Samsung Gear S3 Watch Dead Repair
Вставка
- Опубліковано 31 гру 2024
- Samsung Gear S3 Watch Dead Repair,
NOTE: IF THE BATTERY IS LITHIUM POLYMER 3.7 VOLTS, SO PLEASE DON'T CHARGE IT WITH A 5V POWER SUPPLY. CHARGE IT WITH A 3.7 V POWER SUPPLY.
Download Samsung Gear S3 and S2 Repair FIRMWARES
GUIDE TO CONNECTING A SAMSUNG GEAR S2 AND S3 DEVICE USING WI-FI AND USB
electrovo.com/...
Download PDF file:
electrovo.com/...
Paypal link:
www.paypal.me/...
#
UA-cam Channel:
www.youtube.co...
Visit our Blog:
electrovo.com
/ anwarigroup
Twitter:
/ abdul_habib_7
Facebook page:
/ electrovofunpage
I have got to admit that I was watching this thinking "There is no way this will work." But I bit the bullet cause I was pretty much at the end of the road with me favorite watch and tried it. I was SHOCKED when the screen came to life for the first time in a week. I have it charging now.
I am curious though, once the watch gets to 50% or even 100% charged, will I have to do this EVERY TIME I want to charge my watch? Or will the cradle charger work again?
Hi, you don't have to do that every time, but try to change the battery to a new battery if it happens again.
@@anwarigroup Thank you so much for the advice and help!
Basically manually jumpstaring battery to a percent that will be recognized by motherboard and allow charger to charge and balance the battery.
Dropped a like and also subscribed because you are a good person. I read all the comments on the video and you took the time to respond to everyone and help them fix their watches. Big thumbs up to you sir!
Also Good job soldering those little ass connections so quick!
God damn it, you saved my watch. This is literally the only video on youtube that explains this trick. Cheers mate, great job! I also held the wires with my bare hand for a couple of seconds till the screen shown that it's charging, then I've fully charged it using the watch's charger.
This channel is amazing, Habib. Please keep up uploading great videos like this. All the best from Spain 😉
Thanks for comment, I will be uploading. Cheers
If the red light on the dock is flashing your battery is full discharged then: Put the watch on the dock red light is turn on when starting flashing take the watch out of the dock then put it again when start flashing take the watch out and do the same about 10 times and the watch will start charging. Cheers
It didn't work for me.
Thank you very much, you saved my day !
Sorry friend can it possible solder only red and black cable of the usb to charger the battery? Why also data (green & white)? Thanks
For charging, RED for positive and Black for negative will be enough. Green and white are for data communication.
I know it! In your video you solder all cable also data but for relife the battery drained it's possible solder only red and black cable and connect it to supply power 2A 5V usb or other amper (1A)? Thanks
@@lillyminutolo5716 4-5V. One hundred mA to 2A would be fine.
got my watch to charge with this method. so now i just cant let the thing run out of battery? or else i have to redo this mod?
Hello and thanks for the valuable content! I would like to ask, my s3 is not turning on, but when charging, the screen responds, showing the percentage of battery juice. Does this have to do with replacing the motherboard then?
Incredible. Y did it with a cable only with red and black and only charged it for 1 minute without solding them and with my hand steady jaja. Then I placed it in the charger and did a reboot pressing 3 times the lower button. And there it is.. charging from 1 percent...thank you man! 😂
You are the legend!.
@@anwarigroup had to do it again today and it worked. ..jaja.. thanks again
Great video. I did not know you could charge a battery like that. I´ve got a Gear S3 that charges no problem, but won´t turn on. Suspect the buttons are not working. Have you got a video that shows how to test them and carry out a repair, please?
Same problem, mine charges, it does not turn on
Outstanding! It worked! Thank you, Sir!
and thank you very much for this video you save my watch.
You are welcome
good day sir, may i know if soldering a usb cable to the board can stil be achievd if the green data pin is lost or removed from the board. please help me
There has to be a connection. If the pin is removed so solder it to the pad, If the pad is removed you have to track the pad to find its root and solder the wire. Without soldering wire, you can not connect it to the computer.
