Thanks for the vid!!!! Very helpful replacing both left arms! Might want to mention that you need to put the front shoulder joint (?) in the half way position when reinstalling to preload it. Also I found if you pry up slightly on the ears (?) at the rear of the top shell, it comes off MUCH more easily.
hi mate, can you please run me through this half way position? like does the armm need to be in the open position? also what are you using to turn the joint. ive been stuck for a long time now. thanks
@@SuperAirman24 The rotation shaft is the little silver "can" with black plastic tee on the top (looks like a servo arm) You can see him pushing it out at (3:34) and the other arm's joint is on the table near his middle finger knuckle. Its the pivot and connection point for the front arms. Hold the "can" gently with a pair of pliers and with another pair to hold the arm. Rotate it gently and you'll feel it lock into position every 180 degrees. By "halfway" I mean the point between locking positions. It'll hold itself there if you're careful. Then install it on the drone with the arm partially open (it only fits one way) and push it down onto the tits where the black arm seats. Clear as mud huh? I've got one coming in tomorrow and I'll post a vid. If pictures are worth a thousand words and a vid is at least 10k. cheers
Hi can you make a similar video on putting back all the disassembled parts and getting the drone in working mode ( And can you pay special attention on soldering of the wires on mother board ) ?? Thank you
Nice video thanks! I have been doing some comparisons between US and EU model to find out the ADS-B hardware. I cannot find anything different between the two models. As per DJI, US models come with ADSB rf circuit and additional antenna and a different ESC powerboard
Hello, very good video, I have a big doubt, I want to know if you know where exactly the compass is located in the Mavic Air 2, I had a similar doubt with the compass of the Mavic Air v1 and after investigating more than 6 I was able to confirm that it was located in the main board, that is, it is integrated with the board. Do you know if the same thing happens with the Mavic Air 2 version? Thank you
Hello, is it possible to install an HDMI output in the Mavic Air 2 drone so that you can stream directly from the camera to the TV or PC? Thanks in advance
Question about the bottom cover on the Mavic air 2... There are two round sensors on each side of the LED. When you take the bottom cover off, do those have glass in them or are they just empty holes? In other words, is there supposed to be glass covering the glass sensors? Thanks
hi do you have idea if the air 2 core board mother board same with the air 2s mother board? can they compatibly replace each other? thanks from the philippines here
Hello. I bought a wrecked drone online and it is binded to an other acount. Would you recommend to change the motherboard in order to fix my drone or do I have to change other parts as well? Thanks
its a brushless motor DJI do not release schematics, if the USA push the right to repair bill and legislate we may get some then, size and power can be found in the specs of the drone on the DJI website :)
Yeah, if people want to see that in a future video please like this comment or add another comment and if we get enough requests we'll make one. These videos are pretty expensive to make though as they take a lot of time to do properly - this one took about 15 hours!
Hi DroneOptix, thank you for this guideline. Really appreciate. I have some questions. Basically, due to new European regulations, I need to decrease 570 grams weight of the Mavic Air 2 to 500 grams. I have an idea to get rid of avoidance sensors (Front,Down,Rear). Related to the above, the questions as follow: 1. Is there a chance to measure the weight of each module are shown in the video: - Front vision module (2:27) - Down vision module (1:02) - Rear vision module(4:10) 2. What are the parts may be considered as redundant? Just in case if avoidance sensors will not cut 70 grams. 3. In case I remove 3 mentioned modules and disable the avoidance sensors in the setting of the app. Would it be working fine? 4. Is the a chance to remove - Rear vision module(4:10) without unsoldering work? Thank you a lot for any information. it will help me a lot to make a decision. I believe for many people in Europe that would be helpful, due to the new European restrictions (valid from 1 July 2020) with drones above 500 grams. Thank you a lot
Sorry, but we don't have all of the parts in stock right now to carry out that weighing. We also don't know if the drone will still work without those sensors, but it should.
4:35 are the cords on the led of the landing leg a clip on or do they require soldering? I managed to crash my mavic air 2 and the leg broke. The antenna cord is still intact BUT the two led cords have disconnected
at 0.18 timeline, when you remove the bottom, do you see sealing to those screws to prevent unauthorised unscrewing so that once remove, warranty will be void? I suffer warranty void because of simply accusation of missing seal caused by me.
Is it easy to tear down the landing gear stand? Just concern, if I need to replace this part, does the LED come out easily or do I need to desolder the wires to remove it from the housing?
