Maybe it's just me, but I had figured most of this stuff out myself. A couple other tidbits he didn't mention are, when entering the cut, I manually lift the blade guard, until the guard is on top of the work, so "bumping" the guard against the work doesn't cause a wiggle at the entry. The biggest thing is, I guide the front of the saw with my thumb on the side of the shoe...and yes, I still have all my fingers. This gives the front more stability when super straight cuts are needed. I ripped down a couple old solid wood doors, free hand, for my son's house this weekend. I don't think we could have cut them much straighter on a table saw without a BIG table.
@@PayNoTaxes0GetNoVote these are some key things imo that should have been added to the video👍. I do the exact same thing when cutting kitchen counters, doors etc freehand. Its funny that I also had to figure that out for myself just like you😁. The only thing people told me about freehand cutting as an apprentice carpenter was to watch the blade/teeth instead of the guide. It would have helped me tremendously if I had been given these pointers at that time.
agreed. using a circ saw since 1979. i'd say though, when cutting a short(er) freehand line, set up with two hands on the saw and do not use your arms - position yourself so you can bend at the waist while your arms are locked in position. it's the only way it works for me. and don't even try a long freehand, it won't work.
I read that wrong, I thought he was saying literally before HE was born I was going to ask if it was a self C-section. I probably bought my circular saw before he was born.
That was great,,,"wood Butcher" I havent heard that since I was called one back in the 80`s,,,,(which i wasnt) And retire as a Master Trim &Cabinet maker
I started this video thinking you were going to tell me I've been doing it wrong. It's a good tip, but I have always done it that way because it just makes sense to me. Lining up the blade and the front of saw with your cut gives better accuracy cause you are aiming with 2 points. It's like rifle sights. The farther the two aiming points are apart, the more accurate you can be.
When you turn your saw upside, open the guard and start touching the blade you might want to remove the battery first. ( From a 59 years old carpenter who still has all his fingers attached.)
Great advice as always. Knowing the thickness of the blade is critical. Right vs left side cuts can therefore be different, in case exact matching is critical. Awesome tip with the ruler. I’ve now scored the other side of the blade on the leading edge of the guide.
That's what I do on my table saw, I measure from the edge of a tooth to my fence or if I have a line I put the edge of one of the teeth exactly on the outside of the line. So far I get perfect accuracy when doing that
--- he made both cuts with the blade to the right of the line meaning he took one line and left one line - if blade width was critical he should have cut the top line after cutting the right line, then flipped the piece 180 and cut the former left line which would now be on the right
Great tip on using a straight edge on checking blade lineup to notched indicators. Need to do one for 45 angle cut with a circular base plate notches. I have used saws with the notch slightly off. Never thought of using a straight edge. Nice!
I've had to go so far as to invest in a straight-edge, a sharpie, and some clear nail polish for the 45... Set up the saw appropriately and then use the straight-edge to align with the teeth. They can be upwards of a 32nd to the side of the body of the blade... When you compare to your notch, use the sharpie for any necessary corrections on the very edge of the base plate... THEN you can flip the saw to put the line where you NEED it. A stroke of nail-polish will act like urethane clear coat (I happen to love Covergirl for the life-span vs. price) so it won't rub right off again... Try a test-cut to confirm it, of course... AND the clear polish will be dry usually in about 10 - 20 minutes or so, even less on a hot day outside. At least, so far... that's been my favorite method... AND it works on "cheap-o" saws that are really off for the "general purpose" cuts, too... (Thanks China)... ;o)
The idea of not just looking at the saw blade, but looking ahead a few inches also to make sure I’m in line was really a game changer for me when cutting ceramic tiles with a wet saw table. I could suddenly cut easier and straighter when before I was very frustrated at how crooked my cuts were.
For me cutting along the straight line was always a struggle until I checked a few things. If a straight line feels like a struggle check the straight line mark at the back of your blade and where the rear of the blade and the mark are relative to the drawn line and your technique. Also check pinching from wood compression or lack of support. A pinched blade can force the cut off course. Technique includes overreaching, a poor or uncomfortable standing position, and a slanted view of the cut line. In addition to your great tips marking and checking the lineup and bevel at the start of each day (and after each oops/drop of the saw) this weekend guy learned these and so many more from a lifelong carpenter and framer. Thanks for your great tips and quality videos.
Very handy tip. Thank you! When it comes to circular saws, table saws etc., I am paranoid about safety, kickback, etc., so absorb a lot of these videos in advance.
Then don’t follow his advice to nudge the saw back a little. That can easily go bad, once you’ve started cutting you need to commit. I find that good posture and positioning of yourself makes a world of difference.
Also don't use your finger as a guide as he did. Don't get your hand anywhere near that blade. Skilsaw, table saw, and cut-off wheels/grinders are the most dangerous tools.
THANK YOU ! I have been using circular saws for over fifty years. I gave up on trying to get accurate cuts about 45 years ago and have only been using them for rough cuts ever since. I would always get screwed up as to where to line up the notch, and then would have trouble keeping the saw in line with my pencil mark. That ruler trick set off the proverbial light bulb in my head. Thank you and wish me luck on my next saw cutting endeavour.
@@teedachosenone6815 I gave up on chasing the newest and best technology a long time ago. Ever since I realized that manufacturers are playing us into buying something we already had by timing new releases of tech. Or worse yet cordless tools where you have to replace the battery ever once in a while. I'm in most cases still using tools that I bought thirty or forty years ago. That leaves a lot of cash left over.
Great point about taking a straight edge and confirming the exact relationship of the blade to the guide tick. I'll confess that I've gone years with circ saws without confirming this and just kind of allow that the margin of error will be an 1/8th. It's really not a problem for the things i'm usually cutting with a skil saw... but it's worth the effort to fix.
Just a point to remember, the blade stock itself is narrower than the carbide teeth so use the correct side of the teeth to line up on with your straight edge, otherwise you might be off by a 32nd or so.