I've just opened up my Galaxy Gear Sport, and the terminals are slightly different. Do you know what colours I have to connect to which terminals for this model? Thanks.
Send me photo of your watch inside back cover and motherboard
@@anwarigroup Thanks for getting back to me. How do I send the image to you?
@@danielrobinson80 visit links on description. Go to website.use contact form
Can you upload this images please sir
the music is anoying but the trutorial is great!!!
Thanks for your opinion. This will help a lot. I will not be using a music track in future.
Don't listen to this guy, he can't even spell. The music is fine!
Which key did you use to open it?
By the key, if you mean screwdriver so I used Tri-Point 0.6 Screwdriver
Hi I have a dead S3 I wanted to know if you need to connect all the cables or just connect the red and black.
Thank you
red and black is for power. two other wires are from data transfer.
@@anwarigroup ok but for charging is necessary to connect the black and the white ok?
@@mikitoni13 Black is Ground (-)(Negative) power, Red is positive (+) power, white and green are for data transfer. If you you want to do data transfer such firmware update so connect all 4 wire. If you want to just charge up your watch so connect two wires, that are Red and Black.
@@anwarigroup ok i connected the black and white but the charge doesn't start .... can the motherboard be dead?
@@mikitoni13 connect black and red. If you connect the white so white has to be connected to a positive 3-5v power supply.
Is mine completely dead? Cannot charge. I drained the battery and did not charge for almost 5 days then this happens. I usually do this but this time it's completely dead.
Some batteries when they get fully discharged and are not charged for some time, can not be charged, so sometimes applying a few higher voltages directly to the battery, fix this problem.
thank you so much this help me and my watch was run again
I accidentally detached one of the terminals when soldering. Can I just completely remove it, then make the solder in place?
yes, but the base should be fine. If it is ground, you can take ground from metal plates.
@@anwarigroup Thank you for your quick reply. The solder is not sticking to the base, and I think it's messed up.
My understanding of the steps = 99%
Soldering skill = 0% haha
@@lalocampo what pin is damaged?
@@anwarigroup The white and green data terminals
@@lalocampo see if you can make a connection. use a multimeter
On my s3 sensor not working. Do you have any idea how to fix it
Hi, Open your watch, disconnect wall connections, clean them and put them back together, update your watch to latest firmware.
Your watch problem can be one of these issues:
Hardware, if it is hardware motherboard and or sensor, so you need to change one of them.
Second can be software, update or reset to factory settings.
What if watch is charging curectly but doesn't turn on? they doesn't react on button pressing at all
use a tweezer and short the button sides, maybe button is damaged.
@@anwarigroup thanks for the answer, i think that button is not the problem, owner of watch gave it to some guy and he either tried to update or replace its firmware, the thing nobody asked to do. Now i try to bring them back to life. After that dude the watch started to discharge very fast and turned off after full discharge. I've charged them full but they don't turn on. Maybe you have any ideas? Thanks.
@@aequitasveritas3419 recharge the battery, try again pressing home button, change the battery and try again, and or connect it to a power supply and try it.
@@anwarigroup I'll try to do so, thanks for the answer
@@anwarigroup found the reason, it is the button, oxidized contacts on the cable at the junction with the board, soldered it and problem solved
Turn off the music!! Can't hear your instructions.
Sorry Mike, this video can't be edited. Can you tell me what are you after so I can share you a good video?
Hvala
The battery in my Gear S3 is charged, but I can not turn on because the home button is not working. Can you tell if there's another way to turn the power on? Thank you!
Hi yes, you need to open it and short the home button connection and or replace the home button/power button.
@@anwarigroup Thank you! I`ll try It.
@@anwarigroup Hey, i'm facing the exact same issue, how can i short the power button and turn on the watch from the motherboard please ?
