Es el vídeo mas didáctico que he visto, No entiendo porqué tantos dislike (mas parece E N V I D I A). De mi parte lo felicito por tan excelente trabajo y le doy mil gracias por Compartir la Experiencia. Saludos y que el Bien le acompañe.
@@zana3587 معذرةً سيدي ماهو نوع لف الارميچر اقصد ماهو اسم الطريقة او الاسلوب الذي تم اللف فيه هذا اولاً وثانياً هل هذه النسبة ١٠٪ ثابتة عند التحويل من الالمنيوم الى النحاس ام تتغير مع تغير نوع المحرك او حجم السلك. مع الشكر
Explanatory video I've ever Watched, but disassembling armature from gear housing is a hard job and it was missing in the video-May God bless you and increase your knowledge
Good one but commutator connection not clear.looks like Each winding end point connec to one commutator segment behind the starting commutator segment. I am I right. If it is clear this is best video I have seen in the u tube
You could probably use regular parchment paper as it is used for high temperature baking. I have used regular paper when winding my RC motors and it works well.
عاشت الايادي وكثر الله من أمثالكم استاذنا العزيز وافضل فيديو تعليمي شفته بالانترنت الى الآن فقط أسأل اضافتكم المادة السائلة الى وعاء قدح الماء لعمل العزل على المخدة ممكن نعرف المادتين شنو هل ورنيش وضفت عليه مادة مسرعة للتجفيف أم ماذا وشكرا جزيلا
the wire comes already coated its called magnet wire do you use a resin like same for fiberglassing polyester resin or a epoxy im guessing will be safer on different wire insulations
Great video and amazing job. Well done. Could you please tell me what is resistance of rotor and stator after repairing? Mine is working but is giving strong sparks on brushes. Unfortunately can't find short, open circuit or anything else what could cause this. Visually also everything looks fine. Waiting for your answer and help.
explained why they are cheap: winding in aluminum, much cheaper than copper but with a much lower melting point (600 ° C versus 1085 ° C) just put it under stress for a little more than expected and goodbye good old friend!
Dobra robota widać że jesteś fachowcem sam film również dobrze się ogląda jedyne czego mi brakuje to pomiarów uzwojeń po przezwojeniu by pokazać jak było a jak jest oraz informacji jakiej chemii używasz
nice video , Thanks , I have a problem with my cutter just yesterday change the ball bearings and Foley Butterfly locked the cutter i solved the problem , but now when the cutter working , it seems to me that the i have speed changes , i feel it with the sound , what can you suggest to me ?
I'm in doubt, too. I remember that a mass "m" not balanced, out of center of a distance "r" from the axis, will produce a centrifugal force m•r•( angolar speed )^2 ( if i'm not wrong ... ) More the angular speed, much more the centrifugal, but - as in my formula - "m" and "r" are not depending from speed, so a static test and correction would be enaught ? I remember instead ( many many years ago ) - when i was servicing some equipments where the motor sometime become burnt - after rewinding they use to speed up the rotor ( just posed on free runnig pillows ) with a bare rubber wheel from a motor of the equipment, and with the use of a sincronized flashing light, they were able to understand where a mass was unbalanced, and so correcting this error scratching a bit of iron ... Somebody can explain the trick ?
great video, but some audio would make it perfect to understand the why and how to repair, for beginer like me to learn . thank you and like i said great video keep them coming . friend from canada
Inglês Very good work ... Excellent work very well. Can you tell me the reference of the varnish that uses only stator? And what is the reference of the varnish you use on the rotor? What is the card to separate the reels ... I am very sorry for my English ... I am Portuguese ... Thanks for your great work videos ..
thank you sir , the varnish is i used it is bad quality because there is no good quality in my country. the third question, the card i buy it in my market 1 meter about 2$ in my country
First,,, many thank to the excuter of this good video,,, Please I want help from person rewinded such armature because I rewinded the same armature by follow the same steps in the video but the result was negative ( high spark) what I will do after,,, I want diagnosting,,,,,, thank you,,,
Please come and see instructions to fix the television.
🙏Thank you so much for watching my video, please don't forget to LIKE & SUBSCRIBE. ✌
Es el vídeo mas didáctico que he visto, No entiendo porqué tantos dislike (mas parece E N V I D I A). De mi parte lo felicito por tan excelente trabajo y le doy mil gracias por Compartir la Experiencia. Saludos y que el Bien le acompañe.