I learned as a shop carpenter to put the mark on the line saw rear raised up with the guard pulled up. And the blade over the work. Drop the back of the saw down and set on your line. Lift slightly, start saw and plug cut down into the work. Then move backward if necessary (try to cut to cut complete at plunge) then forward to complete the cut.
Very true, now try this. Place the cutout on the line as per the vid. Now lift the back of the saw, whilst pivoting it on the cut out/line point, until the bottom of the saw blade is level with the top of the material surface. Slide the pivot point forwards, along the line, until the blade is an 1/8 from the edge of the material. Sight along the blade to ensure you are inline with the cut you want to make. Support the pivot point with your spare hand, in a safe manor, start the saw and plunge the blade into the work piece. You know have half the saw blade smack on the line you want to cut. Works a treat every time.
you lost me at "now try this". lol. I'm just a butcher cuttin' big pieces into little pieces. If you have the time, maybe explain it a bit clearer or not. Thanks.
@@meatmaster8636: You’re not the only one, lol. I’ve been a professional carpenter and renovation contractor for decades and have no idea what this nonsense is about. I’ve learned to almost shave with a circular saw (not recommended) but I don’t have a clue what this was about. If you want a rough cut you can use the plate notch but if you want accuracy you never take your eye off the blade and the cut line and you use both hands to guide the saw, one on the trigger handle and the other on the horn. Simple as that.
@@rayray8687 Hi there, l think what he's trying to say is just basically use the _Old Piece_ as a JIG, & just run Your blade around it keeping an eye on the line of your _New Piece_ , which would be underneath, kinda like you would use a Router, . . *Disclaimer* : Interpretation & not advice..😉
As a framer that is constantly using different circular saws, I recommend just watching the blade and starting your cut slowly. You can whittle a tiny "error" on the unused piece as you ease the blade in straight. Battery saws are much less powerful and demand way straighter cuts than most jobs need. 120v AC is so much better. If you really need to be precise and slow, you may as well use a table saw or a miter saw and get a laser beam cut. You often don't want those on a framing jobsite though, bulky and slow.
For framing I would never not use 120v For what he's doing in this video I just use my table saw, unless the piece is gigantic, then I do use the circular saw, but with a track/jig I made.
My Makita trim saw cuts exactly 1.5” from the left side and 3.5” from the right side. For mission critical cuts I clamp a level to the board 1.5” or 3.5” away and just butt it up to the level for perfectly straight cuts. Or just pull out the track saw.
@@chrisallen6010 Dewalt, makita, milwakee, and most higher end saws have those distances same, i think they standardised them, but alwas worth checking that to be sure.
Last I knew Your Makita doesn't have a parallel adjustment for the base (Dewalt does if memory serves correctly). So, depending on the individual saw the numbers are problematic.
As a professional carpenter/ cabinet maker of 35 years, always use a straight guide when possible, OR cut line of sight to the blade, have good lighting when you cut. It also matters how critical the cut needs to be.
Great video on freehand steering. Couple of other points: Using the left hand on the baseplate and putting it near the blade could be a danger for the inexperienced. Worth explaining why you have a left bladed saw, I noted on the final cut you did correctly walk round the piece to keep the heavy motor above the bi to clamped to the desk which was good. Many thanks for your channel
Glad you used the right terminology: left bladed saw instead of left HANDED saw. The right bladed saws have been used for decades and IMO they are wrong right off the hop. You shouldn't have to lean over and look on the opposite side of the motor to see where you're cutting. I find it odd how the majority of cordless are left bladed and corded are right.
Great tip. For new kids on the block, remove battery pack when working on blade/saw for extra safety. Also give the cost of 3/4” plywood, Delrin is a great and permanent alternative for your friend’s boat.
Thanks man! I just started doing carpentry for work and have no clue about cuts and all. You help me with this so I appreciate it. I feel more confident in myself and that makes me to have a better day
Useful advice on lining up the cut, thanks. If I was a 'Safety Troll' I might suggest that holding a steel rule against the blade with the saw inverted, without removing power (battery) is not good. Even worse is using your middle finger for alignment (2:43) leaving your unrestrained thumb and index finger within reach of the blade. Remember: Rust never sleeps, gravity is always waiting, and sharp tools are watching your eyes! Lucky for you I'm not a Safety Troll. :o)
Cannot believe I never realized this “ two points” as a way to get started online….🤦🏼♂️.. also , I ever trust the plate notch, especially when using saw after a long absence or another saw I don’t use often. So I’m always using the blade to start ,move a few inches to see if tracking properly then I look to see where the notch is in relation to the blade line…the ruler method is gold . In fact I plan on doing g this on my new makita then marking the plate somehow to remind where to line up cut line ….simple, good advice right there ,Ty.
good video. Except when my dad taught me to use a circular saw, there was significantly more cussing. I think 95% of people get that wrong, if you are not cussing, you are not cutting.
Video mark 0:42 He grabs the "saw blade" with his left hand, while THE BATTERY IS CONNECTED TO THE TOOL! If you are going to TOUCH "ANY" TOOL BLADE, remove the battery or unplug the tool.
I have over 35 years experience using a circular saw and your lesson is superb. I have several circular saws and my favorite remains to be my Makita 5008NB 8-1/4-Inch. One of the best saws ever made.
I think I had convinced myself that circular saws simply are not accurate tools so I didn’t bother learning how to use it well for the few times my work called for it. Thanks for setting me straight! 😂
I am thinking of purchasing a jigsaw or a circular saw, good thing I have been on this video and learnt that I need the circular saw because I am more of a straight cutter than a curve cutter
Always wondered why my cuts were off by a little bit. So I just used your method to check the saw (skilsaw). Sure enough it was about 1/32 off. Now I know how to adjust for it!
Are you kidding...Just watch the blade..the blade is doing the cutting !...not the guide at the front.. Surely you can work this out after it doesn't work on previous cuts.There is no point in using the guide if you are not getting a cut on the line you have marked. Your comment was funny to read !
