, precise work, good and heavy built for last, but one thing I noticed about 3 pillow bearings, they are trapped at their location without the chances for replacement, you need to cut the shaft to take them out, over all you are good and your lathe is perfect example of homemade machines with basic available tools, I need to watch your video for more than couple of times to learn things of building one for my shop and my hobby related works, thank you for sharing your experiences.
Sorry for the late reply The problem you're worried about, I fixed it but I didn't do it on youtube, if you look carefully, you'll see the fix in my next clip. Thanks for watching
Es un hermoso trabajo, me encanta, pero tengo una duda con los tres soportes del husillo, ya que en muchas maquinas solo he visto solo uno en cada extremo.
You may want to see if you can get some housings made for taper roller bearings. Preloaded and well-lubricated, they should be significantly better than pillow block bearings.
Good job. I see only 2 mistakes. 1. You weld both sides and U cant change bearings without cut. 2. You use a metric thread not trapezoidal thread. Metric can stuck. Except that is nice.
Sorry for late reply. I have fixed the shaft that is welded on both sides. and there is a project that will put the taper bearing but haven't had time to do it yet Thank you very much for viewing my work.
Buen trabajo amigo. Pero esos rodamientos que has usado para el cabezal te acabarán dando problemas. Yo los usé y ahora tengo que cambiarlos porque cogieron holgura y no van bien.
@@AsencioAlex Hola Alex, yo también soy de España, y quería preguntarte qué tipo de rodamientos vas a poner en el cabezal. Y ya aprovecho y te pregunto si crees que las guías que ha utilizado en la cama para mover el carro, también podrían llegar a tener holguras.
@@antimiguel Hola Marcelino. Los que yo usé no te los aconsejo, acaban cogiendo holgura y te estropean las piezas y las cuchillas. Yo usé unos rodamientos que vienen con su cajetín, no se cómo se llaman, yo los conozco por quitacimbras. Ahora tengo que cambiarlos por unos cónicos.
@@antimiguel y en cuanto a las guías, no he tenido problema alguno, aunque quizás las reforzaría con un par de rodamientos lineales más, tanto para el movimiento transversal como el longitudinal
Fener mili olmamış,düz rulman olmaz,konik rulman olmalı,boydan gezme yapar,ayrıca sol yan katerle sağ yön torna ediyorsun,o katerin tersi kesmez,kasnak salgılı ayrıca,support mili hariç güzel olmuş,Fener milini güçlendirirseniz iş görür.
El torno está en venda ? Soy interesado comprartelo. Cuanto quieres para venderme lo ❓❓❓❓❓ Eres de Europa ❓❓❓❓ En serio habló, esperó una respuesta. Un saludo .
Only in the hands of a bad welder. Gasless mig is used by industry world wide for mig welding outdoors. That's what it was designrd for and gives perfectly good welds in the right hands.
Estoy haciendo engranajes de una motocicleta vieja para usar con un torno. Esperando verlo. Estoy intentando traducir de Google, si me equivoco, lo siento.
poor pully alignment combined with pillow block bearings equals shit accuracy, repeatability.. seems like a waste of time and materials, unless you plan on just machining parts with poor tolerances.
Из за того что он руками крутит, и нет авто подачи? Этому станку электронную гитару надо делать есть проекты на arduino и ставить шаговый двигатель на продольную подачу, тогда можно резать резьбы и много чего интересного.
What I like the most about all the videos about my own lathes is the idea. Each such lathe looks different :)
Thanks for watching I hope what I do will be useful to you.
Think she’s a little top heavy and that’s why there is a bit of a wobble. But best lathe build I’ve seen, so refreshing to see a large build that doesn’t need a lathe to make it. Must have taken you a long time.
Great work full stop, end of. Brilliant!
Liked and subscribed
I worked in machine shops for 40 years. I never used gloves when operating machinery with spinny parts! Drills, lathes, mills. I worked with a guy that lost half of his hand because of a glove.
If the pillow bearings go bad, how will you change them? Spindle welded at both ends.
Excelente aporte, muy ilustrativo ,deseo que no se desanime y siga contribuyendo.
Saludos.
He was very good friend, it takes a lot of work I imagine, whoever watches the video thinks it is easy, but in reality you get to do it, it gets complicated.