تبارك الله عليك . صنعة وحرفة
متقنة . امثالك من يجعل الانترنيت ممتع ومفيد للغاية
شكرا كثيرا
اشكرك اخى العزيز
كالعادة عمل رائع و متقن وشرح واضح. مزيدا من عمليات إنقاذ الادوات التالفة و إعادتها الى الحياة.
اشكركر اخى العزيز
Unbelievably good job. Congratulations.
У мастеров руки все черные. Пропитанные маслом. А у вас чистые и ухоженные.значит вы ещё ученик.😊
благодарю вас
افضل فيديو شاهدته خلال هذه الفترة عمل اكثر من رائع انت تستحق عشرة على عشرة
اشكرك سيدى
@@zana3587 معذرةً سيدي ماهو نوع لف الارميچر اقصد ماهو اسم الطريقة او الاسلوب الذي تم اللف فيه هذا اولاً وثانياً هل هذه النسبة ١٠٪ ثابتة عند التحويل من الالمنيوم الى النحاس ام تتغير مع تغير نوع المحرك او حجم السلك. مع الشكر
Tebrik ederim çok detaylı ve açık bir video yapmışsınız, teşekkür ederim.❤
Thanks for rewinding universal motor. Good video.
Sei un genio ! vorrei averti come vicino di casa.
Explanatory video I've ever Watched, but disassembling armature from gear housing is a hard job and it was missing in the video-May God bless you and increase your knowledge
yes, thank you sir
Muito bom mesmo serviço no capricho parabéns
Muitobommesmoservionnocaricho
Huhujgjfut ytyg
Fycy
Good one but commutator connection not clear.looks like Each winding end point connec to one commutator segment behind the starting commutator segment. I am I right. If it is clear this is best video I have seen in the u tube
Super 👍 robota kolego 😊 dziękuję.
Pozdrawiam serdecznie z Polski.
best video on armature rewinding on the internet
thank you sir that is very kind of you
@@zana3587 qqq
Parkside and aluminium wire on the stator of the angle grinder. Thanks for pointing this out.
thanks for such a detailed video on winding armatures. maybe after i have watched a thousand more times i will try it myself
thank you sir i hope it's useful for you
I always wanted to learn how to rewind a motor. Thankyou
Thank you sir
yes of course, a new one cost 30$ for what to do this anymore in our days?
Me too
@@zana3587 a 4
Gewußt wie, ja gelernt,ist gelernt.Klasse.
Danke mein Herr
Génial superbe magnifique boulot
You are an artist!
thank you sir
Muy Buen Video.
*¡¡¡ BUEN TRABAJO !!!*
gracias Señor
that was perfect.I'm from Iran🌴🌴🌴
thank you sir
Good video. Better than most on the subject.
thank you sir
Good job from brilliant professional man
عمل رائع من إنسان محترف ممتاز
شكرا اخى
Un grande cervellone. Vai cosi'
Que buen video 😊😊😀😀 saludos desde Cochabamba Bolivia 🙂🙂🙂👏👍👏
gracias Señor
about how long of wire would you guess that was
23 ga rotor
ive got a router rotor to do its about the same size
thanks and great video
thank you sir
Teşekkürler ustam super oldu bizide aydinlattınız.Sağolun. (Dhang)
Perfect video. Thanks from Slovakia. What is the white insulation (paper)? Can't find it on ali.
thank you sir i buy the paper in the market
You could probably use regular parchment paper as it is used for high temperature baking. I have used regular paper when winding my RC motors and it works well.
Thanks for demonstrating armature and field coil winding. Best regards
بسیار مفید واموزنده بود موفق باشید
ممنونم برادر
The best repairman , thank you sir 👍
thank you sir that is very kind of you
This was awesome! My grandfather did rewind some transformers. I never though it is possible to rewind a rotor.
thank you sir i hope it's helpful for you
Would it be cheaper Toby one?
عاشت الايادي وكثر الله من أمثالكم استاذنا العزيز وافضل فيديو تعليمي شفته بالانترنت الى الآن فقط أسأل
اضافتكم المادة السائلة الى وعاء قدح الماء لعمل العزل على المخدة ممكن نعرف المادتين شنو هل ورنيش وضفت عليه مادة مسرعة للتجفيف أم ماذا وشكرا جزيلا
اشكرك اخى العزيز . وارنيش + تنر
كيف ضربت قياس قطر السلك وطلع الناتج 21.5
أنا حزين لأنّي ماعرفت قناتك من قبل :(
مشترك ١٠٠٪ . و الله مبدع ماشاء الله عليك. شغل نظيف و مرتّب و محترف.