Actually, there are two notches on the front of the saw shoe, an outer notch that you pointed out and an inner notch just in front of the blade. It's much easier to line up the two notches on the cut line than watching the front notch and blade.
I have never saw straight with a circular saw, nor with a jigsaw.Thank you Je n'ai jamais scié droit avec une scie circulaire, pas plus qu'avec une scie sauteuse.Merci
I see a few things I would call out on this one. #1 Set the depth of cut for the material you are cutting to prevent kickback. #2 Don't depend on the guard retracting at the end of the cut - you shouldn't set the saw down on the guard after you make the cut.
What you show is a good tip FOR THAT situation. My critique is that there are 6 possible trajectory alignments for any cutting situation DEPENDING ON SITUATION. As a builder with a broad variety of cutting situations, one may at times need to cut to the LHS or RHS or centre of the line. And, one can be cutting with the wider saw sled on the waste or the keep side of the piece. Yes, your dual align tip is good, but some saws have a guide notch for LHS, RHS, or centre of blade tooth. Also blade teeth kerf can vary muchly (thick, thin) not always matching the notch perfectly. Life is never as simple as one YT demo.
Another tip is to set the blade height correctly and not have far to much blade spinning below the wood as in this video because this increases tear out.
Great stuff! You can't have a straight line without 2 points of reference and you demonstrated that perfectly in order to get the saw tracking right. Even with hand saws, your first 10 strokes are vital when it comes to getting a straight cut all the way down. Great explanation :)
i always get squirrely when the front guide on the base plate reaches the end of my pencil line and i then have to focus solely on the blade for the last few inches of the cut... in your example i would tweak your suggestion by extending the angled pencil lines past the cross line so i can follow the plate guide through the entire cut... i know that's not always possible when you are cutting to the end of your workpiece but maybe even butt a sacrificial piece to end of the workpiece to extend the pencil cut line?..... thanks for the great video!!
Once the blade is sunk into the work it should track straight in the kerf. He points out that it's important to start out aligned with the cut. Because if you're off track to start off with then it's harder to get on the line and your kerf won't be tight then either. If I want a straight line I use a speed square. If I really want a straight line I leave some meat off the line and plane to the line. If I really don't care then I freehand the cut.
When I want a truly straight cut, I take the time to set up a guide. YES, it is a little more work but the more often you set up a guide the faster you get at doing it well. If you held a straight edge along the cut, you'd see just how not straight those cuts are :-). Freehand "straight" cutting never really is, though probably 90+% of the time it is good enough.
Largely depends on the material - you will get varying degrees of break out. If the aesthetics of the finished cut are not critical then a single pass with the saw is normally ok. It is usual to scribe the cut line with a knife and cut up to that to minimise break out if a better finish is required. I would us the latter method and finish with the plane to guarantee the best outcome.
@@TheFunnyCarpenter: The real solution is to use the notch only for rough cuts. If you want accuracy, use a clamp-on straightedge cutting guide ($20.00) or follow the actual blade, not the notch.
I find lining up the blade, then putting my metal ruler next to the cutting plate and securing it with a clamp, gives me straight cuts every time while saving a lot of time. I can cut fast and accurate. I also wouldn't cut into the board which will be left over because that's easily 2cm of wood wasted. I'd cut the piece I require off first, then cut the pieces. Clamps are pretty awesome and can save you expensive wood and lots of time.
Here's a tip. Don't flip your saw over, pull the blade guard and place a metal ruler next to the blade WHILE YOUR SAW IS CONNECTED TO ITS POWER SOURCE. Geezus.
I do a variation where I line the marker up well into the work and drop the blade down onto the line. That gives me a cut blade length at the beginning that's perfectly straight and stops the small wobble we can do sometimes that binds the blade up and can heat and warp it, which makes it really hard to be straight after that. Or a thick blade that won't warp is good too lol.
Now this is how a truly seasoned and experienced professional cut guy does it! Its the only way to be both quick and accurate. I rarely start off the work unless im cutting something short like cripples or studs...sheet goods are always line up, plunge, and go.
A couple clamps and a straight edge makes the straightest cuts with my skill 77. Been doing it for 40 years or so! I build cabinet parts for repairs using this method, cut doors and other perfect cuts using this method. One really important thing to good cuts is a really sharp blade! Of course more teeth makes for better cutting in finer use applications as I'm sure you know. And treating ones blade with care helps them last longer, staying sharp for more great cuts! Since the carbide tipped blades have become so common one doesn't have a choice in blade cutting surface angled as when we did out own sharpening as my father taught me , it's been so long since I have hand files a blade it's not funny. Couldn't find my blade set tool without some searching lol. God Bless you and what you do!
Track saw hadn't been reagily available for all that long and my 4' level an two medium clamps are handy no matter what. Plus it's great for cutting doors , the one thing that's critical, a sharp blade perhaps some masking tape and a tape measure. I know the exact distance from the short side of my saw to the inner blade edge so it's super simple and requires no bulky extra parts!
@@jasnonya3005 I've been doing the clamps for a while and measuring the distance from blade, Its 29mm but it's always out 1 or 2 mm no matter what which is frustraighting as hell I got lent a makita track saw on site and it was quicker and perfect everytime, I'm still an apprentice though, not sure what's going wrong..
@@audibleadventures9004 I've the same skill worm drive I've used for at least 30 years it's second hand and I still draw a line or scribe it with a razor knife so I can see exactly where I want my blade edge to be for that reason!
I use a Kreg Saw guide and measure the left side from the edge to the blade and clamp the guide to the wood, this allows be to mage an 8’ cut as straight as a panel saw. I don’t have room in my home shop for a panel saw. I really enjoyed this video. We can learn something every day. Thanks I I subscribed and liked this video.
Trying to cut 45 degrees for 2 meter by 0.56 meter frames from 35 X 35 mm wood with a circular saw, finally convinced me that I'm not a carpenter. Rather use metal, as I can weld up the holes and faults.