Se que es muy difícil. Soy militar jubilado y nunca trabajé, ni estudié en ésta área, pero me atrae. Seguí otro camino, comercio y administración pero no era lo mío. Me hice militar más por necesidad que por convicción. Me jubilé hace casi 10 años. En la milicia estudié y aprendí algo de Inglés. Estudié y fui profesor en el área de Inglés, pero como la universidad del Ejército en la que estudie, en sus inicio había sido centro de capacitación técnica en todo lo relacionado a herrería, siempre me daba mis escapadas por los talleres y deseaba aprender, pero estaba inscrito en el área de la Electrónica y Comunicaciones.
Me gusta algo enseñar, pero me gusta mucho más aprender. Tengo un cuarto repleto de libros de todo tipo.
Me fascina la carpinteria, algo de la construcción, electricidad y electrónica algo aprendí, y mi tendencia a la implementación de herramientas.
Estoy instalando un taller... aún es solo para uso de instrucción...personal...
When you weld thick plate like that especially a but weld leave a gap the width of the bare metal of the rod your using between the plates I was a welder for 30 odd years. Amazing work by the way I have wanted to do something similar for years.
Nice job very empress now I can start making mine didn’t show how to make the tower but maybe in another video thanks awesome
Seen a few af these “home made” builds but most of them gave lathes that only turned but had absolutely no precision. This looks great! Very very nice job, hope to see a lot more of your great work with mostly readily available materials. Thanks for sharing👍🏻
Good machine! You're doing fine! BUT! NEVER work with gloves on a lathe unless you want to lose your hand! Do not stop the chuck with your hands! All workers know these rules! Observe safety precautions!
Gloves or a drill !
So far your home made lathe machine is the best on YT, precise work, good and heavy built for last, but one thing I noticed about 3 pillow bearings, they are trapped at their location without the chances for replacement, you need to cut the shaft to take them out, over all you are good and your lathe is perfect example of homemade machines with basic available tools, I need to watch your video for more than couple of times to learn things of building one for my shop and my hobby related works, thank you for sharing your experiences.
Sorry for the late reply The problem you're worried about, I fixed it but I didn't do it on youtube, if you look carefully, you'll see the fix in my next clip. Thanks for watching
Oportunidad de
Лучший станок на Ю Тубе не этот . Лучшие станки у Debby Novrinal ., токарный и фрезерный !!!
ดูมาหลายคลิปหลายคนทำครับ ของพี่น่าจะหาอุปกรณ์ง่ายสุด เข้าใจง่ายด้วย ผมขอแบบได้ใหมครับ และขนาดอุปกรณ์ จะทำเองใว้ใช้ งานที่บ้านสักตัว ผมไม่มีความรู้เรื่องเครื่องกลเลย อยากมีใว้เรียนรู้ใว้ทำงาน Diy ที่บ้าน
แบบเครื่องผมไม่มีล่ะสิ แต่เรื่องที่จะทำใว้ใช้ที่บ้านผมแนะนำเลยมันใช้ดีมากไม่ต้องพึ่งร้านกลึงเลยถ้างานมันไม่ใหญ่มาก และอีกเรื่องคือผมจบช่างยนต์มาแตผมชอบงานกลึงผมจึงทำมันขึ้นมา
Excellent work
Ok , tôi thích cách làm của bạn , bạn đã làm rất tốt 👍
Es un hermoso trabajo, me encanta, pero tengo una duda con los tres soportes del husillo, ya que en muchas maquinas solo he visto solo uno en cada extremo.
You may want to see if you can get some housings made for taper roller bearings. Preloaded and well-lubricated, they should be significantly better than pillow block bearings.
عاش الايادي
شكرا لاهتمامك. في المستقبل، سأولي المزيد من الاهتمام للسلامة. لقد استخدمت برنامج ترجمة غير صحيح، أعتذر.
Нет необходимости в трёх подшипниках шпинделя ,
Good job.
I see only 2 mistakes.
1. You weld both sides and U cant change bearings without cut.
2. You use a metric thread not trapezoidal thread. Metric can stuck.
Except that is nice.
Sorry for late reply. I have fixed the shaft that is welded on both sides. and there is a project that will put the taper bearing but haven't had time to do it yet Thank you very much for viewing my work.
Buen trabajo amigo. Pero esos rodamientos que has usado para el cabezal te acabarán dando problemas. Yo los usé y ahora tengo que cambiarlos porque cogieron holgura y no van bien.
I had this problem as well. After a while, I will fix it better.
Perfecto. Saludos desde España.
@@AsencioAlex Hola Alex, yo también soy de España, y quería preguntarte qué tipo de rodamientos vas a poner en el cabezal.