اشكرك اخى العزيز
Hello How does the 3 drill system rotate?
Please advise.
زۆر جوانە مامۆستا لەشت ساغ بێت
bareze
This is excellent sir
Thank you sir
Vc não faz balanceamento no induzido? gostei muito do vídeo
thank you sir . look at time bar 17:38
U just made better tool than factory did! Great job bro!
Please I Am rewinded the same armature by follow the same steps but the result was not sucssed,,, high spark,,, I dont know why???
Отличная работа!! Терпение и внимательность!!
спасибо, сэр, это очень мило с вашей стороны
@@zana3587 Хорошую работу видно сразу!
Very very good عالی عالی عالی عالی بودی
thank you sir
Estator e induzido nota 10 pinhão e coroa nota 3
What type of insulation do you use to cover the copper wires? and how do you prepare, thanks for your video it helps a lot greetings from Mexico
i use resin
@@zana3587 Why did you use 2 different types of resin? Can you provide a link to the resin?
the wire comes already coated
its called magnet wire
do you use a resin like same for fiberglassing polyester resin or
a epoxy im guessing will be safer on different wire insulations
Why did you choose an higher gauge for copper wire? Copper has a lower resistance than aluminum, so the copper wire should be smaller than aluminum.
Ful chamba excelente obra maestra desde peru
Very cool video, nicely demonstrated. By the way, what do you think about parkside tools?
thank you sir , not a good quality
Better than the original 👍
thank you sir
From Indonesia : Exelent video thanks brother
thank you sir
Блин классно ,когда умеешь, 👍👍👍 вот только я не понял 🤔🤔🤔откуда и куда что надо крутить ,куда закручивать и как куда соединять 🤷🤷🤷
hhh ok
Great video and amazing job.
Well done.
Could you please tell me what is resistance of rotor and stator after repairing?
Mine is working but is giving strong sparks on brushes. Unfortunately can't find short, open circuit or anything else what could cause this.
Visually also everything looks fine.
Waiting for your answer and help.
It could be the weight, maybe it's not balanced or maybe you have connected to the wrong bar on the comentator or the bars are shorting
Μπράβο πού καλή δουλειά και εξαιρετικός δάσκαλος.
σας ευχαριστώ, κύριε
good job
👍👍👍👍😍
explained why they are cheap: winding in aluminum, much cheaper than copper but with a much lower melting point (600 ° C versus 1085 ° C) just put it under stress for a little more than expected and goodbye good old friend!
yes they used aluminum because it's cheap
Dobra robota widać że jesteś fachowcem sam film również dobrze się ogląda jedyne czego mi brakuje to pomiarów uzwojeń po przezwojeniu by pokazać jak było a jak jest oraz informacji jakiej chemii używasz
dziękuję panu, mam nadzieję, że to pomoże
👍👍👍👍👍👍👍👍👍
thank you sir
Excellent work very good
Thanks
Thank you sir
nice video , Thanks , I have a problem with my cutter just yesterday change the ball bearings and Foley Butterfly locked the cutter i solved the problem , but now when the cutter working , it seems to me that the i have speed changes , i feel it with the sound , what can you suggest to me ?
my cutter just have one speed without dimer
хорошая работа)),а можно инструмент с 220 на 12 или 24 в перемотать? я переделывал сетевую УШМ от китайского 775 двигателя но он быстро сгорел
I jak zwykle profesjonalizm 😉
Pozdrawiam
dziękuję panu, bardzo miło z twojej strony
Beautiful!
it was satisfiying when he took the old winding of the coil out
yes sir
Best tutorial ,, thank you 😘
thank you sir
عاشت الأيادي أستاذي المبدع المادة الصفراء الذي وضعتها علا الملف أيبوكسي ام وارنيش
اشكرك اخى العزيز . وارنيش
You start winding from the the end of the last coil you have marked . Sould you step back two segment.
You are a lifesaver
yes sir
Frome Algérie good job 👍🏿
Thank you sir
Який лак ви використовуєте?
Great job, but what about balancing. After all, the rotor is spinning at a speed of about 24 thousand. rpm?