2:42. Thumb on the guard with fingers on the board works as long as the saw doesn't bind. If the blade should bind and should you jerk the saw? Not to worry ... you've still got that extra thumb on your other hand. Fully gripping the guard alone, is as far as I've been willing to stretch it.
Being right handed and wanting to be able to see the blade was one of the reasons why I specifically bought my Bosch GKS 18V-Li instead of one of the newer models. The other reason is because it supports tracks right out of the box...
Great advise , many thanks . But i had to learn the hard way , because i bought a cheap mini circular saw , and the marketing was brilliant , shame the saw WAS NOT ....your advise about putting a steel ruler along side the blade to check alignment was bang on as the saw i bought was about 2mm out of parallel to the base , consequently the blade was stalling in the cut and over heating and a straight cut was never going to happen . Thank you ........
back in the day , we had thicker blades ( that did not warp during extensive use on a hot day) that were not always lining up with the saws' guide notch ... you are correct that some of us actually watch the blade as its cutting !!!
Ok, Funny Carpenter. You show on the open Blade of a Circular Saw, which Markpoint we should remember, to do the right cut. right? On the open Blade and with adapted Akku.- Bravo. This is, what every diy guy needs. People who show, how we better not should act, in case, we don't want to loose fingers, hands or arms. bravo!!!
Come on , you already have the piece clamped to your workbench just use a straight edge and you can't go wrong. You can be half blind with that method. This way makes no sense to me unless you are just rough cutting Lumber
Some good additional comments already. I'd add the importance of rehearsing your movement and settling on a comfortable stance that ensures your movement of head, body, arms flows in a line - not unlike how they teach snooker and pool cue technique. Height of bench, clamps, material all matters for a clean, smooth, and safe cut. Lighting - direction, strength, whiteness. Ergonomics, lighting, etc matters everywhere: people working at desks all twisted and cluttered because they don't think of spending a few seconds when they sit down making sure chair, monitor, coffee cup, etc all in good positions; people speaking into microphones standing at a lectern or sitting in a Zoom meeting. Once the groove is established - it all goes well all day with no stiff back the next day
Sorry but a circular saw will NEVER give you a straight cut. You only cut about 1 and a half times the saw length so there is really no room for error. However any longer cuts and a circular saw is impossible to get clean straight lines with. You need a guide.
I've used a circular saw since LITERALLY before you were born, and THAT was a great tip. Thank you. Thumbs up!
0pp lol kaka kiki íiiw8i8 it out iií1o990llll pool 1llp0lll
Maybe it's just me, but I had figured most of this stuff out myself. A couple other tidbits he didn't mention are, when entering the cut, I manually lift the blade guard, until the guard is on top of the work, so "bumping" the guard against the work doesn't cause a wiggle at the entry. The biggest thing is, I guide the front of the saw with my thumb on the side of the shoe...and yes, I still have all my fingers. This gives the front more stability when super straight cuts are needed. I ripped down a couple old solid wood doors, free hand, for my son's house this weekend. I don't think we could have cut them much straighter on a table saw without a BIG table.
@@PayNoTaxes0GetNoVote these are some key things imo that should have been added to the video👍. I do the exact same thing when cutting kitchen counters, doors etc freehand. Its funny that I also had to figure that out for myself just like you😁. The only thing people told me about freehand cutting as an apprentice carpenter was to watch the blade/teeth instead of the guide. It would have helped me tremendously if I had been given these pointers at that time.
agreed. using a circ saw since 1979. i'd say though, when cutting a short(er) freehand line, set up with two hands on the saw and do not use your arms - position yourself so you can bend at the waist while your arms are locked in position. it's the only way it works for me. and don't even try a long freehand, it won't work.
I read that wrong, I thought he was saying literally before HE was born I was going to ask if it was a self C-section.
I probably bought my circular saw before he was born.
As a casual wood butcher (can't call myself a wood worker lol), little tips like this are priceless. Thanks!
This is not "little" tips this is (SPARTAAAAA) paid type content
That was great,,,"wood Butcher" I havent heard that since I was called one back in the 80`s,,,,(which i wasnt) And retire as a Master Trim &Cabinet maker
When I bought my saw and started making cuts the thing you showed here turned out to be absolutely intuitive.
I started this video thinking you were going to tell me I've been doing it wrong. It's a good tip, but I have always done it that way because it just makes sense to me. Lining up the blade and the front of saw with your cut gives better accuracy cause you are aiming with 2 points. It's like rifle sights. The farther the two aiming points are apart, the more accurate you can be.
When you turn your saw upside, open the guard and start touching the blade you might want to remove the battery first. ( From a 59 years old carpenter who still has all his fingers attached.)
Great advice as always. Knowing the thickness of the blade is critical. Right vs left side cuts can therefore be different, in case exact matching is critical. Awesome tip with the ruler. I’ve now scored the other side of the blade on the leading edge of the guide.
That's what I do on my table saw, I measure from the edge of a tooth to my fence or if I have a line I put the edge of one of the teeth exactly on the outside of the line. So far I get perfect accuracy when doing that
--- he made both cuts with the blade to the right of the line meaning he took one line and left one line - if blade width was critical he should have cut the top line after cutting the right line, then flipped the piece 180 and cut the former left line which would now be on the right
Great tip on using a straight edge on checking blade lineup to notched indicators. Need to do one for 45 angle cut with a circular base plate notches. I have used saws with the notch slightly off. Never thought of using a straight edge. Nice!
I've had to go so far as to invest in a straight-edge, a sharpie, and some clear nail polish for the 45... Set up the saw appropriately and then use the straight-edge to align with the teeth. They can be upwards of a 32nd to the side of the body of the blade... When you compare to your notch, use the sharpie for any necessary corrections on the very edge of the base plate... THEN you can flip the saw to put the line where you NEED it. A stroke of nail-polish will act like urethane clear coat (I happen to love Covergirl for the life-span vs. price) so it won't rub right off again... Try a test-cut to confirm it, of course... AND the clear polish will be dry usually in about 10 - 20 minutes or so, even less on a hot day outside.