@@amine.n1319 Hi, open the watch. And you will see the contact buttons. Just short from outside. short for 5 to 10 seconds.
@@anwarigroup You mean the 4 pins ? But how can i short them ?
Have the same problem but charger lights up red but watch doesn't turn on, do I need a new battery?
You might need a new battery. Open it check battery connection.
Hi! Great video.
My gear s3 all of a sudden got a vertical line in the middle of the screen, very bright. It blinks a little and the screen turns off but the touch works well.
I recently changed its battery and it continued working well for two days. Then the problem showed up :( do you have any suggestions?
Thank you
Hi, The new battery can be faulty as well. First thing to do is to flash the watch with firmware. After that if its the same so try to change the battery again.
My power button is not working. any solution for that? Appreciate you.
You need to change it. For quick action, you can use a tweezer and short the two pins. You can search on eBay for a replacement button.
Hi, I have problem with my gear.
I use my samsung gear to swim and the water enter to the gear, and reboot system occur.
to solve the problem i came to samsung store to clear and dry all the water in my watch.
but today lifetime my gear its only 8 hours.
What should I do?
Change the battery?
Hi, change the battery. if didn't work change the watch.
If this does make the watch charge then what is the fix for the watch to go back to charging the normal way?
The problem of this watch was that the battery was fully drained. So in this case particularly for this watch, it was not able to be charged by the wireless charger., So The problem could be simple to boost the battery charge by connecting these wires. And or the problem can be with the battery. So the watch may need a new battery. Some times, the problem is in electronics, on the motherboard. So if it down to battery change the battery and it will charge normally. And if it just needs a boost charging as I did in the video so do it that way. Then monitor the battery and see how it goes. if the charge and discharge time is ok. So leave it like that, otherwise, change the battery.
@@anwarigroup thanks for your reply. I tried this fix and I think I might have messed up more as the soldering was not very good and there was a short circuit so it's not charging at all. I'll just have to throw it away.
@@Fylosofy_ if you want post it to me, I will try to repair it for you.
@@anwarigroup Where are you located? Because I'm in South Africa so the postage alone might cost more than what the fix is worth.
@@Fylosofy_ Yes, I live in UK. It is quite far.
Hey bro if i connect only 2 wires red and black will it charge?
Yes, it will, unless the red and black are not red and black. But does it matter? Yes, It does, as the Red needs to be positive input and black negative. Unless the colour is not important, but the polarity needs to be correct.
@@anwarigroup but if battery overheats by 2 % of power its dead better replace it right?
@@Izzy-w2p make sure not to connect 5v to the batteries. These batteries are about 3.7V. They are Lithium lipo batteries. However, if the battery is overheating, it can be due to many reasons, one of the reason can be the battery itself.
Hello Bro, I have messed up with my watch using ODIN, now it's in error mode and always display on mode. Can u help me?
You seem knowledgeable but I can't see what your doing good sir
This watch has power problem. The cell is fully drained off. The cell is gone over discharged limit and it can not be charged back. Or the cell could be faulty. So when a fine cell goes over discharge limit then it can not be charged back with the low current of the watch circuit board. Connecting 3 - 5 volts with 1 amp current directly to cell will boost the charge on the cell. So if the cell is faulty or electronics are faulty the cell will be drained off back again. If the cell and protection electronics work fine then the cell will stay charged about the discharge limit.
it takes a 6 hours to full charge and drain in 6 hours. can you help me what i can do???
Change the battery and check again.
Also, try with different charger if the result was the same.
Hi,
Sensors on my watch are not working after last update. Any idea what to do? Service centre wont touch my device.
Hi, See if you can restore the old software. Or download one old model and install that and see whats happening. Report this issue to Samsung. Wait for the next update. When next update came, update your watch and see if its working or not. If not so go back to old version. Report the issue to samsung. Wait for the next update. After update came, update your watch. Check the sensor. If its working so its fine if not send a report to Samsung. Use old software again and wait for the update. Repeat this loop until it start working.