Y ya aprovecho y te pregunto si crees que las guías que ha utilizado en la cama para mover el carro, también podrían llegar a tener holguras.
@@antimiguel Hola Marcelino. Los que yo usé no te los aconsejo, acaban cogiendo holgura y te estropean las piezas y las cuchillas. Yo usé unos rodamientos que vienen con su cajetín, no se cómo se llaman, yo los conozco por quitacimbras. Ahora tengo que cambiarlos por unos cónicos.
@@antimiguel y en cuanto a las guías, no he tenido problema alguno, aunque quizás las reforzaría con un par de rodamientos lineales más, tanto para el movimiento transversal como el longitudinal
I'd love to own a lathe
Then Go !! And BUY !! ONE !!
Hi Toyz the Lead Screws what size please? What motor you using? Very impressed!
I use a 1 HP water pump motor.
The Lead screw size with 2bolts for carriage? Thanks again
รบกวนสอบถามครับ เต้าจับดอกกลึงซื้อได้ที่ใหนครับและราคาเท่าไหร่ครับ(ชื่นชมครับ ดูตอนแรกนึกว่าคลิปต่างชาติแต่พอได้ยินเสียงเด็กเท่านั้นแหละครับดีใจว่าเป็นของคนไทย5555
ปากจับซื้อจาก lazada ครับราคาประมาณ 3000 กว่าๆตอนนั้นผมซื้อตอนมันลดราคาพอดีครับ
ขอบคุณมากๆนะครับผม
Круто идея не плохая.
А двигатель запитан через частотник??
ช่องนี้ดีมากครับ ถามอะไรตอบหมดไม่มีกั๊ก
ขอบคุณมากครับที่รับชม ฝากติดตามผลงานชิ้นต่อๆไปด้วยนะครับแต่ผลงานอาจมาช้าหน่อยนะครัับเพราะต้องติวลูกชายเข้าโรงเรียน
The blue motor you have mounted is that of an electric pump that I build :-)
Excellent job as usual! We featured this video on our homemade tools forum this week :)
Fener mili olmamış,düz rulman olmaz,konik rulman olmalı,boydan gezme yapar,ayrıca sol yan katerle sağ yön torna ediyorsun,o katerin tersi kesmez,kasnak salgılı ayrıca,support mili hariç güzel olmuş,Fener milini güçlendirirseniz iş görür.
Нет сквозного отверстия в шпинделе , а это ОЧЕНЬ ограничивает возможности станка , сэр ! Вы наверное уже сами в этом убедились ....
Nice work👍👍👍
buen trabajo, seria genial que compartieras tambien las medidas que usaste para hacer tu torno. gracias
Bagus , mudah , dan simple , 👍👍👍👍👍
Thanks for watching
This is amazing.. Thanks for share.. terima kasih
Memang jozz lur ✴Pareng
Can speak malay..... 😲
@@woody9246 i'm from Indonesia.. thanks
Deveria ter arvore tipo tubo de 4polegada para placa para trabalhar com furo ok sou torneiro ok
Great! !! By all means, I want to imitate it. Thank you UP
Ótimo trabalho amigo.
Thanks for watching
Brilliant!
nice work
good job
fajna maszyna 👌👍👍
Cała twoja praca jest doskonała. Śledzę twoją pracę. Przetłumaczyłem z google, przepraszam, jeśli to nie jest poprawne.
Amazing work. Is it possible to get the plans? And where you sourced things like the chuck?
Most of the materials I buy second hand products. The jaws of the lathe, I bought it from Lazada.
Exelente..
How much is that chack
ขอบคุณมากนะครับที่ให้ความรู้ ผมขอเรียก พี่ว่าอาจารย์ นะครับ ผมเป็นเด็กอายุ18 ที่ชอบในงานแบบนี้มากๆครับขอบคุณนะครับอาจารย์
ผมยินดีมากครับที่ชอบผลงานของผม และผมก็ดีใจมากที่เด็กรุ่นใหม่งานแนวนี้ อย่าลืมติดตามด้วยนะครับ
Ang ganda ng pagka gawa boss gagawa din ako niyan#angelbacaling
boss, mas mura ba gumawa nyan, kesa bumili ng gawa na? magkano kaya nagastos nya?
Esta soldador ambos lados , si tiene que cambiar un rodamiento tiene que cortar la soldadura!!