At least, so far... that's been my favorite method... AND it works on "cheap-o" saws that are really off for the "general purpose" cuts, too... (Thanks China)... ;o)
The 45 cuts' variation from the notch is somewhat dependent on the width of the blade.
I been using a saw for many years. Had two accidents, now have one funny finger. Which compelled me to watch.
Good advice man! Thanks.
Great tip and appreciate the advice, I’m horrible at free cutting without a fence guide and angled cuts are a nightmare for me. Thanks
The idea of not just looking at the saw blade, but looking ahead a few inches also to make sure I’m in line was really a game changer for me when cutting ceramic tiles with a wet saw table. I could suddenly cut easier and straighter when before I was very frustrated at how crooked my cuts were.
For me cutting along the straight line was always a struggle until I checked a few things. If a straight line feels like a struggle check the straight line mark at the back of your blade and where the rear of the blade and the mark are relative to the drawn line and your technique. Also check pinching from wood compression or lack of support. A pinched blade can force the cut off course. Technique includes overreaching, a poor or uncomfortable standing position, and a slanted view of the cut line. In addition to your great tips marking and checking the lineup and bevel at the start of each day (and after each oops/drop of the saw) this weekend guy learned these and so many more from a lifelong carpenter and framer.
Thanks for your great tips and quality videos.
A free tip…..take your battery out before ever and I mean ever touching the blade!
Well since you mean it I guess I’ll do it
wish i saw this sooner, typing this with my nose rn
Very handy tip. Thank you! When it comes to circular saws, table saws etc., I am paranoid about safety, kickback, etc., so absorb a lot of these videos in advance.
Then don’t follow his advice to nudge the saw back a little. That can easily go bad, once you’ve started cutting you need to commit.
I find that good posture and positioning of yourself makes a world of difference.
Also don't use your finger as a guide as he did. Don't get your hand anywhere near that blade. Skilsaw, table saw, and cut-off wheels/grinders are the most dangerous tools.
THANK YOU ! I have been using circular saws for over fifty years. I gave up on trying to get accurate cuts about 45 years ago and have only been using them for rough cuts ever since. I would always get screwed up as to where to line up the notch, and then would have trouble keeping the saw in line with my pencil mark. That ruler trick set off the proverbial light bulb in my head. Thank you and wish me luck on my next saw cutting endeavour.
just what the blade .... that is all you need to do ... except hold the the saw steady
The new saws have lasers now almost impossible to mess up with the laser
@@teedachosenone6815 I gave up on chasing the newest and best technology a long time ago. Ever since I realized that manufacturers are playing us into buying something we already had by timing new releases of tech. Or worse yet cordless tools where you have to replace the battery ever once in a while. I'm in most cases still using tools that I bought thirty or forty years ago. That leaves a lot of cash left over.
Need luck if you've used for 45 yes. Can't get straight cut😅
@@PaulARGO-r5m A circular saw is not the only tool out there designed to cut wood.
It’s like the rear and front sights of a rifle, you need to use both to go straight. Good explaination👍
Great point about taking a straight edge and confirming the exact relationship of the blade to the guide tick. I'll confess that I've gone years with circ saws without confirming this and just kind of allow that the margin of error will be an 1/8th. It's really not a problem for the things i'm usually cutting with a skil saw... but it's worth the effort to fix.
As someone who typically does scrollwork with a circular saw this was immensely helpful.
@Hello there, how are you doing this blessed day?
Just a point to remember, the blade stock itself is narrower than the carbide teeth so use the correct side of the teeth to line up on with your straight edge, otherwise you might be off by a 32nd or so.
no one expects that kind of precision with a handheld circular saw
@@xl000 Craftsmen do.
That is the kerf? Correct? I’m learning :)
@BELIEVE in JESUS Are you feeling alright? 😂
You are so correct
I learned as a shop carpenter to put the mark on the line saw rear raised up with the guard pulled up. And the blade over the work. Drop the back of the saw down and set on your line. Lift slightly, start saw and plug cut down into the work. Then move backward if necessary (try to cut to cut complete at plunge) then forward to complete the cut.
Very true, now try this. Place the cutout on the line as per the vid. Now lift the back of the saw, whilst pivoting it on the cut out/line point, until the bottom of the saw blade is level with the top of the material surface. Slide the pivot point forwards, along the line, until the blade is an 1/8 from the edge of the material. Sight along the blade to ensure you are inline with the cut you want to make. Support the pivot point with your spare hand, in a safe manor, start the saw and plunge the blade into the work piece. You know have half the saw blade smack on the line you want to cut. Works a treat every time.
you lost me at "now try this". lol. I'm just a butcher cuttin' big pieces into little pieces. If you have the time, maybe explain it a bit clearer or not. Thanks.
@@meatmaster8636: You’re not the only one, lol. I’ve been a professional carpenter and renovation contractor for decades and have no idea what this nonsense is about. I’ve learned to almost shave with a circular saw (not recommended) but I don’t have a clue what this was about. If you want a rough cut you can use the plate notch but if you want accuracy you never take your eye off the blade and the cut line and you use both hands to guide the saw, one on the trigger handle and the other on the horn. Simple as that.
@@meatmaster8636 Sounds like he's saying not to start the cut on the edge of the board but to start with a plunge cut.
@@rayray8687 Hi there, l think what he's trying to say is just basically use the _Old Piece_ as a JIG, & just run Your blade around it keeping an eye on the line of your _New Piece_ , which would be underneath, kinda like you would use a Router, . .
*Disclaimer* : Interpretation & not advice..😉
@@stonerlokz: I think maybe you’re right but then some people can complicate a one-ticket raffle, lol.
As a framer that is constantly using different circular saws, I recommend just watching the blade and starting your cut slowly. You can whittle a tiny "error" on the unused piece as you ease the blade in straight. Battery saws are much less powerful and demand way straighter cuts than most jobs need. 120v AC is so much better. If you really need to be precise and slow, you may as well use a table saw or a miter saw and get a laser beam cut. You often don't want those on a framing jobsite though, bulky and slow.