Hello I have a samsung gear sport sm-r600
which does not start anymore.
When I put it on the charger it lights up with the logo (samsung gear sport) and turns off. the charging light is blinking but I can't turn it on.
I have changed the battery.
I can send you pictures and videos of the problem.
I went to your site but I cannot send you a message, (fire blocking)
Thank you for telling me how to do it
Thank you, I hope you can help me.
Send me an email Habib@electrovo.com
Have you solved?
Can i send my S3 frontliner for repair ?
I have same issue in my watch completely dead how to better soulation
hi dear need help for my bricked gear SM-R765 A ...cant connect using wireless connection ..for new firmware. and i dont have the software for my model .
please help
regards and thanks
anwar
Hi, Check this link
electrovo.co.uk/guide-to-connecting-a-samsung-gear-s2-and-s3-device-using-wi-fi/
@@anwarigroupthanks so much for the prompt reply ! great... i hope it will be safe if i give it a trial by myself..
regards
can you please give me your email ...i am not able to buy the firmware for (gear s3-sm-r 765 )
Hi sir..i charge to docking but red indicator at docking blinking..i use tester test the battery 3.6v..but my gear not turn on..whats problem..please..
check the side buttons with a multimeter, make sure they work.
i should let it for some time charging or instantly will turn on
Leave it to charge for 5-15 minutes, and press the power button
nice bro...
Thanks
Electrovo Electronics Fun Blog bro, i got question.. , screwdriver Y what size to open??
Hi its 0.6 Tri Point Screwdriver
I've had my Samsung Gear S3 watch for over three years. during the beginning of the 2nd year the watch won't turn on it showed 100% charged. but no matter what I did it won't turn on. I finally gave up trying an took the watch to the T-Mobile store I purchased it from. They performed a song and dance routine and then suggested I take it to a watch repair shop. I decided I wasn't ever going to get a Samsung watch again. Now tonight I'm on UA-cam an happen to run across a Gear S3 topic and it suggested placing the watch on the charger an perform the reboot routine. I was both happy that it worked and dismayed that the T-Mobile support didn't know about this.
My gear s3, flickering green screen and lines. How can i fix it? I tried rebooting it by holding the power button. :(
Put it in download wireless mode and flash the firmware.
I want to flash gear s3 frontier with usb cable like ur video of ( un brick gear s2) because i downloaded wrong frimware so the watch doesn't want to open so can i connect usb cable to pc and watch like the method in this video
Hi yes you can. More information are available in below link:
electrovo.co.uk/guide-to-connecting-a-samsung-gear-s2-and-s3-device-using-wi-fi/
I have changed my battery and now it wont start. When i charge it went from red to green. Anyone can help me?
Check your battery voltage by a multimeter and see how much charge you have there. if you have 3v so close your watch and charge it and try to turn on.
If your battery has no enough charge so charge it.
Check your battery after charging. See how much voltage you get.
Your new battery sometimes can be faulty too.
After that if battery is ok, so check your power switch. Your power switch can be faulty too.
If your battery is charging. and your power on switch and flex wire is ok. So then check all wires connected properly.
If everything is ok so then it works to the watch motherboard. If watch motherboard.
Your display screen can be faulty too.
Sow now if you have a spare motherboard and display screen, so check by replacing them.
Mi reloj carga pero no enciende
Comprueba tu botón de encendido. El botón de encendido puede estar defectuoso.
@@anwarigroup lo intentaré mañana y te aviso, crees que sea la pantalla solo le entro una gotica de sudor
My watch battery 4 volt but not charge or anything
No waterdamage. Sticker is white. I think other problem
Under the back cover of your watch is an electricity power receiver., Check that and check its a connection to the motherboard. That wireless power receiver has to transfer power to the board.
Hi friend, I'm trying to fix my watch by following one of your videos and what you posted on your blog, but this happens when I try to charge it with the wireless charger and when I connect it via USB ua-cam.com/users/shortsa-BJx6vO5a4