Yes, it's really easy, so long as you are happy taking the drone apart like shown in the video. We have them here - droneoptix.repair/product/brand-new-and-original-dji-mavic-air-2-backwards-vision-module-sensor-genuine they'll be in stock very soon.
Hi, yes we have one. The full camera gimbal is £299.99. We are getting them listed soon, but if you want to reserve it please pay the money through this page - www.droneoptix.repair/product/pay-a-bill
Please check out our site for parts and repairs droneoptix.repair
Best teardown viddy yet. Thanks, many questions answered especially as it relates to screw placement.
Very informative and helpful. Thanks
Bravo the best Tear-down video on YT...
thank you so much for your comment :)
Can you please do gimbal teardown?
Thank you)
Hello there. Can show how to disassemble the MAVIC AIR 2 REMOTE CONTROL. TQVM.
Hello, excellent video. I would like to know if you have any part of mavic Air 2s. I need upper front vision module. Thank you
Melhor vídeo até a o momento de desmontagem sem danificar o aparelho . Parabéns.
Good video sir
Thanks for the vid!!!! Very helpful replacing both left arms! Might want to mention that you need to put the front shoulder joint (?) in the half way position when reinstalling to preload it. Also I found if you pry up slightly on the ears (?) at the rear of the top shell, it comes off MUCH more easily.
hi mate, can you please run me through this half way position? like does the armm need to be in the open position? also what are you using to turn the joint. ive been stuck for a long time now. thanks
@@SuperAirman24 The rotation shaft is the little silver "can" with black plastic tee on the top (looks like a servo arm) You can see him pushing it out at (3:34) and the other arm's joint is on the table near his middle finger knuckle. Its the pivot and connection point for the front arms.
Hold the "can" gently with a pair of pliers and with another pair to hold the arm. Rotate it gently and you'll feel it lock into position every 180 degrees. By "halfway" I mean the point between locking positions. It'll hold itself there if you're careful. Then install it on the drone with the arm partially open (it only fits one way) and push it down onto the tits where the black arm seats.
Clear as mud huh? I've got one coming in tomorrow and I'll post a vid. If pictures are worth a thousand words and a vid is at least 10k. cheers
I was able to figure it out but man it was a pain to put back.
Hi can you make a similar video on putting back all the disassembled parts and getting the drone in working mode ( And can you pay special attention on soldering of the wires on mother board ) ?? Thank you
Just watch the video backwards
Wao!!! Buen video bro!
Do you have a teardown of the Mavic pro would love to see one and how do you take the bell housing apart need to clean it
very cool man
Nice video thanks! I have been doing some comparisons between US and EU model to find out the ADS-B hardware. I cannot find anything different between the two models. As per DJI, US models come with ADSB rf circuit and additional antenna and a different ESC powerboard
Hello, excellent video, can you confirm where exactly the compass is located? Thanks
Thanks very helpful video, keep it up :)
Hello, very good video, I have a big doubt, I want to know if you know where exactly the compass is located in the Mavic Air 2, I had a similar doubt with the compass of the Mavic Air v1 and after investigating more than 6 I was able to confirm that it was located in the main board, that is, it is integrated with the board. Do you know if the same thing happens with the Mavic Air 2 version? Thank you
Very thorough tutorial! One question, will any disassembled part require a calibration with special software after everything is put back together?
I believe that all the calibration needed is the one where u turn the drone.
Hello, is it possible to install an HDMI output in the Mavic Air 2 drone so that you can stream directly from the camera to the TV or PC? Thanks in advance
This can be done by an app, or perhaps plug from the USB port on the RC.
Does it have two antennas? One in each front leg? Or just one?
this is a better teardown than ifixits. proper.
Thanks so much for the feedback, it's really helpful. It's just a shame that their video became so much more popular.
Question about the bottom cover on the Mavic air 2...
There are two round sensors on each side of the LED.
When you take the bottom cover off, do those have glass in them or are they just empty holes?
In other words, is there supposed to be glass covering the glass sensors?