For framing I would never not use 120v
For what he's doing in this video I just use my table saw, unless the piece is gigantic, then I do use the circular saw, but with a track/jig I made.
@@KuntaKinteToby you would never use a 120v? Most other people do. A table saw would be a pain tfd the ass for this. This method is far superior.
Nice and simple. Thanks for the tip about the straight edge; I never thought of that.
First thing is take the battery first !!!!! Inspection, cleaning, measuring!!!!
My Makita trim saw cuts exactly 1.5” from the left side and 3.5” from the right side. For mission critical cuts I clamp a level to the board 1.5” or 3.5” away and just butt it up to the level for perfectly straight cuts. Or just pull out the track saw.
I need to check those distances out on my Makita. I've built a saw sled for it but it's just too big for most cuts to be practical.
@@chrisallen6010 Dewalt, makita, milwakee, and most higher end saws have those distances same, i think they standardised them, but alwas worth checking that to be sure.
Last I knew Your Makita doesn't have a parallel adjustment for the base (Dewalt does if memory serves correctly). So, depending on the individual saw the numbers are problematic.
We enjoy seeing your work and we are happy to see and support our channel ...💙
As a professional carpenter/ cabinet maker of 35 years, always use a straight guide when possible, OR cut line of sight to the blade, have good lighting when you cut. It also matters how critical the cut needs to be.
I use a laser guide and squares.
Great video on freehand steering. Couple of other points: Using the left hand on the baseplate and putting it near the blade could be a danger for the inexperienced. Worth explaining why you have a left bladed saw, I noted on the final cut you did correctly walk round the piece to keep the heavy motor above the bi to clamped to the desk which was good. Many thanks for your channel
Glad you used the right terminology: left bladed saw instead of left HANDED saw. The right bladed saws have been used for decades and IMO they are wrong right off the hop. You shouldn't have to lean over and look on the opposite side of the motor to see where you're cutting. I find it odd how the majority of cordless are left bladed and corded are right.
Weren't the old heavy worm drive saws all left blade?
@@muskokamike127 Think it's a size thing. The smaller ones (easier to hold on to) are left bladed for good visibility (and poor holding)
Yes and Still are@@robs1852
I have both corded saws,,,1 leftblade motor and 1 right@@muskokamike127
For beginners like me a straightedge and two wood clamps will also help guide your so nicely.
Great tip. For new kids on the block, remove battery pack when working on blade/saw for extra safety.
Also give the cost of 3/4” plywood, Delrin is a great and permanent alternative for your friend’s boat.
Seen that straight away and winced, u wouldn’t do it with a mains tool so why different with a battery? Decent video though.
Thanks man! I just started doing carpentry for work and have no clue about cuts and all. You help me with this so I appreciate it. I feel more confident in myself and that makes me to have a better day
Here’s a tip for you. The handle on the front of the saw is there for a reason.
I found having confidence makes the straightest cut also great tip with the straight edge
Thanks for the tips dude, sometimes I don't know how I overlooked some of these but I'm glad guys like you are out there showing them to people.
Thank you for teaching the next generation!
Useful advice on lining up the cut, thanks. If I was a 'Safety Troll' I might suggest that holding a steel rule against the blade with the saw inverted, without removing power (battery) is not good. Even worse is using your middle finger for alignment (2:43) leaving your unrestrained thumb and index finger within reach of the blade. Remember: Rust never sleeps, gravity is always waiting, and sharp tools are watching your eyes!
Lucky for you I'm not a Safety Troll. :o)
That's a lot of words to say that the guy is a hack. The guy probably built a few bird houses and now he thinks he's an a youtube expert Carpenter
You forgot to mention that saws and other tools also hold grudges for non use, the longer you don't use them the more often they bite you. lol
Cannot believe I never realized this “ two points” as a way to get started online….🤦🏼♂️.. also , I ever trust the plate notch, especially when using saw after a long absence or another saw I don’t use often. So I’m always using the blade to start ,move a few inches to see if tracking properly then I look to see where the notch is in relation to the blade line…the ruler method is gold . In fact I plan on doing g this on my new makita then marking the plate somehow to remind where to line up cut line ….simple, good advice right there ,Ty.
good video. Except when my dad taught me to use a circular saw, there was significantly more cussing. I think 95% of people get that wrong, if you are not cussing, you are not cutting.
Video mark 0:42 He grabs the "saw blade" with his left hand, while THE BATTERY IS CONNECTED TO THE TOOL! If you are going to TOUCH "ANY" TOOL BLADE, remove the battery or unplug the tool.
You could also mention blade depth. makes a better cut and safer.
Indeed. As a good practice i keep my depth about half a tooth coming out the other side.
I have over 35 years experience using a circular saw and your lesson is superb. I have several circular saws and my favorite remains to be my Makita 5008NB 8-1/4-Inch. One of the best saws ever made.
NO ONE and I mean NO ONE asked for your opinion as to what saw is best. Please keep it to yourself ! ! !
Thank you @hootinouts for telling us your saw preference. I'm about to buy a used Makita and you positively influenced my choice.
Love from Montréal
85% of people using percentages in video titles have 100% just used any random number.
😂 true
I think I had convinced myself that circular saws simply are not accurate tools so I didn’t bother learning how to use it well for the few times my work called for it. Thanks for setting me straight! 😂
I’ve been using a circular saw for decades and I’m part of the 85%…thanks for the tip!
Thanks for checking out the video Steve🍻
I am thinking of purchasing a jigsaw or a circular saw, good thing I have been on this video and learnt that I need the circular saw because I am more of a straight cutter than a curve cutter
A jigsaw is way safer and you can get straight cuts with practice or use clamped on guide
Always wondered why my cuts were off by a little bit. So I just used your method to check the saw (skilsaw). Sure enough it was about 1/32 off. Now I know how to adjust for it!
