How to install solid vinyl soffit in the gable end
Вставка
- Опубліковано 19 жов 2024
- www.doityoursel... presents this tutorial how to video about how to install solid vinyl soffit along with some tips for a better job.Disclaimer: In my videos I don’t always use the safest methods of accomplishing whatever the video is about. I have been doing this type of work for over 30 years and I try and show the average homeowner how to accomplish whatever job is at hand. Therefore, if you choose to do something I show in my videos, please use all safety precautions as I will not be held responsible for your safety.
Disclaimer: In my videos I don’t always use the safest methods of accomplishing whatever the video is about. I have been doing this type of work for over 30 years and I try to show the average homeowner how to accomplish whatever job is at hand. Therefore, if you choose to do something I show in my videos, please use all safety precautions as I will not be held responsible for your safety and if you don’t like how I might be doing something that you deem unsafe, please keep your comments to yourself.
Check out my other videos:
• How to change a water ... How to change a water heater element
• How to caulk trim befo... How to caulk trim before painting
• How to Build a Soffit ... How to build a soffit and fascia return
• How to cut and glue CP... How to cut and glue CPVC pipe
• How to cut a hole in d... How to cut a hole in drywall for an electrical outlet
• How to cut quarter inc... How to cut quarter inch Hardie Backer board
• How to cut tile with a... How to cut tile with a manual tile cutter
• How to Flash a Window ... How to properly flash a window before new window installation
• How to enlarge an open... How to enlarge an opening on a non-bearing wall
• How to get a good qual... How to get a good quality paint job on a wall with how to paint a straight line when cutting in
• How to hang or install... How to hang drywall on a crooked wall
• How to install a doork... How to install a door knob and dead bolt
• How to install a Delta... How to install a Delta rough in valve using CPVC
• How to Install or Hang... How to install or hang Wire Shelving
• How to install a drain... How to install the plumbing drain for a washing machine in a remodel job
• How to apply alkali re... How to apply alkali resistant tape to concrete or Hardie backer board
• How to install a drop ... How to install a drop-in tub using concrete mortar as a support base
• How to install a pocke... How to install a pocket door in an existing wall
• How to install a solid... How to install a one piece or solid jamb door
• How to trim out a pock... How to install trim on a pocket door
• How to install a Vinyl... How to install a vinyl gable vent
• How to install a new c... How to install a new construction vinyl window
• Video How to install an Aprilaire humidifier with ductboard or fiberglass
ductwork
• How to Install Base Tr... How to measure, mark, and cut base trim inside corner using a coping saw
• How to install concret... How to install concrete board or hardi backer board on the ceiling and walls in a shower
• How to install dimensi... How to install dimensional shingles on a roof and valley
• How to install mosaic ... How to layout and install mosaic tile on a shower ceiling
Good video
Thank you.
Start at the peak and work your way down both sides. You're eyes are drawn to the peak where the panels will be even.
That would be good too.
Interest to see the j-channel... Why not install the soffit the long way?
Soffit comes in a width of 12 inches. This soffit is only 8 inches wide. So, you would have to cut off the nailing flange. So, it would not be very secure. I have never seen it done that way, I have only seen it done the way I showed.
@@doityourselfdenniscom thank you for the reply. The one I got from Lowe's is about 13.5 inch wide and like 11 ft long... I was wondering bc like you mentioned I have only seen it on UA-cam the way you put it up and not the way I put it up lol I just wanted to make sure I didn't do it wrong, and if I did, I'll fix it since I only put one piece... I'm curious to see how you finished the soffit with the J-channel.
@@gianelpibe The finished part of the soffit you bought at Lowes should only be 12 inches wide, then when you add the nailing flange on that would make it the 13.5 inches. If you do it the way I show, the J-Channel will just butt up against the soffit after the soffit has been hung.
should have used a piece of starter strip...!
Not a bad Idea, ust wasn't taught that way.
I've always put my j channel 0n first
I like to put my soffit on first and butt my j channel up against the soffit.
Lmao what the fuck you don’t even any soffit jay channel on there
NOT the correct way to put up soffit! J channel is placed first...then soffit placed in it and etc. This video is a perfect example of what NOT to do to put on soffit.👎
This is just another opinion. Say someone does it your way. Then you have to put up more j channel to accept the siding. Why use two pieces of j channel? The way I do it is better.
This way is also more resistant to wind and animals
Why no f channel?
Because there will be j channel will be butting up against the soffit, therefore f channel is not needed. Hope this helped.