I'm in doubt, too.
I remember that a mass "m" not balanced, out of center of a distance "r" from the axis, will produce a centrifugal force m•r•( angolar speed )^2 ( if i'm not wrong ... )
More the angular speed, much more the centrifugal, but - as in my formula - "m" and "r" are not depending from speed, so a static test and correction would be enaught ?
I remember instead ( many many years ago ) - when i was servicing some equipments where the motor sometime become burnt - after rewinding they use to speed up the rotor ( just posed on free runnig pillows ) with a bare rubber wheel from a motor of the equipment, and with the use of a sincronized flashing light, they were able to understand where a mass was unbalanced, and so correcting this error scratching a bit of iron ...
Somebody can explain the trick ?
Cauge 23 is 0,55 mm thickness, right
What product did you use as an insulating liquid?
resin epoxy
I have a DC motor that has been burned after connecting it to 220v instead of 110v.
Can i fix it the same way or it's different since it's DC?
great video, but some audio would make it perfect to understand the why and how to repair, for beginer like me to learn . thank you and like i said great video keep them coming . friend from canada
thank you sir
Nice video but i would know the insulation product you are using
Is varnish or something else
Thank you.
thank you sir
Как технопорно- великолепно. А так- делать такой ремонт пятидесятиеврового артикля мог только коммунист!
Спасибо, сэр
Felicitari!
Pentru impregnare folosești lac sau rășină epoxidica, te rog sa mi spui ce tip? Mulțumesc!
what did you factor in when changing from 20 gauge to 21.5? Is it the resistivity? Why did you apply 10% more rounds in case of copper?
There is a table on the internet that you can check
@@zana3587 اين هذا الموقع من فضلك
@@zana3587 فعلا التحويل يكون بزياده نصف دوزيم كما هو معروف للجميع لكن ....انت قد يكون لك راي اخر
@@zana3587 أرجو منك الرد
هناك شخص فى اليوتوب اسمه اعتقد خالد المعمورى لديه جدول تحويل الالمنيوم الى نحاس فى احد فيدوهاته . لا اعرف اسم الفيدو . و ب العربي
Nice vedio bro thanks more blessings to you GOD BLESS
thank you sir
Please explain us and teach us rewinding sir thanks
Big fan
How to find start pin? Confusing for me.
Hi! Nice winding! I ask only ask where you connect the start wire winding and the last wire winding? To carbon?and to live wire.thanks
can you show me in time bar
Inglês
Very good work ... Excellent work very well. Can you tell me the reference of the varnish that uses only stator? And what is the reference of the varnish you use on the rotor? What is the card to separate the reels ... I am very sorry for my English ... I am Portuguese ... Thanks for your great work videos ..
thank you sir , the varnish is i used it is bad quality because there is no good quality in my country. the third question, the card i buy it in my market 1 meter about 2$ in my country
hello, what kind of spacers did you use between the windings, the white ones?
Che prodotto hai usato come liquido isolante? Tank
resin epoxy
Very interesting 👍
Thank you sir
Am only behind on how you are testing with the light bulb please kindly explain the purpose of it. Thanks
you can check video 17 in my channel
how to give more like to this video!!! Incredible!
thank you sir
Bom trabalho, god Job!
Brasil.
thank you sir
Amazing
Good job
From tunisia
Thank you sir
@@zana3587 h
نایابە هەربژیت
بةريزى
Perfect video from SERBIA
thank you sir
First,,, many thank to the excuter of this good video,,, Please I want help from person rewinded such armature because I rewinded the same armature by follow the same steps in the video but the result was negative ( high spark) what I will do after,,, I want diagnosting,,,,,, thank you,,,
Супер!!! Яка ціна ремонту??? Дякую за відео 👍👍👍✌️✌️✌️🇺🇦😷
це коштувало близько 5 $
@@zana3587 В якому місці ви мешкаєте???
Wow looks so easy. God job
thank you sir
Excellent work 👍🇵🇪
Thank you sir
நன்றி நன்றாக இருக்கிறது
நன்றி ஐயா
Awesom.but sir.what whould u do if there are sparkiling in both side..i have that problem..
thank you sir, sparkling in both side! that is meaning you make a mistake when you winding it
First like . Great work my brother.
thank you my teacher, you the king of winding
@@zana3587 your welcome my brother. You the king too.
Thank you brother