Are you kidding...Just watch the blade..the blade is doing the cutting !...not the guide at the front.. Surely you can work this out after it doesn't work on previous cuts.There is no point in using the guide if you are not getting a cut on the line you have marked. Your comment was funny to read !
All these (many) years I mistakenly Ass-umed the line on the saw matched the blade! Great tip! And thanks for wearing ear & eye protection!
Actually, there are two notches on the front of the saw shoe, an outer notch that you pointed out and an inner notch just in front of the blade. It's much easier to line up the two notches on the cut line than watching the front notch and blade.
The second notch is how you line up for a 45
I’ve never seen anyone make the mistake he’s talking about. Including myself who never had any instructions on how to use these tools
Circular saw you say...what a great idea. I have a triangular saw and it sucks! 😀
Triangle saws are for cutting circles. I bet you think I'm joking. Go look it up.
I have never saw straight with a circular saw, nor with a jigsaw.Thank you
Je n'ai jamais scié droit avec une scie circulaire, pas plus qu'avec une scie sauteuse.Merci
I thought you were gonna talk about compensating for kerf thickness since you were cutting on both sides of a line there. Maybe I missed it
I like checking the blade/notch position with a ruler! Thanks for the tip!
I see a few things I would call out on this one. #1 Set the depth of cut for the material you are cutting to prevent kickback. #2 Don't depend on the guard retracting at the end of the cut - you shouldn't set the saw down on the guard after you make the cut.
Thanks Dad...
Gotta say, even though I was aware of this method, I’m still impressed with the execution.
Top drawer my good man.
Thanks buddy 🍻
What you show is a good tip FOR THAT situation. My critique is that there are 6 possible trajectory alignments for any cutting situation DEPENDING ON SITUATION.
As a builder with a broad variety of cutting situations, one may at times need to cut to the LHS or RHS or centre of the line. And, one can be cutting with the wider saw sled on the waste or the keep side of the piece. Yes, your dual align tip is good, but some saws have a guide notch for LHS, RHS, or centre of blade tooth. Also blade teeth kerf can vary muchly (thick, thin) not always matching the notch perfectly. Life is never as simple as one YT demo.
Been a carpenter for over 50 year's and thought exactly the same thing my friend...👍
Always take the battery out or unplug if power if you are dicking around near the blade
I figured this out on a job a few years ago. Only took me 25 years of regular use lol. Thanks for sharing. Appreciate ya
Another tip is to set the blade height correctly and not have far to much blade spinning below the wood as in this video because this increases tear out.
I agree , too much blade is dangerous .
Setting the depth to the thickness of the material reduces accuracy.
@@geoffprothero9408 setting it too deep is dangerous and causes tear out.
Great video. Probably best to isolate the power if placing fingers anywhere near the blade.
Great stuff! You can't have a straight line without 2 points of reference and you demonstrated that perfectly in order to get the saw tracking right. Even with hand saws, your first 10 strokes are vital when it comes to getting a straight cut all the way down. Great explanation :)
Over 30 years as a finish carpenter/cabinet maker...suck with a circ saw...rather proud of that!
i always get squirrely when the front guide on the base plate reaches the end of my pencil line and i then have to focus solely on the blade for the last few inches of the cut... in your example i would tweak your suggestion by extending the angled pencil lines past the cross line so i can follow the plate guide through the entire cut... i know that's not always possible when you are cutting to the end of your workpiece but maybe even butt a sacrificial piece to end of the workpiece to extend the pencil cut line?..... thanks for the great video!!
Once the blade is sunk into the work it should track straight in the kerf. He points out that it's important to start out aligned with the cut. Because if you're off track to start off with then it's harder to get on the line and your kerf won't be tight then either. If I want a straight line I use a speed square. If I really want a straight line I leave some meat off the line and plane to the line. If I really don't care then I freehand the cut.
To add to this… a sharp blade of the right type for the material… paramount to compliment this tip
When I want a truly straight cut, I take the time to set up a guide. YES, it is a little more work but the more often you set up a guide the faster you get at doing it well. If you held a straight edge along the cut, you'd see just how not straight those cuts are :-). Freehand "straight" cutting never really is, though probably 90+% of the time it is good enough.
Good tip nice and simple One thing iIwould say is extend you cut lines allows you to continue with your method past the end of you cut.
After I just dropped my saw this week on the concrete there’s no point lining up the front mark it’s of like 1/4” lol just watch the blade👍
Largely depends on the material - you will get varying degrees of break out.
If the aesthetics of the finished cut are not critical then a single pass with the saw is normally ok. It is usual to scribe the cut line with a knife and cut up to that to minimise break out if a better finish is required.
I would us the latter method and finish with the plane to guarantee the best outcome.
What about what to do if the blade isn't lined up with the notch? Great video!
You can make a mark with a black felt or etch something in there to help out.
@The Funny Carpenter oh. Dumb question on my part ha ha. I was thinking about adjusting or "trueing" the blade. Thanks!
Have a cheap old craftsman saw I 'fine tuned' the notch with a file for that very reason.
@@TheFunnyCarpenter: The real solution is to use the notch only for rough cuts. If you want accuracy, use a clamp-on straightedge cutting guide ($20.00) or follow the actual blade, not the notch.
@@Ian_Burt: That’s great but how do you un-file it if it’s out of alignment the other way, lol.
I am very thankful for this tip.
I find lining up the blade, then putting my metal ruler next to the cutting plate and securing it with a clamp, gives me straight cuts every time while saving a lot of time. I can cut fast and accurate.
I also wouldn't cut into the board which will be left over because that's easily 2cm of wood wasted. I'd cut the piece I require off first, then cut the pieces.
Clamps are pretty awesome and can save you expensive wood and lots of time.
Here's a tip. Don't flip your saw over, pull the blade guard and place a metal ruler next to the blade WHILE YOUR SAW IS CONNECTED TO ITS POWER SOURCE. Geezus.
Geat video thanks. My OCD kept telling me to do the horizontal cut 1st to save wastage.