Muy bueno💪👏
Sieht gut aus das Teil. Aber ein Konstruktionsfehler ist doch dabei. Wenn beide Flansche angeschweißt sind, lassen sich die Lager nicht mehr tauschen.
Thanks for watching I have solved that problem. But I didn't make a video to watch. Because I did it temporarily before making a big correction.
Very good job... You speak Italian?
No, I speak Thai.
You didn't show it cutting it was already smooth
boss, how many watts do you use???
Toooooooop...
รางสไลซื้อได้จากไหนครับ
ซื้อมาจากร้านขายของเก่าแถวบ้านครับ
เอ้า พี่เป็นคนไทยหรอเนี่ย👍
ใช่ครับ
ทำแบบนี้ให้สักเครื่องได้มั้ยครับ
ไม่ได้รับทำเลยครับ
ครับผมชอบฝีมือพี่มากๆครับ
El torno está en venda ? Soy interesado comprartelo.
Cuanto quieres para venderme lo ❓❓❓❓❓
Eres de Europa ❓❓❓❓
En serio habló, esperó una respuesta. Un saludo .
I'm in Thailand And I don't know how to send it to you. Plus, are you really going to buy it? It's just a scrap of iron, it's not even completed yet.
What size chuck did you use
Jaw size 5 inches
Are u running a speed control on the motor or just one speed for now.
Which motor is use?
sorry for late reply I just saw your comment, I use a 1 hp water pump motor.
Are you from Thailand
คนไทยรึป่าวครับ
ใช่ครับ
What are the dimensions of the bed
dimensions of the bed = 21x90cm.
use dynamo how many HP?
1HP From the water pump motor
oh begitu ya.
thankyou MR always succes.
Interesting the project, but buy a good mig, this one without gas makes a horrible weld. And that kind of buzzhousing.
Only in the hands of a bad welder. Gasless mig is used by industry world wide for mig welding outdoors. That's what it was designrd for and gives perfectly good welds in the right hands.
หัวจับสั่งจากไหนครับ เท่าไหร่ครับ
สั่งจากlazadaครับ ราคาประมาณ3000กว่าๆตอนที่ซื้อเป็นช่วงที่ลดพอดีมันเป็นปากจับของจีนนะครับคุณภาพตามราคาพอรับได้อยู่
@@thetoyz9463 ครับ
Hallo what is your Φ or OD? on your spidle shaft? Nice try anyway!
It is 35mm as he has used P207 bearing housing visible at 17:28.
Muito bom 👍 forte abraço de nós do CANAL FERREIRA MOTOS
เพลาทะลุโตเท่าาไหร่ครับ
ผมใช้เพลาตัน ขนาด32มิลครับ รอโควิดเบาลงผมจะเปลี่ยนเป็นเพลาทะลุครับ ออกไปซี้อของมาทำไม่สะดวกครับ
@@thetoyz9463 เพลาทุลุ32มิลมีด้วยหรอครับ
ผมหาตลับลูกปืนขนาด32มิลไม่มีเรยครับ
ตอนนี้ผมกำลังจะทำเครื่องกลึงอยู่ครับ
หัวจับ5นิ้วยังคิดอยู่ว่าจะใช้เพลา
30 35 40 มิลดี
เพลา32มิลมีครับแต่จะหาลูกปืนยากหน่อยของผมใช้เป็นตลับเพลายืน ucp207ครับ แต่หากถ้ามีเพลาใหญ่กว่าที่ผมใช้จะดีมากมันจะไม่สั่น แนะนำนะครับควรใช้เป็นเตเปอร์แบริ่งจะดีมากมันจะเสถียรเวลากลึงครับ แต่ถ้าประหยัดงบทำแบบที่ผมทำมันก็ประหยัดดีครับกลึงงานออกมาพอรับได้ครับ
@@thetoyz9463 เอาเพลาสัก40มิลจะนิ้งขึ้นไหมครับ ตลับลูกปืนแบบสี่เหลียม
Mite be an ok hobbie lathe. small stuff would work ok.
Stability?
The overall machine is stable when working. But the spindle head deflects a bit and needs to be fixed first to be better.
@@thetoyz9463 I know I've seen the frame move when it works.
SON MUCHAS RPM!!!!
Estoy haciendo engranajes de una motocicleta vieja para usar con un torno. Esperando verlo. Estoy intentando traducir de Google, si me equivoco, lo siento.