Thanks
What are the blue things on the bottom shell towards the rear? I’m not talking about the LED lights or the sensors but the mirror-like things
Does anyboby know what processor (or SoC) is installed in subject?
hi do you have idea if the air 2 core board mother board same with the air 2s mother board? can they compatibly replace each other? thanks from the philippines here
Hello. I bought a wrecked drone online and it is binded to an other acount. Would you recommend to change the motherboard in order to fix my drone or do I have to change other parts as well? Thanks
where can I get tools for the magic air 2S. the one I bought from amazon cam with stripped bits now its too late to return.
what type of motor is it? Schematics?? size and power??
its a brushless motor DJI do not release schematics, if the USA push the right to repair bill and legislate we may get some then, size and power can be found in the specs of the drone on the DJI website :)
Can you teardown the gimbal too ??
Yeah, if people want to see that in a future video please like this comment or add another comment and if we get enough requests we'll make one. These videos are pretty expensive to make though as they take a lot of time to do properly - this one took about 15 hours!
@@droneoptix5218 Yes It would be nice to see gimbal teardown. This video is even better then ifixit
Motherboard,gps,cameras,sensor,powerful motors,those reasons dji drones are very expensives
Where is the Compas located?
Hi DroneOptix, thank you for this guideline. Really appreciate.
I have some questions. Basically, due to new European regulations, I need to decrease 570 grams weight of the Mavic Air 2 to 500 grams. I have an idea to get rid of avoidance sensors (Front,Down,Rear). Related to the above, the questions as follow:
1. Is there a chance to measure the weight of each module are shown in the video:
- Front vision module (2:27)
- Down vision module (1:02)
- Rear vision module(4:10)
2. What are the parts may be considered as redundant? Just in case if avoidance sensors will not cut 70 grams.
3. In case I remove 3 mentioned modules and disable the avoidance sensors in the setting of the app. Would it be working fine?
4. Is the a chance to remove - Rear vision module(4:10) without unsoldering work?
Thank you a lot for any information. it will help me a lot to make a decision. I believe for many people in Europe that would be helpful, due to the new European restrictions (valid from 1 July 2020) with drones above 500 grams.
Thank you a lot
Sorry, but we don't have all of the parts in stock right now to carry out that weighing. We also don't know if the drone will still work without those sensors, but it should.
4:35 are the cords on the led of the landing leg a clip on or do they require soldering?
I managed to crash my mavic air 2 and the leg broke. The antenna cord is still intact BUT the two led cords have disconnected
India me aa jayega
Just crashed mine after connection error now i need a replacement camera signal line connected to the gimbal
Where can I get the front cover? Mine is bent and requires replacement. Please help!
Hi, we have one here
www.droneoptix.repair/product/brand-new-and-original-dji-mavic-air-2-front-plastic-cover-genuine
Hi how to disassembled motor and clean it. There are a sand
can the gimbal be replaced/repaired without purchasing an entirely new camera?
Yes it can, unfortunately most of the parts aren't avaliable to do it yourself.
What about the cam? :(
My dji drone of mavic air 2 GPS board has damage that make drone to fly .pls how can get a new one I mean GPS board
at 0.18 timeline, when you remove the bottom, do you see sealing to those screws to prevent unauthorised unscrewing so that once remove, warranty will be void? I suffer warranty void because of simply accusation of missing seal caused by me.
Hello,
Same over here !
Did you find a solution for this ?
Where can I find the vibration absorption bracket for the mavic air 2? Any help will be appreciated
www.droneoptix.repair/product/genuine-dji-mavic-2-vibration-gimbal-mount-board-frame-oem/
Is it easy to tear down the landing gear stand? Just concern, if I need to replace this part, does the LED come out easily or do I need to desolder the wires to remove it from the housing?
Hey,
The LED can be pulled out without soldering
I have a question where is the ads b in ma2
Do you ship parts to France?
Yes we do
Need mavic air 2 mother board
Is it the same for the Mavis air 2S?
the air 2s is different
I crashed my one of my rear sensors, is it easy to replace it?
Yes, it's really easy, so long as you are happy taking the drone apart like shown in the video. We have them here - droneoptix.repair/product/brand-new-and-original-dji-mavic-air-2-backwards-vision-module-sensor-genuine they'll be in stock very soon.
Hi, ı Need Mavic air 2 gimbal camera? Con you help me
Hi, yes we have one. The full camera gimbal is £299.99. We are getting them listed soon, but if you want to reserve it please pay the money through this page - www.droneoptix.repair/product/pay-a-bill
Hi, we have it marked in stock now here - www.droneoptix.repair/product/brand-new-and-original-dji-mavic-air-2-camera-and-gimbal-assembly-genuine
second
First
music is way too loud compared to the talking
Thanks for the feedback
Thank you 👍🏻