Take the battery out first fella before u start lining up blade with guide mark. Safety 1st
Excellent demonstration
I do a variation where I line the marker up well into the work and drop the blade down onto the line. That gives me a cut blade length at the beginning that's perfectly straight and stops the small wobble we can do sometimes that binds the blade up and can heat and warp it, which makes it really hard to be straight after that. Or a thick blade that won't warp is good too lol.
Now this is how a truly seasoned and experienced professional cut guy does it! Its the only way to be both quick and accurate. I rarely start off the work unless im cutting something short like cripples or studs...sheet goods are always line up, plunge, and go.
A couple clamps and a straight edge makes the straightest cuts with my skill 77. Been doing it for 40 years or so! I build cabinet parts for repairs using this method, cut doors and other perfect cuts using this method. One really important thing to good cuts is a really sharp blade! Of course more teeth makes for better cutting in finer use applications as I'm sure you know. And treating ones blade with care helps them last longer, staying sharp for more great cuts! Since the carbide tipped blades have become so common one doesn't have a choice in blade cutting surface angled as when we did out own sharpening as my father taught me , it's been so long since I have hand files a blade it's not funny. Couldn't find my blade set tool without some searching lol. God Bless you and what you do!
Not find a track saw quicker and more accurate?
Track saw hadn't been reagily available for all that long and my 4' level an two medium clamps are handy no matter what. Plus it's great for cutting doors , the one thing that's critical, a sharp blade perhaps some masking tape and a tape measure.
I know the exact distance from the short side of my saw to the inner blade edge so it's super simple and requires no bulky extra parts!
@@jasnonya3005 I've been doing the clamps for a while and measuring the distance from blade, Its 29mm but it's always out 1 or 2 mm no matter what which is frustraighting as hell I got lent a makita track saw on site and it was quicker and perfect everytime, I'm still an apprentice though, not sure what's going wrong..
@@audibleadventures9004 I've the same skill worm drive I've used for at least 30 years it's second hand and I still draw a line or scribe it with a razor knife so I can see exactly where I want my blade edge to be for that reason!
I use a Kreg Saw guide and measure the left side from the edge to the blade and clamp the guide to the wood, this allows be to mage an 8’ cut as straight as a panel saw. I don’t have room in my home shop for a panel saw. I really enjoyed this video. We can learn something every day. Thanks I I subscribed and liked this video.
I use a straight stick and 2 clamps works great for me
Thanks…. Another great tip Funny Man.
That was a very good demonstration. Thanks.
Trying to cut 45 degrees for 2 meter by 0.56 meter frames from 35 X 35 mm wood with a circular saw, finally convinced me that I'm not a carpenter. Rather use metal, as I can weld up the holes and faults.
2:42. Thumb on the guard with fingers on the board works as long as the saw doesn't bind. If the blade should bind and should you jerk the saw? Not to worry ... you've still got that extra thumb on your other hand. Fully gripping the guard alone, is as far as I've been willing to stretch it.
That blade sounded as if it were getting trapped or struggling. Great tip about checking with a steel rule
Being right handed and wanting to be able to see the blade was one of the reasons why I specifically bought my Bosch GKS 18V-Li instead of one of the newer models.
The other reason is because it supports tracks right out of the box...
Great advise , many thanks .
But i had to learn the hard way , because i bought a cheap mini circular saw , and the marketing was brilliant , shame the saw WAS NOT ....your advise about putting a steel ruler along side the blade to check alignment was bang on as the saw i bought was about 2mm out of parallel to the base , consequently the blade was stalling in the cut and over heating and a straight cut was never going to happen .
Thank you ........
back in the day , we had thicker blades ( that did not warp during extensive use on a hot day) that were not always lining up with the saws' guide notch ... you are correct that some of us actually watch the blade as its cutting !!!
Also draw your guide line beyond your stopping point so you still have something to line that notch up with.
Ok, Funny Carpenter. You show on the open Blade of a Circular Saw, which Markpoint we should remember, to do the right cut. right? On the open Blade and with adapted Akku.- Bravo. This is, what every diy guy needs. People who show, how we better not should act, in case, we don't want to loose fingers, hands or arms. bravo!!!
i've been cutting wrong all this time
*Thank You*
Come on , you already have the piece clamped to your workbench just use a straight edge and you can't go wrong. You can be half blind with that method. This way makes no sense to me unless you are just rough cutting Lumber
Nope. If you want a guide for your saw table, you use your thumb.
Straight edge lol for amateurs. I can cut straight with a jigsaw lol pretty darn straight lol
@@lisalovelylpa
You are full of shite.
Some good additional comments already. I'd add the importance of rehearsing your movement and settling on a comfortable stance that ensures your movement of head, body, arms flows in a line - not unlike how they teach snooker and pool cue technique. Height of bench, clamps, material all matters for a clean, smooth, and safe cut. Lighting - direction, strength, whiteness. Ergonomics, lighting, etc matters everywhere: people working at desks all twisted and cluttered because they don't think of spending a few seconds when they sit down making sure chair, monitor, coffee cup, etc all in good positions; people speaking into microphones standing at a lectern or sitting in a Zoom meeting. Once the groove is established - it all goes well all day with no stiff back the next day
Like! Gracias por el doblaje al castellano.
Saludos desde Guayaquil Ecuador
Best advice I've seen so far on circular saw 👍
Good tip. I was always just focusing on the blade.
Sorry but a circular saw will NEVER give you a straight cut. You only cut about 1 and a half times the saw length so there is really no room for error. However any longer cuts and a circular saw is impossible to get clean straight lines with. You need a guide.
good tip. That will help straighten my cuts.
Thanks for the tip, but hooray for the accurate 85% of people do this wrong. wow!
Cheers big ears , you just taught this old dog a new trick… much appreciated…
This was a great tip. I have that same saw, wasn't able to make such good cuts. Now I think I understand. Thank you!
I agree completely but best to adjust your blade depth first thing