คนไทยใช่ใหมครับ
ใช่ครับ
@@thetoyz9463 สุดยอครับ จริงๆถ้าคนไทยทำแบบคุณทุกคน ผมว่าเราเจริญกว่านี้ครัย
ผมแนะนำให้ทำเองหลายคนแล้ว
แต่ส่วนใหญ่บอกน่าอาย ไร้ศักศรี
สู้ซื้อของจากนอกดีกว่า
คนพวกนี้อยู่ตรงใหนก็ไม่มีวันดีขึ้นครับ
ไอัแค่แท่นกลึงยังทำไม่เป็น ทำเองไม่ได้ สุดท้ายเราก็มีแค่ตระกร้อมาราทอนกับรองเท้าเตะดาวเทียมเท่านั้น
ขอฃขึ้นแต่เช้าเลยครับ
ขออภัย ที่เขียนยาว
ท่านสุดยอดมากๆครับ นับถือ
@@thetoyz9463 สอบถามนิดครับ ยังไม่มีที่ยันศูนย์ด้านหลังแบบนี้สามารถกลึงเกลียว 1/2-20 ได้ใหมครับ
ยังไม่ได้ครับ เครื่องนี้ยังไม่สมบูรณ์เหลือตัวยันศูนย์
ใช่ครับ ซื้อมันง่าย สวยดูดีแต่เราซื้อความสำเร็จคนอื่นมาอวด หากเราทำเราจะเอาความภูมิใจของเรามาอวดคนอื่นและจะบอกกับลูกหลานเราได้ว่านี่พ่อทำเองนะลูก
Chamuyo, esa base no está plana para nada, desde ahí nada puede salir bien
jajajaja, cinta de papel, jajajaja, lo que hace youtube, jajajajaj
ประหยัดเงิน ใช้น้ำมันปรุงอาหารสำหรับสเปรย์กันกระเด็น
ผมก็ใช้อยู่เหมือนกันครับ ใช้ดีมากเลย
poor pully alignment combined with pillow block bearings equals shit accuracy, repeatability.. seems like a waste of time and materials, unless you plan on just machining parts with poor tolerances.
how was the first lathe produced?
@@paulslevinsky580 probably with more engineering insight than this. :)
This is my first device
@@thetoyz9463 Great job!!! I was asking jeolman how perfection was achieved with the first "round" turning machine.
@@jeolman1 you know what they say about art critics....
Kalu order harga berApa yah????
Sorry, I don't understand you asked. I tried to translate but I still didn't understand.
@@thetoyz9463 he's asking how much you sell it. If he really want to buy it, I guess
สอบถามหน่อยคับอุปกรพวกนึ้ซื้อที่ไหนคับใช้งบประมานเท่าไหร่คับแยสกทำบ้างคับ
ปากจับและชุดใบมีดผมซื้อจากlazada ส่วนของที่เหลือเช่นพวกรางสไลด์และเหล็กผมซื้อมือสองจากร้านรับซื้อของเก่า เรื่องงบประมาณผมหมดไป7000กว่าๆ มันแพงที่ปากจับกับชุดใบมีดครับ
А ни че что при продольной подаче резец прыгает?
Из за того что он руками крутит, и нет авто подачи? Этому станку электронную гитару надо делать есть проекты на arduino и ставить шаговый двигатель на продольную подачу, тогда можно резать резьбы и много чего интересного.
สั่งรางสไลด์จากไหนครับแบบแบนแบบนี้
มันชื่อว่าลิเนี่ยสไลด์ครับของใหม่มีขายในลาซาด้า ของที่ผมใช้เป็นมือสองครับ
@@thetoyz9463 อ๋อครับผมเคยเห็นแต่แบบกลมๆ
Bisa pesen
What do you order?
เครื่องกลึงตัวนี้ลงทุนเท่าไหร่ครับพี่
ลงทุนไป7000กว่าบาทครับ ค่าเหล็กไม่เท่าไหร่ หมดเปลืองตรงปากจับ และตัวชุดจับใบมีด เพราะของส่วนใหญ่เป็นของมือสองที่หาซื้อจากคลองถม กับร้านขายของเก่าแถวบ้านครับ
สุดยอดครับพี่ จะเป็นกำลังใจให้และจะติดตามผลงานนะครับพี่ ขอบคุณสำหรับการสร้างงานโดยฝีมือคนไทย ขอบคุณครับ
It certainly vibrated a lot with this type of bearing.
Станина хилая
Spindle bearing total garbage! Threaded rod as a drive even worse! what junk!